2004 SUZUKI GRAND VITARA Battery

YH4
GRAND
VITARA
7B1-26 AUTOMATIC TRANSMISSION (4 A / T)
Operation
VISUAL INSPECTION
Visually check following parts and systems.
INSPECTION ITEM
REFERRING SECTION

A / T fluid ± ± ± ± ± level, leakage, color

A / T fluid hoses ± ± ± ± ± disconnection, looseness, deterioration

Throttle (accelerator) cable ± ± ± ± ± play, installation

A / T throttle cable ± ± ± ± ± play, installation

A / T select cable ± ± ± ± ± installation, operation

Engine oil ± ± ± ± ± level, leakage

Engine coolant ± ± ± ± ± level, leakage

Battery ± ± ± ± ± fluid level, corrosion of terminal

Connectors of electric wire harness ± ± ± ± ± disconnection, friction

Fuses ± ± ± ± ± burning

Parts ± ± ± ± ± installation, damage

Bolt ± ± ± ± ± looseness

Other parts that can be checked visually
Also check following items at engine start, if possible.

ªO / D OFFº lamp

ªPOWERº lamp


Malfunction indicator lamp

Charge warning lamp

Engine oil pressure warning lamp

Engine coolant temp. meter

Other parts that can be checked visually
Section 0B
Section 7B1
Section 6E1 / 6E2
Section 7B1
Section 7B1
Section 0B
Section 0B
Section 6 / 6-1 / 7B1
Section 8
Section 7B1
Section 7B1
Section 6 / 6-1
Section 6H
Section 8 (Section 6A1 / 6A2 /
6A4 for pressure check)

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-31
Brake pedal Released Depressed
Voltage 0 VBattery
voltage
DIAGNOSTIC FLOW TABLE A-1 (NO TCC LOCK-UP OCCURS)
SYSTEM DESCRIPTION
PCM turns TCC solenoid OFF under any of the following conditions.

Brake pedal switch: ON

4WD LOW switch: ON

Cruise control module: TCC OFF command signal is output (if equipped).

ECT: ECT < 30C (86F)
TROUBLESHOOTING
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 person, a driver and tester, on a level road.
STEPACTIONYESNO
1Was ªAUTOMATIC TRANSMISSION
DIAGNOSTIC FLOW TABLEº performed?Go to Step 2.Go to ªAUTOMATIC
TRANSMISSION
DIAGNOSTIC FLOW
TABLEº.
2ECT check:
(1) Warm up engine to normal operating
temperature.
(2) Check ECT using scan tool.
Is ECT more than 30C (86F)?Go to Step 3.Faulty ECT sensor, its
circuit or engine cooling
system.
If OK, substitute a known-
good PCM and recheck.
3Perform running test under the following
conditions and check voltage between
C51-1-8 (G16 / J20 engines) or C51-1-2 (H25
engine) terminal of PCM coupler and ground.

Normal mode in ªDº range.

Transfer ª2Hº position.

Cruise control is not operated (if equipped).

Brake pedal released.

Drive vehicle with TCC ON condition
referring to ªTCC lock-up diagramº in
this section.
Is it battery voltage?Faulty TCC solenoid
valve, its circuit or
transmission.Go to Step 4.
4Is vehicle equipped with H25 engine?Go to Step 5.Go to Step 6.
5Brake switch signal inspection:
(1) With ignition switch ON, check voltage
between E61-31 terminal of PCM coupler
terminal and ground.
Is the result as specified?Go to Step 6.Faulty brake pedal switch
or its circuit.
If OK, substitute a known-
good PCM and recheck.

YH4
GRAND
VITARA
7B1-32 AUTOMATIC TRANSMISSION (4 A / T)
Transfer gear
positionª4Lº or ªNº ª4Hº or ª2Hº
Voltage 0 VBattery
voltage
STEPACTIONYESNO
6ª4WD LOWº switch signal inspection:
(1) With ignition switch ON, check voltage
between C51-1-26 (G16 / J20 engines) or
C51-1-5 (H25 engine) terminal of PCM
coupler and ground.
Is the result as specified?Go to Step 7.Faulty ª4WD LOWº
switch or its circuit.
If OK, substitute a known-
good PCM and recheck.
7Is vehicle equipped with cruise control
system?Go to Step 8.Substitute a known-good
PCM and recheck.
8Cruise control signal inspection:
(1) With ignition switch ON, check voltage
between E61-35 (G16 / J20 engines) or
E61-3 (H25 engine) terminal of PCM
coupler and ground.
Is it battery voltage?Substitute a known-good
PCM and recheck.Faulty cruise control
module or its circuit.
If OK, substitute a known-
good PCM and recheck.

