2004 Peugeot 406 C Dag ignition

02-02-2004
Main menu Switch on the ignition. Press the "Menu"button to access the main menu.
Select a function using the direction arrows, then confirm ( "VAL" button). The
"Navigation/guidance" menu offers the following options:
Ð entering of the address of a new destination,
Ð selection of a service (Hotel, station, airport...) available in a town,
Ð selection of an address stored in one of the two directories,
Ð access to the "Navigation options" menu.
Ð radio functions are suspended when the system is in guidance mode.
YOUR 406 COUPE IN DETAIL 77
Navigation/Guidance Following selection of the "Navigation/guidance"menu,
a screen warns you about the use of the navigation sys- tem. Follow the regulations in force and do not use theremote control while driving. Press the "VAL"button to access the next screen.

Electrical adjustment of the front seats
A - Forwards-backwards adjustmentPush the switch forwards or backwards to slide the seat.
B - Adjusting the seat cushion angle Tilt the front part of the switch up or down.
C - Adjusting the driver's seat height Push the switch up or down.
D - Seat back angle adjustment Tilt the switch forwards or backwards
E - Tilting the seat back Pull the lever and tilt the seat back forwards. As long as you hold the seat back in the tilted position, the seat moves forward automatically (when the dooris closed, the ignition must be switched on in order tomove the seat forwards). On repositioning, the seat resumes its original settings.
YOUR 406 COUPE IN DETAIL
94
02-02-2004

02-02-2004
Recalling a memorised position
¥ Door open and ignition off Within ten minutes of switching off
the ignition and opening the door, ashort press on button 1or 2recalls
the memorised position of the seat,then of the exterior mirrors.
¥ Door closed or ignition on:
Ð keeping the button pressedadjusts the seat and the exteriormirrors.
When adjustment is completed ableep will sound.
YOUR 406 COUPE IN DETAIL 95
Memorising the seat and mirror positions
Two driving positions can be memo- rised.
To memorise:
Ð place the ignition key in the acces- sories position;
Ð adjust your seat and mirrors;
Ð simultaneously press button " M"
and button " 1" for the first driving
position or button " 2" for the
second driving position. When the position has been memorised, you will hear twobleeps. Memorising a new position cancels the previous one. Heated seat controls Press the switch.The temperature is controlled auto-
matically. Pressing a second time stops opera- tion.

02-02-2004
SEAT BELTS
To adjust the height of the front seat belts Pinch control 1and slide it.
To lock the seat beltsPull the strap, then insert the buckle into the stalk. Pre-tensioning and force-limitingfront seat belts Safety in the event of a frontal impact has been improved by the introduc-tion of pre-tensioning and force-limit-ing front seat belts. Depending onthe seriousness of the impact, thepre-tensioning system instantly tight-ens the seat belt firmly against thebody of the occupant. The pre-tensioning seat belts are active when the ignition is on. The force-limiting device reduces the pressure of the seat belt against theoccupant's body in the event of anaccident. Rear seat belts The rear seats are fitted with two three-point inertia reel belts.
YOUR 406 COUPE IN DETAIL
101
To be effective, a seat belt must be tightened asclose to the body as pos-sible.
Depending on the nature and theseriousness of the impact, thepre-tensioners may be triggeredbefore and independently of theair bags. In all cases, the air bag warning light comes on. Following a collision, have the system checked by a PEUGEOT
dealer.

02-02-2004
THE KEYS The keys allow you to switch on the ignition and to independently operatethe locks on the doors, the fuel fillercap, the glove box and the passen-ger air bag disarming switch. Central locking From the doors the keys allow you to lock, deadlock, close the windowskeeping the key in the lock, in thelocking position, for a few secondsand unlock the doors and the boot. If one of the front doors or the boot is open, central locking is not possible.An audible signal indicates this whenlocking by remote control. The remote control performs the same functions at a distance,except automatic closing of thewindows.The remote control Deadlocking Deadlocking renders the internal and external door controls inoperative. Press button
Ato deadlock the vehicle.
This is confirmed by fixed lighting of the direction indicators for approxi-mately two seconds. Another press on button A, within five
seconds of deadlocking, changes this to normal locking .
This is confirmed by fixed lighting ofthe direction indicators for approxi-mately two seconds. Unlocking Press button Bto unlock the vehicle.
This is confirmed by rapid flashing of the direction indicators. Note:
avoid handling the button of
your remote control when out of
range of your vehicle. You run therisk of stopping it from working. Itwould then be necessary to reini-tialise the remote control.
Locating your vehicle
To locate your vehicle, if you have locked it, in a car park:  press button A, the courtesy lights
come on and the direction indica-tors flash for a few seconds.
Key in ignition
A buzzer sounds on opening the dri-
ver's door, if the key has been left inthe ignition.
YOUR 406 COUPE IN DETAIL
84

