2004 SUZUKI GRAND VITARA Engine

YH4
GRAND
VITARA
For CAMI production vehicle
For IWATA production vehicle
2. High pressure side (Delivery side hose)
3. Lower pressure side (Suction side pipe)
AIR CONDITIONING (OPTIONAL) 1B-49
COMPRESSOR ASSEMBLY
CAUTION:
None of refrigerant, compressor oil and component parts is interchangeable between two types of A / C:
one using CFC-12 (R-12) and the other using HFC-134a (R-134a).
For identification between these two types, refer to page 1B-2.
When replenishing or changing refrigerant and compressor oil and when replacing parts, make sure
that the material or the part to be used is appropriate to the A / C installed in the vehicle being serviced.
Use of incorrect refrigerant or compressor oil will result in leakage of refrigerant, damage in parts or
other faulty condition.
PRECAUTION
When servicing the compressor, keep dirt or foreign material away from getting on or into the compressor parts
and system. Clean tools and a clean work area are important for proper service.
The compressor connection and the outside of the compressor should be cleaned before any ªOn-vehicleº repair
or before removal of the compressor. The parts must be kept clean at all times and any parts to be reassembled
should be cleaned with Trichloroethane, naphtha, kerosene or equivalent solvent and dried with dry air. Use only
lint free cloths to wipe parts.
The operations described are based on bench overhaul with compressor removed from the vehicle, except as
noted. They have been prepared in order of accessibility of the components.
When compressor is removed from the vehicle for servicing, the oil remaining in the compressor should be dis-
carded and new refrigerant oil added to the compressor.
Minor repair procedures may be done on the vehicle without discharging the system. Major repair procedures re-
quire that the system be discharged of refrigerant.
INSPECTION
1) Install manifold gauge set (1) as shown in the figure.
2) Close Hi (4) and Lo (5) hand valves.
3) Run engine at fast idle.
4) Check compressor assembly for following items.
If any of the above checks indicated a defect, repair compressor
assembly.

High pressure gauge reading is not low and low pressure
gauge reading is not higher than normal.

Metallic sound.

Leakage from shaft seal.

YH4
GRAND
VITARA
1B-50 AIR CONDITIONING (OPTIONAL)
REMOVAL
1) Run engine at idle with A / C ON for 10 minutes.
2) Disconnect negative (±) cable at battery.
3) Recover refrigerant from refrigeration system using recovery
and recycling equipment.
NOTE:
The amount of compressor oil at removed must be mea-
sured and the same amount must be poured when installing
the compressor.
4) Disconnect thermal protector lead wire.
5) Disconnect suction and discharge hoses from compressor as-
sembly.
NOTE:
Cap open fitting immediately to keep moisture out of sys-
tem.
6)For G16 engine:
Remove compressor drive belt by loosening compressor as-
sembly mounting bolts.
For J20 engine:
Remove generator belt. Refer to Section 6H.
For H25 engine:
Remove compressor drive belt by loosening tension pulley bolt.
7) Remove compressor with magnet clutch assembly from its
mount.
8) If compressor assembly is replaced. Drain oil from compressor
assembly, and measure its amount.

YH4
GRAND
VITARA
AIR CONDITIONING (OPTIONAL) 1B-51
G16 engine
J20 engine
H25 engine
3. Compressor pulley
4. Crankshaft pulley
INSTALLATION
FOR IWATA PRODUCTION VEHICLE
1) Pour new compressor oil. The amount must be the same with
the amount measured in REMOVAL.
NOTE:
Compressor assembly supplied from factory is filled up
with following amount of oil.
Amount of oil in compressor: 120 cm
3 (120 cc, 7.5 in3)
2)For G16 engine:
Install compressor assembly temporarily to bracket, then install
compressor drive belt (2).
For J20 and H25 engines:
Install compressor assembly to its bracket.
Tighten bolts (a) first, then (b).
Tightening Torque
(a), (b): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
3) Connect suction and discharge hoses to compressor assembly.
4)For G16 engine:
Tension compressor drive belt (2) by tightening compressor as-
sembly mounting bolts. Refer to Section 3B1 for drive belt ten-
sion.
Tighten bolt (a) first, then (b).
Tightening Torque
(a), (b): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
For J20 engine:
Install generator belt (1). Refer to Section 6H for details.
For H25 engine:
Install compressor drive belt (2). Refer to Section 3B1 for instal-
lation and belt tension.
5) Connect thermal protector lead wire.
6) Evacuate and charge system according to previously described
procedure.
CAUTION:
Be sure to use HFC-134a (R-134a) compressor oil.