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-33
O / D cut
switchOFF ON
VoltageBattery
voltage0 V
DIAGNOSTIC FLOW TABLE A-2 (NO GEAR SHIFT TO O / D)
SYSTEM DESCRIPTION
PCM does not shift to O / D gear under any of the following conditions.

O / D cut switch: ON

4WD LOW switch: ON

Cruise control module: O / D OFF command signal is output (if equipped).

ECT: ECT < 30C (86F)
TROUBLESHOOTING
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 person, a driver and tester, on a level road.
STEPACTIONYESNO
1Was ªAUTOMATIC TRANSMISSION
DIAGNOSTIC FLOW TABLEº performed?Go to Step 2.Go to ªAUTOMATIC
TRANSMISSION
DIAGNOSTIC FLOW
TABLEº.
2ECT check:
(1) Warm up engine to normal operating
temperature.
(2) Check ECT using scan tool.
Is ECT more than 30C (86F)?Go to Step 3.Faulty ECT sensor,
its circuit or engine
cooling system.
If OK, substitute a known-
good PCM and recheck.
3Perform running test under the following
conditions and check voltage between
C51-1-2 (G16 / J20 engines) or C51-1-6 (H25
engine) terminal of PCM coupler and ground,
C51-1-1 terminal of PCM coupler and ground.

O / D cut switch OFF (ªO / D OFFº lamp OFF).

Normal mode in ªDº range.

Transfer ª2Hº position.

Cruise control is not operated (if equipped).

Drive vehicle with 4th gear condition
referring to ªGear shift diagramº in this
section.
Is each voltage about 0 V?Faulty shift solenoid
valve, its circuit or
transmission.ªGº wire or ªG / Rº wire
shorted to power circuit.
If OK, go to Step 4.
4O / D cut switch signal inspection:
(1) With ignition switch ON, check voltage
between E61-33 (G16 / J20 engines) or
E61-14 (H25 engine) terminal of PCM
coupler and ground.
Is the result as specified?Go to Step 5.Faulty O / D cut switch or
its circuit.
If OK, substitute a known-
good PCM and recheck.

YH4
GRAND
VITARA
7B1-34 AUTOMATIC TRANSMISSION (4 A / T)
Transfer gear
positionª4Lº or ªNº ª4Hº or ª2Hº
Voltage 0 VBattery
voltage
STEPACTIONYESNO
54WD LOW switch signal inspection:
(1) With ignition switch ON, check voltage
between C51-1-26 (G16 / J20 engines) or
C51-1-5 (H25 engine) terminal of PCM
coupler and ground.
Is the result as specified?Go to Step 6.Faulty 4WD LOW switch
or its circuit.
If OK, substitute a known-
good PCM and recheck.
6Is vehicle equipped with cruise control
system?Go to Step 7.Substitute a known-good
PCM and recheck.
7Cruise control signal inspection:
(1) With ignition switch ON, check voltage
between E61-35 (G16 / J20 engines) or
E61-3 (H25 engine) terminal of PCM
coupler and ground.
Is it battery voltage?Substitute a known-good
PCM and recheck.Faulty cruise control
module or its circuit.
If OK, substitute a known-
good PCM and recheck.

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-41
C51-1
-18C51-1
-17C51-1
-16C51-1
-15C51-1
-28C51-1
-27 G16/
J20
H25
C51-1-4 C51-1-3 C51-1-13 C51-1-12 C51-1-20 C51-1-19
Terminal
Select
lever
position
TROUBLESHOOTING (DTC P0705)
STEPACTIONYESNO
1Was ªA / T DIAG. FLOW TABLEº performed?Go to Step 2.Go to ªA / T DIAG.
FLOW TABLEº.
2Check Transmission Range Switch (Sensor) Circuit for
Operation.
When using SUZUKI scan tool:
1) Connect SUZUKI scan tool to DLC with ignition
switch OFF.
2) Turn ignition switch ON and check transmission
range signal (P, R, N, D, 2 or L) on display
when shifting select lever to each range.
Is applicable range indicated?
When not using SUZUKI scan tool:
1) Turn ignition switch ON.
2) Check voltage at terminals C51-1-15, C51-1-16,
C51-1-17, C51-1-18, C51-1-27 and C51-1-28 for
G16/J20 (C51-1-4, C51-1-3, C51-1-13, C51-1-12,
C51-1-20 and C51-1-19 for H25) respectively with
select lever shifted to each range.
Taking terminal C51-1-28 for G16/J20 (C51-1-20 for
H25) as an example, is battery voltage indicated
only when select lever is shifted to ª2º range and
0 V for other ranges as shown in figure?
Check voltage at other terminals likewise, referring
to figure.
Are check results satisfactory?Intermittent trouble.
Check for intermittent
referring to ªIntermit-
tent and Poor
Connectionº in
section 0A.Go to Step 3.
3Check Select Cable for Adjustment referring to ªSelect
Cable Adjustmentº in this section.
Is it adjusted correctly?Go to Step 4.Adjust.
4Check Transmission Range Switch for Installation
Position.
1) Shift select lever to ªNº range.
2) Check that ªNº reference line on switch and center
line on shaft are aligned.
Are they aligned?Go to Step 5.Adjust.
5Check Transmission Range Switch (Sensor) referring
to ªTransmission Range Switchº in this section.
Are check results satisfactory?ªYº, ªOr / Gº, ªRº,
ªOr / Blº, ªY / Gº,
ªG / Orº or ªG / Blº
circuit open or short.
If wires and
connections are OK,
substitute a known-
good PCM and
recheck.Replace TR switch.
Fig. for Step 2.