02-02-2004
YOUR 406 COUPE IN DETAIL85
Changing the battery of the remote control The information
"battery flat"is
given by an audible signal accompa- nied by a message on the multi-func-
tion display.
To replace the battery, unclip the
casing using a coin at the ring(CR 2016/3 volt battery).If the remote control does not work after the battery has been changed,reprogramme the remote control.
Confidential card The confidential card contains the identification code necessary for anywork carried out by a PEUGEOTdealer on the electronic immobiliser
system. This code is hidden by afilm, which should be removed only if
necessary. Keep your card in a safe place, never inside the vehicle.
Programming the remote con- trol
 Switch off the ignition.
 Switch the ignition on again.
 Press button Aimmediately for a
few seconds.
 Switch off the ignition and remove the remote control key from the
ignition lock. The remote controlis now working again.
ELECTRONIC ENGINE IMMOBILISER This locks the engine management system as soon as the ignition has
been switched off and therefore pre-vents starting of the vehicle by any-
one who does not have the key. The ignition key has an electronic chip which has a special code. Whenthe ignition is switched on, the code is recognised and starting ispossible. If the system does not function correctly
, contact a PEUGEOT
dealer as soon as possible.

02-02-2004
YOUR 406 COUPE IN DETAIL
86
Make a careful note of the number on each key. The key number is coded on the label attached to the key. If the keys are lost, your PEUGEOT dealer can rapidly supply you with new keys.The high frequency remote control is a sensitive system; do not operate it while it is in your pocket as there is a
possibility that it may unlock your vehicle, without you being aware of it.The remote control does not operate when the key is in the ignition, even when the ignition is switched off, except for reprogramming. Do not operate the deadlocking function if there is anyone inside the vehicle.Driving with the doors locked may make access to the passenger compartment by the emergency services more difficult
in an emergency. As a safety precaution (with children on board), remove the ignition key when you leave the vehicle, even for a short time.
Do not repeatedly press the button of your remote control out of range of your vehicle. You run the risk of stopping it from working and the remote control would have to be reprogrammed. When purchasing a second-hand vehicle: - ensure that you are given the confidential card;
- have the key codes memorised by a PEUGEOT dealer, to ensure that the keys in your possession are the only ones which can start the vehicle.
Do not make any modifications to the electronic engine immobiliser system.

02-02-2004
YOUR 406 COUPE IN DETAIL85
Changing the battery of the remote control The information
"battery flat"is
given by an audible signal accompa- nied by a message on the multi-func-
tion display.
To replace the battery, unclip the
casing using a coin at the ring(CR 2016/3 volt battery).If the remote control does not work after the battery has been changed,reprogramme the remote control.
Confidential card The confidential card contains the identification code necessary for anywork carried out by a PEUGEOTdealer on the electronic immobiliser
system. This code is hidden by afilm, which should be removed only if
necessary. Keep your card in a safe place, never inside the vehicle.
Programming the remote con- trol
 Switch off the ignition.
 Switch the ignition on again.
 Press button Aimmediately for a
few seconds.
 Switch off the ignition and remove the remote control key from the
ignition lock. The remote controlis now working again.
ELECTRONIC ENGINE IMMOBILISER This locks the engine management system as soon as the ignition has
been switched off and therefore pre-vents starting of the vehicle by any-
one who does not have the key. The ignition key has an electronic chip which has a special code. Whenthe ignition is switched on, the code is recognised and starting ispossible. If the system does not function correctly
, contact a PEUGEOT
dealer as soon as possible.