1 -Fuel filler cap warning light.
2 - Door open warning light.
3 - Dipped beam headlamps indicator light.
4 - Main beam headlamps indicator light.
5 - Rev. counter.
6 - Left-hand direction indicator.
7 - Central STOP warning light.
8 - Low fuel level warning light.
9 - Fuel gauge. 10 -
Service indicator, oil level indica-
tor and total distance recorder.
11 - Right-hand direction indicator.
12 - Speedometer.
13 - Clogging of the particulateemission filter warning light(Diesel).
14 - Front fog lamps indicator light.
15 - Rear fog lamp indicator light.
16 - Dynamic stability control(ASR/ESP) warning light(according to version). 17 -
Low coolant level warning light.
18 - Coolant temperature indicator.
19 - Trip recorder zero reset button.
20 - Handbrake and low brake fluid level warning light.
21 - Seat belt not fastened warninglight (according to version).
22 - Air bags warning light.
23 - ABS warning light.
24 - Engine diagnostics warninglight*.
25 - Battery charge warning light.
26 - Diesel engine preheating indica-tor light.
27 - Passenger air bag disarmingwarning light.
28 - Water in diesel filter warninglight.
29 - Front brake pad wear warninglight.
30 - Engine oil pressure warninglight.
31 - Electronic immobiliser warninglight.
32 - Lighting rheostat.
33 - Engine oil temperature indicator.
* According to engine.
YOUR 406 COUPE IN DETAIL 105
INSTRUMENT PANEL DIALS: PETROL / DIESEL
02-02-2004
YOUR 406 COUPE IN DETAIL
106
1 -
Fuel filler cap warning light.
2 - Door open warning light.
3 - Dipped beam headlamps indi- cator light.
4 - Main beam headlamps indicatorlight.
5 - Rev. counter.
6 - Left-hand direction indicator.
7 - Central STOP warning light.
8 - Low fuel level warning light.
9 - Fuel gauge. 10 -
Service indicator, oil level indi- cator and total distance
recorder.
11 - Right-hand direction indicator.
12 - Speedometer.
13 - Front fog lamps indicator light.
14 - Rear fog lamp indicator light.
15 - Dynamic Stability Control(ASR/ESP) warning light.
16 - Low coolant level warning light. 17 -
Coolant temperature indicator.
18 - Trip recorder zero reset button.
19 - Handbrake and low brake fluid level warning light.
20 - Seat belt not fastened warninglight (according to version).
21 - Air bags warning light.
22 - ABS warning light.
23 - Engine diagnostics warninglight*.
24 - Battery charge warning light.
25 - Passenger air bag disarmingwarning light.
26 - Front brake pad wear warning light.
27 - Engine oil pressure warninglight.
28 - Operating programmes.
29 - Gear lever position indicator.
30 - Electronic immobiliser warninglight.
31 - Lighting rheostat.
32 - Engine oil temperature indicator.
* According to engine.
INSTRUMENT PANEL DIALS: AUTOMATIC GEARBOX
02-02-2004
02-02-2004
AUTOMATIC SWITCHING ON OF THE LIGHTS The side lights and dipped beam headlamps switch on automatically if
the light is poor, or during continuousoperation of the windscreen wipers.
They switch off as soon as the lightbecomes bright enough or the wind-screen wipers stop. This function is active when the vehi-
cle is supplied to the customer.
To disarm or activate the function: Place the key in the accessories position (1st notch),
Press the end of the lights stalkfor more than two seconds.
Note: in foggy weather, the bright-
ness sensor can detect sufficientlight. Because of this, the lights do
not come on automatically. Do not cover the brightness sen-
sor connected to the rain sensor,located on the windscreen behind
the mirror. It is used for automat-ic switching on of the lights. Operating check Activation Activation of this function is accom- panied by an audible signal and themessage
"Automatic lighting of
the headlamps activated" on the
multi-function display. Note: Manual operation of the lights
stalk always takes priority Disarming Disarming of the function is accom- panied by an audible signal and themessage "Automatic lighting of
the headlamps deactivated" on the
multi-function display. When driving, if this function is
switched off when the headlampswould switch on in automatic mode,the lights remain on. It is howeverpossible to disarm this function and
switch off the lights by:
Ð manually switching off the lights using the lights stalk,
Ð switching off the engine. If the brightness sensor does not
function correctly,
the system acti-
vates the function (the lights come
on). The driver is alerted by theflashing of the ''dipped beam'' warn-ing light on the instrument panel.
