2004 SUZUKI GRAND VITARA Engine

YH4
GRAND
VITARA
1. Full level mark (hole)
2. Low level mark (hole)
0B-10 MAINTENANCE AND LUBRICATION
NOTE:
Engine oil capacity is specified. However, note that the
amount of oil required when actually changing oil may
somewhat differ from the data in the table depending on
various conditions (temperature, viscosity, etc.).
7) Check oil filter and drain plug for oil leakage.
8) Start engine and run it for three minutes. Stop it and wait five min-
utes before checking oil level. Add oil, as necessary, to bring oil
level to FULL level mark on dipstick.
NOTE:
Step 1) ± 7) outlined above must be performed with ENGINE
NOT RUNNING. For step 8), be sure to have adequate ven-
tilation while engine is running.
ITEM 1-5
Engine Coolant Change
WARNING:
To help avoid danger of being burned, do not remove radia-
tor cap while engine and radiator are still hot. Scalding fluid
and steam can be blown out under pressure if cap is taken
off too soon.
1) Remove radiator cap when engine is cool.
2) Loosen radiator drain plug to drain coolant.
3) Remove reservoir, which is on the side of radiator, and drain.
4) Tighten plug securely. Also reinstall reservoir.
5) Fill radiator with specified amount of coolant, and run engine for
2 or 3 minutes at idle. This drives out any air which may still be
trapped within cooling system. STOP ENGINE. Add coolant as
necessary until coolant level reaches the filler throat of radiator.
Reinstall radiator cap.

YH4
GRAND
VITARA
MAINTENANCE AND LUBRICATION 0B-11
1. Reservoir
2. FULL level mark
3. LOW level mark
4. Arrow mark
5. Reservoir cap
546) Add coolant to reservoir so that its level aligns with Full mark.
Then, reinstall cap aligning arrow marks on reservoir and cap.
NOTE:
When installing reservoir cap, align arrow marks on reser-
voir and cap.
CAUTION:
When changing engine coolant, use mixture of 50% wa-
ter and 50% ANTIFREEZE / ANTICORROSION COOLANT
for the market where ambient temperature falls lower
than ±16C (3F) in winter, and mixture of 70% water and
30% ANTIFREEZE / ANTICORROSION COOLANT for the
market where ambient temperature doesn't fall lower
than ±16C (3F).
Even in a market where no freezing temperature is antici-
pated, mixture of 70% water and 30% ANTIFREEZE / AN-
TICORROSION COOLANT should be used for the pur-
pose of corrosion protection and lubrication.
ITEM 1-6
Exhaust System Inspection
WARING:
To avoid danger of being burned, do not touch exhaust sys-
tem when it is still hot. Any service on exhaust system
should be performed when it is cool.
When carrying out periodic maintenance, or the vehicle is raised for
other service, check exhaust system as follows:

Check rubber mountings for damage, deterioration, and out of
position.

Check exhaust system for leakage, loose connections, dents and
damages.
If bolts or nuts are loose, tighten them to specification.

Check nearby body areas for damaged, missing, or misposi-
tioned parts, open seams, holes, loose connections or other de-
fects which could permit exhaust fumes to seep into the vehicle.

Make sure that exhaust system components have enough clear-
ance from the underbody to avoid overheating and possible dam-
age to the floor carpet.

Any defects should be fixed at once.

YH4
GRAND
VITARA
The figure shows right-hand steering vehicle
The figure shows right-hand steering vehicle
0B-22 MAINTENANCE AND LUBRICATION
ITEM 6-14
Steering System Inspection
1) Check steering wheel for play and rattle, holding vehicle in
straight forward condition on the ground.
Steering wheel play ªaº: 0 ± 30 mm (0 ± 1.2 in.)
2) Check universal joints of steering shaft for rattle and damage. If
rattle or damage is found, replace defective part with a new one.
3) Check steering linkage for looseness and damage. Repair or re-
place defective part, if any.
4) Check bolts and nuts for tightness and retighten them as neces-
sary. Repair or replace defective parts, if any.
Refer to table of Tightening Torque Specification in Section 3B
(or 3B1) and 3C (or 3C1) for particular check points.
5) Check boots of steering linkage for damage (leaks, detachment,
tear, dent, etc.). If damage is found, replace it with new one.
If any dent is found on steering rack boots, correct it to original
shape by turning steering wheel to the right or left as far as it
stops and holding it for a few seconds.
6) Check wheel alignment.
NOTE:
For details of wheel alignment, refer to Wheel Alignment in
Section 3A.
ITEM 6-15
Power Steering (P / S) System Inspection (if equipped)
1) Visually check power steering system for fluid leakage and hose
for damage and deterioration.
Repair or replace defective parts, if any.
2) With engine stopped, check fluid level indicated on fluid tank,
which should be between MAX and MIN marks. If it is lower than
MIN, fill fluid up to MAX mark.
NOTE:

