2004 MITSUBISHI ENDEAVOR belt

ohms in each wire, go to next step. If resistance is more than 2 ohms in either
wire, replace wire harness. Go to next step.
4. Reconnect all SRS components. Activate air bag system. Using scan tool, erase
then retrieve DTCs. If DTC 25 is retrieved, go to step 1 . If DTC 25 is not
retrieved, system is normal at this time. Intermittent condition may exist.
DTC 26: DRIVER-SIDE SEAT BELT PRETENSIONER SHORT CIRCUIT 1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS
. Disable SRS.
See DISABLING & ACTIVATING AIR BAG SYSTEM
. If DTC 34 is
retrieved, go to next step. If DTC 34 is not retrieved, go to step 3 .
2. Inspect SRS ECU connector C-25. See SRS ELECTRONIC CONTROL
UNIT (SRS ECU)
under REMOVAL & INSTALLATION. See Fig. 19
. If
connector is connected properly, go to next step. If connector is not connected
properly, connect properly and go to step 7 .
3. Disconnect negative battery cable. Disconnect, then reconnect SRS ECU
connector C-25 and driver-side seat belt pretensioner connector D-24. See
SEAT BELT PRETENSIONER
under REMOVAL & INSTALLATION.
Connect negative battery cable. Using scan tool, check for DTCs. If DTC 26 is
retrieved, go to next step. If DTC 26 is not retrieved, system is normal at this
time.
4. Disconnect negative battery cable. Connect Load Resistor (MB991865) to
Resistor Harness (MB991884). Connect resistor harness to driver-side seat belt
pretensioner connector D-24. Connect negative battery cable. Using scan tool,
check for DTCs. If DTC 26 is retrieved, go to next step. If DTC 26 is not
retrieved, replace driver-side seat belt pretensioner.
5. Disconnect SRS ECU connector C-25 and driver-side seat belt connector D-24.
Insert a cable tie or similar insulator between terminals No. 29 (Red/Blue wire)
and No. 30 (Red/Yellow wire) of SRS ECU connector to release shorting bar.
See Fig. 21
. If continuity exists between terminals No. 29 and 30, go to next
ste
p. If continuit
y does not exist, between terminals No. 29 and 30, erase, then
NOTE: Ensure shorting bar in SRS ECU connector is released by
using a cable tie or similar non conducting item to release
shorting bar before performing electrical measurements.
2004 Mitsubishi Endeavor Limited
2004 ACCESSORIES/SAFETY EQUIPMENT Mitsubishi - Air Bag Restraint Systems

retrieve DTCs using scan tool. If DTC 26 is retrieved, replace SRS ECU. Go to
step 7 .
6. Measure continuity of Red and Red/White wires between SRS ECU connector
C-25, terminals No. 29 and 30 and driver-side seat belt pretensioner connector
D-26, terminals No. 1 and 2. See Fig. 25
. If continuity does not exist in both
wires, replace wire harness between driver-side seat belt pretensioner and SRS
ECU. Go to next step. If continuity exists in both wires, go to next step.
7. Reconnect all SRS components. Activate air bag system. Using scan tool, erase
then retrieve DTCs. If DTC 26 is retrieved, go to step 1 . If DTC 26 is not
retrieved, system is normal at this time. Intermittent condition may exist.
Fig. 25: Identifying Seat Belt Pretensioner Connector D
-24 & D
-32 Terminals

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
DTC 27: DRIVER-SIDE SEAT BELT PRETENSIONER OPEN CIRCUIT 1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS
. Disable SRS.
See DISABLING & ACTIVATING AIR BAG SYSTEM
. Go to next ste
p.
NOTE: Ensure shorting bar in SRS ECU connector is released by
using a cable tie or similar non conducting item to release
shorting bar before performing electrical measurements.
2004 Mitsubishi Endeavor Limited
2004 ACCESSORIES/SAFETY EQUIPMENT Mitsubishi - Air Bag Restraint Systems

