Page 1867 of 3870
1. Install special tool MB991897 as shown in the figure.
Fig. 16: Installing Special Tool MB991897
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Turn the bolt and knob as necessary to make the jaws of special tool
MB991897 parallel, tighten the bolt by hand and confirm that the jaws are still
parallel.
3. Tighten the bolt with a wrench to disconnect the tie rod end and remove the
self lockin
g nut.
NOTE: When adjusting the jaws in parallel, make sure the knob
is in the position shown in the figure.
2004 Mitsubishi Endeavor LS
2004 DRIVELINE/AXLES Front Axle Hub & Axle Shafts - Endeavor
Page 1974 of 3870
Page 1975 of 3870
Fig. 32: Installing Special Tool MB991897
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Turn the bolt and knob as necessary to make the jaws of special tool
MB991897 parallel, tighten the bolt by hand and confirm that the jaws are still
parallel.
Fig. 33: Using Special Tool MB991897
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
3. Tighten the bolt with a wrench to disconnect the tie rod end.
REMOVAL SERVICE POINT <> STEERING GEAR AND STEERING COLUMN SHAFT DISCONNECTION
NOTE: When adjusting the jaws in parallel, make sure the knob
is in the position shown in the figure.
2004 Mitsubishi Endeavor LS 2004 SUSPENSION Front - Endeavor
Page 1976 of 3870
1. Remove the steering gear and steering column shaft connecting bolt.
2. Pinch the steering column shaft clip with pliers, and pull up the shaft towards
the direction shown in illustration to disengage the steering column shaft from
the steering gear.
Fig. 34: Disengaging Steering Column Shaft From Steering Gear
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
NOTE: If the steering column shaft is removed accidentally,
remove the steering column assembly and be sure to
insert the steering column shaft into the steering
column as shown in the figure.
2004 Mitsubishi Endeavor LS 2004 SUSPENSION Front - Endeavor
Page 2000 of 3870
Fig. 1: A/C Compressor Clutch Relay On Conditioning Chart
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
SERVICE PRECAUTIONS CAUTION LABELS The refrigerant gas warning label must be affixed in the location shown in the
figure on the left. Follow the instructions on the label when servicin
g.
2004 Mitsubishi Endeavor LS
2004 HVAC Heater Air Conditioning, Ventilation - Endeavor
Page 2063 of 3870
Fig. 46: Connecting Special Tool (MB991658) To Harness Side
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
4. At this time, check to see that the voltage of A/C pressure sensor terminal
No.2 reflects the specifications of the figure.
Q: Is the A/C pressure sensor in good condition?
YES:
Go to Step 6.
NO:
Replace the A/C pressure sensor. Then go to Step 8 .
NOTE: The allowance shall be defined as +/-5%.
2004 Mitsubishi Endeavor LS
2004 HVAC Heater Air Conditioning, Ventilation - Endeavor
Page 2239 of 3870
Fig. 170: Identifying A/C Pressure Sensor Connector
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
3. Turn ON the engine and then turn ON the air conditioner switch.
4. At this time, check to see that the voltage of A/C pressure sensor terminal
No.2 reflects the specifications of the figure.
2004 Mitsubishi Endeavor LS
2004 HVAC Heater Air Conditioning, Ventilation - Endeavor
Page 2363 of 3870
Fig. 272: Connecting Special Tool (MB991658)
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
4. At this time, check to see that the voltage of A/C pressure sensor terminal No.2
reflects the specifications of the figure.
NOTE: The allowance shall be defined as +/-5%.
2004 Mitsubishi Endeavor LS
2004 HVAC Heater Air Conditioning, Ventilation - Endeavor