Be sure to use an equivalent of DEXRON

-II or DEX-
RON

-III for P / S fluid.

Fluid level should be checked when fluid is cool.

YH4
GRAND
VITARA
1. ªUPPERº or ªLOWERº mark
MAINTENANCE AND LUBRICATION 0B-23
3) Visually check pump drive belt for cracks and wear.
4) Check belt for tension, referring to item 1-1.
If necessary, have belt adjusted or replaced.
ITEM 6-16
All Hinges, Latches and Locks Inspection
Doors
Check that each door of front, rear and back doors opens and
closes smoothly and locks securely when closed.
If any malfunction is found, lubricate hinge and latch or repair door
lock system.
Engine hood
Check that secondary latch operates properly (check that second-
ary latch keeps hood from opening all the way even when pulling
hood release handle inside vehicle.). Also check that hood opens
and closes smoothly and properly and hood locks securely when
closed.
If any malfunction is found, lubricate hinge and latch, or repair hood
lock system.
ITEM 6-17
Air Conditioning Filter (if equipped)
Inspection
1) Remove air conditioning filter from cooling unit referring to Sec-
tion 1B.
2) Check filter for dirt. Replace excessively dirty filter.
3) Blow off dust by compressed air from air outlet side of filter.
4) Install filter to cooling unit referring to Section 1B.
Replacement
Replace air conditioning filter with new one referring to Section 1B.

YH4
GRAND
VITARA
0B-24 MAINTENANCE AND LUBRICATION
FINAL INSPECTION
Seats
Check that seat slides smoothly and locks securely at
any position. Also check that reclining mechanism of
front seat back allows it to be locked at any angle.
Seat Belt
Inspect belt system including webbing, buckles, latch
plates, retractors and anchors for damage or wear.
If ªREPLACE BELTº label on front seat belt is visible,
replace belt.
Check that seat belt is securely locked.
Battery Electrolyte Level Check
Check that the electrolyte level of all battery cells is
between the upper and lower level lines on the case.
If battery is equipped with built-in indicator, check bat-
tery condition by the indicator.
Accelerator Pedal Operation
Check that pedal operates smoothly without getting
caught or interfered by and other part.
Engine Start
Check engine start for readiness.
On automatic transmission vehicles, try to start the
engine in each select lever position. The starting mo-
tor should crank only in ªPº (Park) or ªNº (Neutral).
On manual transmission vehicles, place the shift le-
ver in ªNeutral,º depress clutch pedal fully and try to
start.
Exhaust System Check
Check for leakage, cracks or loose supports.
Clutch (For Manual transmission)
Check for the following:

Clutch is completely released when depressing
clutch pedal.

No slipping clutch occurs when releasing pedal and
accelerating.

Clutch itself is free from any abnormal condition.
Gearshift or Select Lever (Transmission)
Check gear shift or select lever for smooth shifting to
all positions and for good performance of transmis-
sion in any position.
With automatic transmission equipped vehicle, also
check that shift indicator indicates properly according
to which position select lever is shifted to.
With automatic transmission equipped vehicle, make
sure that vehicle is at complete stop when shifting se-
lect lever to ªPº range position and release all brakes.
Brake
[Foot brake]
Check the following:

that brake pedal has proper travel,

that brake works properly,

that it is free from noise,

that braking force is applied equally on all wheels,

and that brake do not drag.
[Parking brake]
Check that lever has proper travel.
WARNING:
With vehicle parked on a fairly steep slope,
make sure nothing is in the way downhill to
avoid any personal injury or property damage.
Be prepared to apply regular brake quickly
even if vehicle should start to move.
Check to ensure that parking brake is fully effective
when the vehicle is stopped on the safe slope and
brake lever is pulled all the way.
WARNING:
When carrying out road tests, select a safe
place where no man or no running vehicle is
seen so as to prevent any accident.
WARNING:
Before performing the following check, be
sure to have enough room around the vehicle.
Then, firmly apply both the parking brake and
the regular brakes. Do not use the accelerator
pedal. If the engine starts, be ready to turn off
the ignition promptly. Take these precautions
because the vehicle could move without warn-
ing and possibly cause personal injury or
property damage.

