13035±01
B08025
Turn
A62443
Move
SST
B08048
Move
A62444
Open
SST
2mm 13±2
± INTAKETURBOCHARGER ASSEMBLY (1CD±FTV)
1CD±FTV ENGINE REPAIR MANUAL (RM927E)
OVERHAUL
1. REMOVE COMPRESSOR INLET ELBOW
(a) Remove 2 bolts and the compressor inlet elbow.
2. INSPECT TURBOCHARGER SUB±ASSY
(a) Inspect turbine shaft rotation
(1) Grasp the edge of the turbine shaft, and turn it.
(2) Check that the turbine shaft turns smoothly.
If the turbine shaft turns remarkably heavily or stuck, replace
the bearing housing. At that time, check also the interference
with the turbine housing and compressor housing.
(b) Inspect axial play of turbine shaft
(1) Using a dial indicator, insert the needle of the dial in-
dicator into the exhaust side.
(2) Move the turbine shaft in an axial direction, mea-
sure the axial play of the turbine shaft.
Maximum oil clearance: 0.09 mm (0.0035 in.) or less
If the axial play is greater than maximum, replace the bearing
housing. At that time, check also the interference with the tur-
bine housing and compressor housing.
(c) Inspect radial play of turbine shaft
(1) Using SST and a dial indicator, insert the needle of
the dial indicator into the oil outlet hole, and set it in
the center of the turbine shaft.
SST 09992±00600
(2) Move the turbine shaft in a radial direction, measure
the radial play of the turbine shaft.
Maximum oil clearance: 0.16 mm (0.0063 in.) or less
If the radial play is greater than maximum, replace the bearing
housing. At that time, check also the interference with the tur-
bine housing and compressor housing.
(d) Inspect actuator and waste gate valve operation.
(1) Disconnect the actuator hose from the compressor
housing.
(2) Using SST and a dial indicator, read the graduation
of SST when the actuator push rod moved 2 mm
(0.079 in.).
SST 09992±00242
Standard pressure:
129 ± 140 kPa (1.32 ± 1.43 kgf/cm
2, 18.7 ± 20.3 psi)
A56697
A56698
A56699
A09518
A09519
Hexagon
Wrench
(8mm)
± ENGINE MECHANICALPARTIAL ENGINE ASSY (1CD±FTV)
14±7
1CD±FTV ENGINE REPAIR MANUAL (RM927E)
18. REMOVE OIL PAN SUB±ASSY
(a) Remove the 19 bolts and 3 nuts.
(b) Using a screwdriver, remove the oil pan by prying the por-
tions between the cylinder block and No. 1 oil pan.
NOTICE:
Be careful not to damage the contact surfaces of the cylin-
der block and No. 1 oil pan.
19. REMOVE OIL PUMP ASSY
(a) Remove the 9 bolts.
(b) Remove the oil pump by prying a screwdriver between the
oil pump and main bearing cap.
(c) Remove the gasket.
20. REMOVE ENGINE REAR OIL SEAL RETAINER
(a) Remove the 6 bolts.
(b) Using a screwdriver, remove the oil seal retainer by prying
the portions between the oil seal retainer and main bear-
ing cap.
21. REMOVE OIL CHECK VALVE SUB±ASSY
(a) Using hexagon wrench (8mm), remove the pressure
valve and gasket.
A09519
Hexagon
Wrench
(8mm)
A09476
Seal Width
2 ± 3 mm
A56701
Seal Width
2 ± 4 mm
Seal
PackingNew Gasket
14±10
± ENGINE MECHANICALPARTIAL ENGINE ASSY (1CD±FTV)
1CD±FTV ENGINE REPAIR MANUAL (RM927E)
31. INSTALL OIL CHECK VALVE SUB±ASSY
(a) Using hexagon wrench (8mm), install a new gasket and
the pressure valve.
Torque: 30 Nm (310 kgfcm, 22 ftlbf)
32. INSTALL ENGINE REAR OIL SEAL RETAINER
(a) Apply seal packing to the oil seal retainer as shown in the
illustration.
Seal packing: Part No. 08826±00080 or equivalent
NOTICE:
Install a nozzle that has been cut to a 2 ± 3 mm (0.08
± 0.12 in.) opening.
Parts must be assembled within 15 minutes of ap-
plication. Otherwise the material must be removed
and reapplied.
Immediately remove nozzle from the tube and rein-
stall the cap.
(b) Install the oil seal retainer with 6 bolts. Uniformly tighten
the bolt in several passes.
Torque: 7.4 Nm (75 kgfcm, 65 in.lbf)
33. INSTALL OIL PUMP ASSY
(a) Apply seal packing to the oil pump as shown in the illustra-
tion.
Seal packing: Part No. 08826±00080 or equivalent
NOTICE:
Avoid applying an excessive amount to the surface.
Install a nozzle that has been cut to a 2 ± 4 mm (0.08
± 0.16 in.) opening
Parts must be assembled within 15 minutes of ap-
plication. Otherwise the material must be removed
and reapplied.
Immediately remove nozzle from the tube and rein-
stall the cap.
(b) Install a new gasket to the oil pump.