Contact a PEUGEOT dealer to have the system checked. Follow me Home When there is a low level of bright- ness or at night, if you leave yourvehicle, the side lights and thedipped beam lights may remain onfor approximately one minute. This function can only be used if the automatic switching on of the lightsmode is activated then: with the key in the accessories position (1st notch), flash theheadlamps,
get out of the car and lock it.
YOUR 406 COUPE IN DETAIL 103
02-02-2004
HORNPress one of the spokes or the centre of the steeringwheel.
HEADLAMP ADJUSTMENT Depending on the load in your vehi- cle, adjusting the beam of the head-lamps is recommended as follows.0 - 1 or 2 people in the front seats.
Ð- 3 people.
1- 4 people.
2 - 4 people + maximum authorised load.
3 - Driver + maximum authorised load.
Initial setting is position 0. HAZARD WARNING LIGHTS Press the button, the direction indi- cators flash. They can operate with the ignition
off.
STEERING WHEEL HEIGHT
AND DEPTH ADJUSTMENT
When the vehicle is stationary, unlock the steering wheel by pullinghandle
A.
Adjust the height and depth of thesteering wheel, then lock it by push-ing handle Adown fully.
YOUR 406 COUPE IN DETAIL 121
Automatic lighting of hazard warning lights*
When braking in an emergency, depending on the force of decelera-tion, the hazard warning lights come
on automatically. They switch offautomatically the first time youaccelerate.
It is also possible to switch them off by pressing the button.
* According to destination.
02-02-2004
MAINTENANCE OF YOUR 406 COUPE35
CHANGING A BULB
1 - Dipped beam headlamps
2 - Main beam headlamps
Two bulbs
(H7-55 W).
Ð Remove the red plastic cover.
Ð Press the tab and remove the protective cover corresponding to the faulty bulb.
Ð Disconnect the connector.
Ð Press the end of the securing clip to remove it. Change the bulb.
Ð When fitting, ensure that the direction notches are positioned correctly and that the securing clip is corrrectly fixed.
Ð Reconnect the connector.
Ð Replace the protective cover.
3 - Side lights (W 5 W)
Turn the socket using the lever and remove it. Change the bulb.
4 - Direction indicators (PY 21 W)
Turn the bulb holder a quarter turn and remove it. Change the bulb. Notes: only handle H7 bulbs using a dry cloth.
To replace the left-hand bulbs, remove the battery protective cover. Direction indicator repeater
(WY 5 W)
Ð Pull the rear section of the trans-
parent cover and release the
assembly.
Ð Turn the connector a quarter turn and remove it.
Ð Change the bulb.
Amber bulbs must be replaced by bulbs of iden-tical specification and
colour.
In certain climatic conditions (lowtemperatures, humidity), the
presence of condensation onthe inside of the headlampglass is normal ; it disappears a
few minutes after the lights switchon.
02-02-2004
MAINTENANCE OF YOUR 406 COUPE41
Fuse N¡ Rating
Functions
11* 10 A Left-hand main beam.
12* 10 A Right-hand main beam.
13* 15 A Horn.
14 10 A Front screenwash pump.
15* 30 A Ignition coil - Windscreen wiper - Oxygen sensor - Oil pressure - Injection system.
16* 30 A Air pump and oil temperature - Oil level - Brake lights operation - Alternator -
Water in diesel detector - Injection relay control.
17* 30 A Passenger electric seat.
18 40 A Heater blower - Starter - Windscreen wiper slow speed.
* The maxi-fuses provide additional protection for the electrical systems. All work must be carried out by a
PEUGEOT dealer.