2. Disconnect driver-side seat belt pretensioner connector D-24. See SEAT
BELT PRETENSIONER
under REMOVAL & INSTALLATION. See Fig.
19 . Connect Load Resistor (MB991865) to Resistor Harness (MB991884).
Connect resistor harness to driver-side seat belt pretensioner connector.
Connect negative battery cable. Using scan tool, check for DTCs. If DTC 27 is
retrieved, go to next step. If DTC 27 is not retrieved, replace driver-side seat
belt pretensioner.
3. Disconnect SRS ECU connector C-25. See SRS ELECTRONIC CONTROL UNIT (SRS ECU)
under REMOVAL & INSTALLATION. Measure
resistance of Red/Blue wire between SRS ECU connector C-25, terminal No.
29 and driver-side seat belt pretensioner connector D-26, terminal No. 1. See
Fig. 21
& Fig. 25
. Measure resistance of Red/Yellow wire between SRS ECU
connector terminal No. 30 and driver-side seat belt pretensioner connector D-
26, terminal No. 2. If resistance is 2 ohms or less in both wires, erase, then
retrieve DTCs using scan tool. If DTC 27 is retrieved, replace SRS ECU. Go to
next step. If resistance is more than 2 ohms in either wire, replace wire harness
between SRS ECU and seat belt pretensioner. Go to next step.
4. Reconnect all SRS components. Activate air bag system. Using scan tool, erase
then retrieve DTCs. If DTC 27 is retrieved, go to step 1 . If DTC 27 is not
retrieved, system is normal at this time. Intermittent condition may exist.
DTC 28: PASSENGER-SIDE SEAT BELT PRETENSIONER SHORT CIRCUIT 1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS
. Disable SRS.
See DISABLING & ACTIVATING AIR BAG SYSTEM
. If DTC 34 is
retrieved, go to next step. If DTC 34 is not retrieved, go to step 3 .
2. Inspect SRS ECU connector C-25. See SRS ELECTRONIC CONTROL
UNIT (SRS ECU)
under REMOVAL & INSTALLATION. See Fig. 19
. If
connector is connected properly, go to next step. If connector is not connected
properly, connect properly. Go to step 7 .
3. Disconnect ne
gative batter
y cable. Disconnect SRS ECU connector
C-25 and
NOTE: Ensure shorting bar in SRS ECU connector is released by
using a cable tie or similar non conducting item to release
shorting bar before performing electrical measurements.
2004 Mitsubishi Endeavor Limited
2004 ACCESSORIES/SAFETY EQUIPMENT Mitsubishi - Air Bag Restraint Systems

passenger-side seat belt pretensioner connector D-32. See SEAT BELT PRETENSIONER
under REMOVAL & INSTALLATION. Reconnect
connectors. Connect negative battery cable. Using scan tool, check for DTCs.
If DTC 28 is retrieved, go to next step. If DTC 28 is not retrieved, system is
normal at this time.
4. Disconnect negative battery cable. Connect Load Resistor (MB991865) to
Resistor Harness (MB991884). Connect resistor harness to driver-side seat belt
pretensioner connector D-32. Connect negative battery cable. Using scan tool,
check for DTCs. If DTC 28 is retrieved, go to next step. If DTC 28 is not
retrieved, replace passenger-side seat belt pretensioner.
5. Disconnect SRS ECU connector C-25 and passenger-side seat belt connector
D-32. Insert a cable tie or similar insulator between terminals No. 27 (Red
wire) and 28 (Red/White wire) of SRS ECU connector to release shorting bar.
See Fig. 21
. Check for continuity between terminals. If continuity exists, go to
next step. If continuity does not exist, erase, then retrieve DTCs using scan
tool. If DTC 28 is retrieved, replace SRS ECU. Go to step 7 .
6. Measure continuity of Red and Red/White wires between SRS ECU connector
C-25, terminals No. 27 and 28 and passenger-side seat belt pretensioner
connector D-39, terminals No. 1 and 2. See Fig. 25
. If continuity does not
exist in both wires, replace wire harness between SRS ECU and passenger-side
seat belt pretensioner. Go to next step. If continuity exists in both wires, go to
next step.
7. Reconnect all SRS components. Activate air bag system. Using scan tool, erase
then retrieve DTCs. If DTC 28 is retrieved, go to step 1 . If DTC 28 is not
retrieved, system is normal at this time. Intermittent condition may exist.
DTC 29: PASSENGER-SIDE SEAT BELT PRETENSIONER OPEN CIRCUIT 1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS
. Disable SRS.
See DISABLING & ACTIVATING AIR BAG SYSTEM
. Go to next step.
2. Disconnect
passen
ger-side seat belt
pretensioner connector D-32. See SEAT
NOTE: Ensure shorting bar in SRS ECU connector is released by
using a cable tie or similar non conducting item to release
shorting bar before performing electrical measurements,
2004 Mitsubishi Endeavor Limited
2004 ACCESSORIES/SAFETY EQUIPMENT Mitsubishi - Air Bag Restraint Systems