YH4
GRAND
VITARA
1B-52 AIR CONDITIONING (OPTIONAL)
G16 engine
J20 engine
3. Compressor pulley
4. Crankshaft pulley
FOR CAMI PRODUCTION VEHICLE
1) Pour new compressor oil. The amount must be the same with
the amount measured in REMOVAL.
NOTE:
Compressor assembly supplied from factory is filled up
with the following amount of oil.
Amount of oil in compressor: 120 cm
3 (120 cc, 7.5 in3)
2)For G16 engine:
Install compressor assembly temporarily to bracket, then install
compressor drive belt (2).
For J20 engine:
Install compressor assembly to its bracket.
Tighten bolts (a).
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
3) Connect suction and discharge hoses to compressor assembly.
4)For G16 engine:
Tension compressor drive belt (2) by tightening compressor as-
sembly mounting bolts. Refer to Section 3B1 for drive belt ten-
sion.
Tighten bolt (a) first, then (b).
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
For J20 engine:
Install generator belt (1). Refer to Section 6H for details.
5) Connect thermal protector lead wire.
6) Evacuate and charge system according to previously described
procedure.
CAUTION:
Be sure to use HFC-134a (R-134a) compressor oil.

YH4
GRAND
VITARA
1. Power steering gear box
2. Power steering pump
3. P / S fluid reservoir
1. Power steering pump
2. Valve section
3. P / S fluid reservoir
4. Rack
5. Pinion
6. Cylinder
3B1-2 POWER STEERING (P / S) SYSTEM
GENERAL DESCRIPTION
POWER STEERING SYSTEM
The power steering (P / S) system in this vehicle reduces the driver's effort needed in turning the steering wheel
by utilizing the hydraulic pressure generated by the power steering (P / S) pump which is driven by the engine.
It is an integral type with the rack and pinion gears and the control valve unit, hydraulic pressure cylinder unit all
built in the steering gear box.

YH4
GRAND
VITARA
1. Suction connector
2. O-ring
3. Pressure switch
4. Flow control valve
(Relief valve)
5. Spring
6. Plug
7. Pump cover
8. Cam ring
9. Vane
10. Rotor
11. Snap ring
12. Side plate
13. Pulley (pump shaft)
14. Oil seal
15. Pump body
16. Flow control valve Assembly
3B1-4 POWER STEERING (P / S) SYSTEM
POWER STEERING (P / S) PUMP
The power steering pump is a vane type and is driven by the V-ribbed belt from the crankshaft.
ModelVane type
Hydraulic
pressure
controlRelieved
pressure
6500 kPa (65 kg / cm2, 924 psi)
G16 Type engine . . . . . . . . . . . . . . . . . . . . . .
7000 kPa (70 kg / cm
2, 995 psi)
J20 Type engine . . . . . . . . . . . . . . . . . . . . . . .
7350 kPa (73.5 kg / cm
2, 1045 psi)
H25 Type engine . . . . . . . . . . . . . . . . . . . . . .
ControlFlow control valve
deviceRelief valve
Power steering
pressure switch
Switch turns on (closes) when the
pressure is higher than 2500 ± 3500 kPa
(25 ± 35 kg / cm
2, 356 ± 498 psi).
ECM uses this signal for idle speed control.
Capacity0.70 ± 0.75

(1.48 / 1.23 ± 1.58 / 1.32 US / Imp. pt)
Specified fluidDEXRON
II, DEXRON
III A / T fluid
or equivalent
FLOW CONTROL VALVE
As the discharge rate of the P/S pump increases in proportion to the
pump revolution speed, a flow control valve is added to control it so
that the optimum amount of fluid for steering operation is supplied
according to the engine speed (driving condition).
Described below is its operation at different engine speed.