YH4
GRAND
VITARA
MAINTENANCE AND LUBRICATION 0B-25
Steering

Check to ensure that steering wheel is free from in-
stability, or abnormally heavy feeling.

Check that the vehicle does not wander or pull to
one side.
Engine

Check that engine responds readily at all speeds.

Check that engine is free from abnormal noise and
abnormal vibration.
Body, Wheels and Power Transmitting System
Check that body, wheels and power transmitting sys-
tem are free from abnormal noise and abnormal
vibration or any other abnormal condition.
Meters and Gauge
Check that speedometer, odometer, fuel meter, tem-
perature gauge, etc. are operating accurately.
Lights
Check that all lights operate properly.
Windshield Defroster
Periodically check that air comes out from defroster
outlet when operating heater or air conditioning.
Set fan switch lever to ªHIº position for this check.
RECOMMENDED FLUIDS AND LUBRICANTS
Engine oilSG, SH or SJ (Refer to engine oil viscosity chart in item 1-4)
Engine coolant (Ethylene glycol
base coolant)ªAntifreeze / Anticorrosion coolantº
Brake fluidDOT 3
Manual transmission oilRefer to Section 7A or 7A1Transfer oilRefer to Section 7A or 7A1.
Differential oil (front & rear)Refer to Section 7E or 7F.
Automatic transmission fluid and
Power steering fluidRefer to Section 3B1 or 7B1.
Door hingesEngine oil or water resistance chassis greaseHood latch assemblyEngine oil or water resistance chassis grease
Key lock cylinderSpray lubricant

YH4
GRAND
VITARA
HEATER AND VENTILATION 1A-17
1. Dash panel (engine room) 2. Nuts
REMOVAL
WARNING:
Failure to follow the following procedure and WARNING
may cause air bag deployment, personal injury, damage to
parts, or air bag being unable to deploy.

Never rest a steering column assembly on steering wheel
with air bag (inflator) module face down and column verti-
cal.

When handling the air bag (inflator) modules (driver and
passenger), be careful not to drop it or apply an impact to
it. If an excessive impact was applied (e.g., dropped from
a height of 91.4 cm (3 feet) or more, never attempt disas-
sembly or repair but replace it with a new one.

When grease, cleaning agent. Oil, water, etc. has got onto
air bag (inflator) modules (driver and passenger), wipe off
immediately with a dry cloth.
1) Disconnect negative (±) cable at battery.
2) Disable air bag system, if equipped. Refer to DISABLING AIR
BAG SYSTEM in Section 10B.
3) Drain engine coolant and disconnect heater hose (1) from
heater unit.
4) Remove instrument panel, refer to item INSTRUMENT PANEL
REMOVAL in Section 9.
5) Remove cooling unit (If equipped).
Refer to item EVAPORATOR (COOLING UNIT) REMOVAL in
Section 1B.
6) Disconnect rear duct (4) from heater unit.
7) Disconnect heater mode control actuator lead wire (1) at cou-
plers.
8) Remove A / C controller (2) (If equipped).
9) Remove SDM (3) (If equipped).
10) Remove heater unit.

YH4
GRAND
VITARA
1A-18 HEATER AND VENTILATION
11) Remove heater core pipe clamps (1) and grommet (2).
12) Pull out heater core (1) from unit (2).
INSTALLATION
1) Install heater unit by reversing removal procedure, noting the
following items.

When installing each part, be careful not to catch any cable or
wiring harness.

When installing steering column assembly, refer to STEER-
ING COLUMN INSTALLATION in Section 3C or 3C1.
2) Install control cables. (Refer to HEATER CONTROL CABLES in
this section.)
3) Fill engine coolant to radiator.
4) Enable air bag system, if equipped. Refer to ENABLING AIR
BAG SYSTEM in Section 10B.
5) Evacuate and charge system. Refer to items EVACUATING
SYSTEM and PROCEDURE OF CHARGING in Section 1B.