BELT PRETENSIONE
R under REMOVAL & INSTALLATION. See Fig.
19 . Connect Load Resistor (MB991865) to Resistor Harness (MB991884).
Connect resistor harness to passenger-side seat belt pretensioner connector.
Connect negative battery cable. Using scan tool, check for DTCs. If DTC 29 is
retrieved, go to next step. If DTC 29 is not retrieved, replace passenger-side
seat belt pretensioner. Go to step 4 .
3. Disconnect SRS ECU connector C-25. See SRS ELECTRONIC CONTROL UNIT (SRS ECU)
under REMOVAL & INSTALLATION. Measure
resistance of Red wire between SRS ECU connector C-25, terminal No. 27 and
driver-side seat belt pretensioner connector D-32, terminal No. 1. See Fig. 25
.
Measure resistance of Red/White wire between SRS ECU connector terminal
No. 28 and driver-side seat belt pretensioner connector D-32, terminal No. 2. If
resistance is 2 ohms or less in both wires, erase, then retrieve DTCs using scan
tool. If DTC 29 is retrieved, replace SRS ECU. If resistance is more than 2
ohms in either wire, replace wire harness between SRS ECU and seat belt
pretensioner.
4. Reconnect all SRS components. Activate air bag system. Using scan tool, erase
then retrieve DTCs. If DTC 29 is retrieved, go to step 1 . If DTC 29 is not
retrieved, system is normal at this time. Intermittent condition may exist.
DTC 31 & 32: SRS ECU CAPACITOR If DTC 31 or 32 is present, replace SRS ECU. See SRS ELECTRONIC CONTROL UNIT (SRS ECU)
under REMOVAL & INSTALLATION.
DTC 34: SRS ECU CONNECTOR LOCK CIRCUIT 1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS
. Check SRS-
ECU connectors C-25 and C-26. See SRS ELECTRONIC CONTROL UNIT
(SRS ECU)
under REMOVAL & INSTALLATION. See Fig. 19
. If
connectors are connected properly, go to next step. If connectors are not
connected properly, connect properly. Go to step 3 .
2. Disconnect and inspect connectors C-25 and C-26. If connectors are damaged,
replace wire harness. Go to next step. If connectors are not damaged, reconnect
connectors. Using scan tool, erase then retrieve DTCs. If DTC 34 is retrieved,
re
place SRS ECU. Go to next ste
p.

2004 Mitsubishi Endeavor Limited
2004 ACCESSORIES/SAFETY EQUIPMENT Mitsubishi - Air Bag Restraint Systems

If DTC 54 or 55 is present, replace SRS ECU. See SRS ELECTRONIC CONTROL UNIT (SRS ECU)
under REMOVAL & INSTALLATION.
DTC 56 & 57: DRIVER-SIDE SEAT BELT PRETENSIONER If DTC 56 or 57 is present, replace SRS ECU. See SRS ELECTRONIC CONTROL UNIT (SRS ECU)
under REMOVAL & INSTALLATION.
DTC 58 & 59: PASSENGER-SIDE SEAT BELT PRETENSIONER If DTC 58 or 59 is present, replace SRS ECU. See SRS ELECTRONIC CONTROL UNIT (SRS ECU)
under REMOVAL & INSTALLATION.
DTC 61: DRIVER-SIDE AIR BAG MODULE SHORT TO VOLTAGE 1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS
. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM
. Go
to next step.
2. Disconnect clockspring connector C-305. See DRIVER
-SIDE AIR BAG
MODULE & CLOCKSPRING
under REMOVAL & INSTALLATION. See
Fig. 19
. Connect Load Resistor (MB991865) to Load Resistor Harness
(MB991866). Connect load resistor harness to clockspring connector C-305 by
backprobing connector. Connect negative battery cable. Using scan tool, check
for DTCs. If DTC 61 is retrieved, go to next step. If DTC 61 is not retrieved,
replace driver-side air bag module. Go to step 5 .
3. Disconnect negative battery cable. Disconnect clockspring connector C-307.
Connect load resistor and load resistor harness to clockspring connector C-307,
terminals No. 3 and 4 by backprobing connector. See Fig. 24
. Connect
negative battery cable. Using scan tool check for DTCs. If DTC 61 is retrieved,
go to next step. If DTC 61 is not retrieved, replace clockspring. Go to step 5 .
4. Disconnect SRS ECU connector C-26. Disconnect clockspring connector C-
307. Turn ignition on. Measure voltage between ground and SRS ECU
connector C-26, terminal No. 11 (Yellow/Black wire) and No. 12 (Yellow
wire). If voltage is measured at either terminal, replace wire harness. Go to
next step. If voltage is not measured, reconnect SRS components. Using scan
tool, erase then retrieve DTCs. If DTC 61 is retrieved, replace SRS ECU. Go to
next ste
p. If DTC 61 is not retrieved,
go to next ste
p.

