2004 MITSUBISHI L200 instrument cluster

INSTRUMENTS AND CONTROLS
4-12
Combination headlamps,
dipper and turn signal
switch
EE11AAMb
Headlamps
Rotate the switch to turn on the lamps.
- All lamps off
- Position, tail, licence-plate, and in-
strument panel lamps on
- Headlamps on and other lamps go
on
NOTE
[Vehicles with Dim Dip]
When the ignition key is in the “ON” posi-
tion and the lamp switch is set to the
“ ” position, the low beam of the head-
lamp will illuminate dimly.
Dipper (High/Low beam change)
EE11B-Dd
When the lamp switch is in the “ ” posi-
tion, the beam changes from high to low
(or low to high) each time the lever is
pulled to (1). While the high beam is on,
the high beam indication lamp in the in-
strument cluster will also illuminate.
[Vehicles with Daytime Running Lamp]
When the ignition key is in the “ON” posi-
tion and the lamp switch is set to the “ ”
position, the low beam of the headlamps,
tail lamps, etc., will illuminate.
Lamp monitor system
If the driver’s door is opened when the key
is in the “LOCK” or “ACC” position or re-
moved from the ignition switch with the
lamp switch in the “ ” or “ ” position,
a buzzer will sound to remind the driver to
turn off the lamps.
Turn of the lamp switch, and the buzzer
will stop.
NOTE
(1) Do not leave the headlamps and
other lamps on for too long while the
engine is stationary. A run-down bat-
tery could result.
(2) When it rains, or when the vehicle has
been washed, the inside of the lens
sometimes becomes foggy. This is the
same phenomenon as when window
glass mists up on a humid day, and
does not indicate a functional prob-
lem. When the lamp is switched on,
the heat will remove the fog. However,
if water gathers inside the lamp,
please go to an authorized MIT-
SUBISHI dealer for a check.
E11A015E11C013
12
04engL2_240082_4 22-01-2004 13:20 Page 4-12

INSTRUMENTS AND CONTROLS
4-13 Headlamp flasher
EE11C-Fb
The headlamps flash when the lever is
pulled slightly to (2), and will go off when it
is released.
When the high beam is on, the high beam
indication lamp in the instrument cluster
will also illuminate.
NOTE
The headlamps can also flash when the
lamp switch is OFF.
Turn/lane-change signalsEE11D-Ag
The turn-signal lamps flash when the
switch is operated (with the ignition switch
“ON”). At the same time, the turn-signal
indicator flashes.
1 - Turn-signals
When making a normal turn, use posi-
tion (1). The lever will return automat-
ically when cornering is completed.
There are times when the lever will
not return after cornering. This occurs
when the steering wheel is turned
only slightly. In such cases, return the
lever by hand.
2 - Lane-change signals
When changing lanes, use position
(2). It will return to the neutral position
when released.NOTE
If the lamp flashes unusually quickly, the
bulb in a turn-signal lamp may have failed.
Have the vehicle inspected by an autho-
rized MITSUBISHI dealer.
E11D009
1
2
2
1
04engL2_240082_4 22-01-2004 13:20 Page 4-13

INSTRUMENTS AND CONTROLS
4-18
Hazard warning flasher
switch
EE16A-Dd
Use the hazard warning flasher switch
when the vehicle has to be parked on the
road for any emergency.
The hazard warning flashers can always
be operated, regardless of the position of
the ignition key.
Push the switch to turn on the hazard
warning flashers; push the switch again to
turn them off.
When this switch is operated, all turn-sig-
nal lamps flash continuously, as do the
turn-signal indication lamps in the instru-
ment cluster.
Rear window demister
switch*
EE17ABAa
The rear window demister switch can be
operated with the ignition switch in the
“ON” position.
Push the switch to turn on the rear window
demister.
To turn off the demister, press the switch
once again.
If your vehicle is equipped with the rear
window demister timer, this will be turned
off automatically in about 11 minutes.
To turn off the demister within 11 minutes,
push the switch again.
The indication lamp (A) will illuminate
while the demister is on.
If your vehicle is equipped with heated
mirrors, these operate in conjunction with
the demister.
CAUTION
If the lamps are kept flashing for a
long time, the battery will be dis-
charged, resulting in hard engine
starting or a no starting at all.
E17A025
A
E16A026
04engL2_240082_4 22-01-2004 13:20 Page 4-18