YH4
GRAND
VITARA
POWER STEERING (P / S) SYSTEM 3B1-7
STEERING WHEEL
STEERING WHEEL PLAY CHECK
Check steering wheel for looseness or rattle by trying to move it in
its shaft direction and lateral direction.
If found defective, repair or replace.
Check steering wheel for play, holding car in straight forward condi-
tion on the ground and with engine stopped.
Steering wheel play ªaº: 0 ± 30 mm (0 ± 1.2 in.)
If steering wheel play is not within specification, inspect as follows
and replace if found defective.

Tie-rod end ball stud for wear

Lower ball joint for wear

Steering shaft joint for wear

Steering pinion or rack gear for wear or breakage

Each part for looseness
STEERING FORCE CHECK
1) Place vehicle on level road and set steering wheel at straight-
ahead position.
2) Check that tire inflation pressure is as specified. (Refer to tire
placard.)
3) Start engine and keep it running till power steering fluid is
warmed to 50 to 60C (122 to 140F).
4) With engine idling, measure steering force by pulling spring ba-
lancer hooked on steering wheel in tangential direction.
Steering force: Less than 50 N (5.0 kg, 11.0 lb)
POWER STEERING FLUID
POWER STEERING FLUID LEVEL CHECK
With engine stopped, check fluid level indicated on P / S fluid reser-
voir, which should be between ªMAXº and ªMINº marks. If it is lower
than ªMINº mark, fill fluid up to ªMAXº mark.
NOTE:

Be sure to use an specified power steering fluid.

Fluid level should be checked when fluid is cool.

YH4
GRAND
VITARA
[D] [C] [A]
1. P / S pump pulley
2. A / C compressor
pulley (if equipped)
3. Crankshaft pulley
4. Tension pulley
5. Tension pulley bolts[A]: G16 type engine with A / C
[B]: G16 type engine without A / C
[C]: H25 type engine with A / C
[D]: H25 type engine without A / C
[B]
3B1-8 POWER STEERING (P / S) SYSTEM
POWER STEERING PUMP DRIVE BELT
NOTE:
For J20 Type engine, refer to Section 6H ªGENERATOR BELTº.
INSPECTION
Check that belt is free from any damage and properly fitted in pulley
groove.
BELT TENSION CHECK
Check belt tension by measuring how much it deflects when
pushed at intermediate point between pulleys with about 10 kg
(22 lb) force.
Deflection of P / S belt:
6 ± 9 mm (0.24 ± 0.35 in.) G16 Type engine. . . . . . . . . . . . . . . . .
4 ± 7 mm (0.16 ± 0.28 in.) H25 Type engine. . . . . . . . . . . . . . . . .
BELT TENSION ADJUSTMENT
[For G16 Type engine]
a) To adjust P / S pump drive belt tension, use adjusting bolt of com-
pressor for A / C equipped vehicles and that of P / S pump for ve-
hicles without A / C.
b) Adjust belt tension to above specification.
c) Then tighten adjusting and mounting bolts to specified torque.
[For J20 Type engine]
To adjust P / S pump drive belt tension, refer to ªGENERATOR
BELTº in Section 6H.
[For H25 Type engine]
a) To adjust P / S pump drive belt tension, loosen tension pulley
bolts and turn tension pulley using hexagon wrench.
b) Adjust belt tension to above specification.
Then tighten tension pulley bolts to specified torque.
Tightening Torque
Tension pulley bolts: 25 N
.m (2.5 kg-m, 18.5 lb-ft)