2004 Mitsubishi Endeavor Limited
2004 ACCESSORIES/SAFETY EQUIPMENT Mitsubishi - Air Bag Restraint Systems

3. Reconnect all SRS components. Activate air bag system. Using scan tool, erase
then retrieve DTCs. If DTC 65 is retrieved, go to step 1 . If DTC 65 is not
retrieved, system is normal at this time. Intermittent condition may exist. DTC 66: DRIVER-SIDE SEAT BELT PRETENSIONER SHORT TO VOLTAGE 1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS
. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM
. Go
to next step.
2. Disconnect driver-side seat belt pretensioner connector D-24. See SEAT
BELT PRETENSIONER
under REMOVAL & INSTALLATION. See Fig.
19 . Connect Load Resistor (MB991865) to Load Resistor Harness
(MB991884). Connect load resistor harness to connector D-24. Connect
negative battery cable. Using scan tool, erase then retrieve DTCs. If DTC 66 is
retrieved, go to next step. If DTC 66 is not retrieved, replace driver-side seat
belt pretensioner. Go to step 4 .
3. Turn ignition off. Disconnect SRS ECU connector C-25. See SRS ELECTRONIC CONTROL UNIT (SRS ECU)
under REMOVAL &
INSTALLATION. Remove load resistor harness from driver-side seat belt
pretensioner connector D-24. Turn ignition on. Measure voltage between
ground and SRS ECU connector C-25, terminal No. 29 (Red/Blue wire) and
No. 30 (Red/Yellow wire). If voltage is measured at either terminal, replace
wire harness between SRS ECU and seat belt pretensioner. Go to next step. If
voltage is not measured at either terminal, reconnect SRS components. Using
scan tool, erase then retrieve DTCs. If DTC 66 is retrieved, replace SRS ECU.
Go to next step.
4. Reconnect all SRS components. Using scan tool, check for DTCs. If DTC 66 is
retrieved, go to step 1 . If DTC 66 is not retrieved, system is normal at this
time. Intermittent condition may exist.
DTC 67: DRIVER-SIDE SEAT BELT PRETENSIONER SHORT TO GROUND 1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS
. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM
. Go
to next step.
2. Disconnect drive
r-side seat belt
pretensioner connector D-24. See SEAT

2004 Mitsubishi Endeavor Limited
2004 ACCESSORIES/SAFETY EQUIPMENT Mitsubishi - Air Bag Restraint Systems

BELT PRETENSIONE
R under REMOVAL & INSTALLATION. See Fig.
18 . Connect Load Resistor (MB991866) to Load Resistor Harness
(MB991884). Connect Load Resistor Harness to connector D-24. Connect
negative battery cable. Using scan tool, erase then retrieve DTCs. If DTC 67 is
retrieved, go to next step. If DTC 67 is not retrieved, replace driver-side seat
belt pretensioner. Go to step 4 .
3. Disconnect SRS ECU connector C-25. See SRS ELECTRONIC CONTROL UNIT (SRS ECU)
under REMOVAL & INSTALLATION. Remove load
resistor harness from driver-side seat belt pretensioner connector D-24.
Measure continuity between ground and SRS ECU connector C-25, terminal
No. 29 (Red/Blue wire) and No. 30 (Red/Yellow wire). If continuity is not
found in either circuit, erase then retrieve DTCs. If DTC 67 is retrieved,
replace SRS ECU. Go to next step. If continuity is found in either circuit,
replace wire harness between SRS ECU and driver-side seat belt pretensioner.
Go to next step.
4. Reconnect all SRS components. Using scan tool, check for DTCs. If DTC 67 is
retrieved, go to step 1 . If DTC 67 is not retrieved, system is normal at this
time. Intermittent condition may exist.
DTC 68: PASSENGER-SIDE SEAT BELT PRETENSIONER SHORT TO VOLTAGE 1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS
. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM
. Go
to next step.
2. Disconnect passenger-side seat belt pretensioner connector D-32. See SEAT
BELT PRETENSIONER
under REMOVAL & INSTALLATION. See Fig.
16 . Connect Load Resistor (MB991865) to Load Resistor Harness
(MB991884). Connect load resistor harness to connector D-32. Connect
negative battery cable. Using scan tool, erase then retrieve DTCs. If DTC 68 is
retrieved, go to next step. If DTC 68 is not retrieved, replace passenger-side
seat belt pretensioner. Go to step 4 .
3. Disconnect SRS ECU connector C-25. See SRS ELECTRONIC CONTROL UNIT (SRS ECU)
under REMOVAL & INSTALLATION. Remove load
resistor harness from connector D-32. Turn ignition on. Measure voltage
between ground and SRS ECU connector
C-25, terminal No. 27 (Red wire)

2004 Mitsubishi Endeavor Limited
2004 ACCESSORIES/SAFETY EQUIPMENT Mitsubishi - Air Bag Restraint Systems