YH4
GRAND
VITARA
1
1. 4WD low switch
AUTOMATIC TRANSMISSION (4 A / T) 7B1-53
TROUBLESHOOTING (DTC P1875)
STEPACTIONYESNO
1Was ªA / T DIAG. FLOW TABLEº performed?Go to Step 2.Go to ªA / T DIAG.
FLOW TABLEº.
24WD low switch and its circuit check:
When using SUZUKI scan tool:
1) Connect SUZUKI scan tool to DLC with ignition
switch OFF.
2) Turn ignition switch ON.
3) Select ªData listº mode on scan tool.
4) Check 4WD low switch signal (ON or OFF) on
display when shifting transfer lever to each
position.
4H or 2H position : OFF
4L position : ON
Is OFF / ON displayed as described above?
When not using SUZUKI scan tool:
1) Remove PCM cover.
2) Turn ignition switch ON.
3) Check voltage at terminal C51-1-26 for G16 / J20
(C51-1-5 for H25) of PCM connector connected
when shifting transfer lever to each position.
4H or 2H position : 10 ± 14 V
4L position : 0 ± 1 V
Is voltage as specified?Check for poor con-
nection at the termi-
nal of PCM if voltme-
ter is used in Step 2.
If connection is OK,
intermittent trouble
or faulty PCM.
Check for intermittent
referring to ªIntermit-
tent and Poor
Connectionº in
Section 0A.Go to Step 3.
34WD low switch check:
1) Check 4WD low switch for operation referring to
ª4WD Low Switch Inspectionº below.
Is check result satisfactory?ªOr / Wº or ªBº circuit
open or short. If wires
and connections are
OK, substitute a
known-good PCM
and recheck.Replace 4WD low
switch.
4WD Low Switch Inspection
1) Disconnect negative cable at battery.
2) Disconnect 4WD low switch coupler.
3) Check continuity between 4WD low switch terminals.
There should be continuity when transfer lever shifted to 4L posi-
tion and should be infinity when transfer lever shifted to 4H or 2H
positions.
If not, replace 4WD low switch.
4) Connect 4WD low switch coupler and battery negative cable.

YH4
GRAND
VITARA
1. Manual selector assembly
(Select lever assembly)
2. Manual lever assembly
3. Select cable bracket
4. Select indicator
5. Slide cover
6. Select lever knob7. Spring
8. Knob button
9. Shift lock solenoid rod
10. Shift lock solenoid
11. Cover
12. Illumination lamp
13. Interlock cam
1. Interlock cam pin
(only for new selector assembly) Tightening Torque
(a): 18 N
.m (1.8 kg-m, 13.5 lb-ft)1. Manual lever
assembly
2. Select indicator
assembly
3. Illumination lamp
assembly
4. Bulb filter
5. Bulb
6. Knob assembly
7. Shift lock solenoid
Type-1 Type-2
Type-1
7B1-62 AUTOMATIC TRANSMISSION (4 A / T)
MANUAL SELECTOR ASSEMBLY
REMOVAL
1) Disconnect negative cable at battery.
2) Remove console box.
3) Disconnect connector for illumination lamp, shift lock solenoid
and overdrive OFF switch.
4) Disconnect interlock cable from interlock cam of selector as-
sembly.
5) Remove selector assembly mounting bolts.
6) Disconnect select cable from lever of selector assembly.
INSTALLATION
NOTE:
New selector assembly of Type-1 is supplied with held inter-
lock cam at interlock cable connecting position with pin. Re-
move this pin after connecting interlock cable to interlock cam
and tightening cable nut.
Reverse removal procedure to install noting the followings.

Connect interlock cable end to cam referring to steps 2) to 8) of
ªInterlock Cable Installationº section.

Upon completion of installation, confirm that brake (key) interlock
system operates properly.