2004 MERCEDES-BENZ ML350 Lock

93 Controls in detail
Locking and unlocking
Automatic central locking
The doors and the liftgate automatically
lock when the ignition is switched on and
the left front wheel turns at vehicle speeds
of approximately 9mph (15km/h) or
more.
If one of the front doors is then opened
from the inside, the vehicle is unlocked
centrally unless only the driver's door was
previously unlocked.Information on towing the vehicle can be
found in the “Practical hints” section
(
page 241).
The switch is located on the lower center
console.
Central locking switch1Locking
2UnlockingActivating

Make sure the ignition is switched on.
All the lamps in the instrument cluster
light up.

Press and hold upper part1 of the
central locking button for approximate-
ly six seconds.
The automatic central locking is
activated.
Deactivating

Make sure the ignition is switched on.
All the lamps in the instrument cluster
light up.

Press and hold lower part2 of the
central locking button for approximate-
ly six seconds.
The automatic central locking is deacti-
vated.
iThe doors unlock automatically after an
accident if the force of the impact ex-
ceeds a preset threshold.
To prevent the vehicle door locks from
locking, deactivate the automatic cen-
tral locking when the vehicle

is pushed or towed


is on a test stand

94 Controls in detailLocking and unlockingLocking and unlocking from the inside
You can lock or unlock the doors and the
tailgate from inside using the central lock-
ing switch. This can be useful, for example,
if you want to lock the vehicle before start-
ing to drive.Locking

Press upper part1 of central locking
button (
page 93).
If all the doors are closed, the vehicle
locks.
Unlocking

Press lower part2 of central locking
button (
page 93).
The vehicle unlocks.
Warning!
G
When leaving the vehicle, always remove the
key from the steering lock and lock the vehi-
cle. Do not leave children unattended in the
vehicle, or with access to an unlocked vehi-
cle. Unsupervised use of vehicle equipment
may cause an accident and / or serious per-
sonal injury.
iYou can open a locked door from the
inside. Open door only when conditions
are safe to do so.
If the vehicle was previously centrally
locked using the remote control, it will
not unlock using the central locking
switch.

99 Controls in detail
Seats
Switching off rapid seat heating
Press lower switch position2 again.
Both red indicator lamps on the switch
turn off.
Rear seats
The rear seats are divided asymmetrically.
To enlarge the cargo area you can adjust
the left and right part separately. The fol-
lowing changes are possible:

moving the seat fore and aft


folding down the backrest


lowering the seatAdjusting rear seat fore and aft
1Release lever

Pull release lever1 in direction of
arrow.

Slide seat to the desired position until
it locks in place.
!If one or both of the lamps on the seat
heater switch are flashing, there is in-
sufficient voltage available since too
many electrical consumers are turned
on. The seat heater switches off auto-
matically.
The seat heater will switch back on
again automatically as soon as suffi-
cient voltage is available.
Warning!
G
Do not adjust the rear seats while driving.
Always seat in an upright position and the
seat belts are properly positioned on the
body. Your seat must be adjusted so that
you can correctly fasten your seat belt.
Adjust head restraint to support the back of
the head approximately at ear level.
Never place hands under the seat or near
any moving parts while a seat is being ad-
justed.
Warning!
G
Failure to assure that seats are locked into
place could result in an increased chance of
injury in an accident.

100 Controls in detailSeatsFolding down the backrest
1Lock button
Close cup holder (
page 167) and
ashtray (
page 169) in rear center
console (page 167).

Move front seats forward. Manual seat
(page 35) or power seat (
page 37).

Slide seat forward.

Remove head restraint(s) (
page 95).

Pull lock button1 up and fold back-
rest forward until it locks in place.The red backrest lock indicator at lock
button1 is not visible in the locked
position.
Folding up the backrest

Close cup holder (
page 167) and
ashtray (
page 169) in rear center
console.

Pull lock button1 up and unfold back-
rest until it locks in place.
M a k e s u r e t h e s e a t b e l t i s n o t c a u g h t i n
the seat.

Check for secure locking by pulling and
pushing on the backrest.
The red backrest lock indicator at lock
button1 is not visible in the locked
position.

Install head restraint (
page 96).

Slide seat rearward to desired position
(page 99).

Adjust front seats to desired position.
Manual seats (
page 35) or power
seats (
page 37).
Lowering the rear seat
1Release button
2Lever
3Release lever

101 Controls in detailSeats

Close cup holder in rear center console
(page 167).

Move front seats forward. Manual seat
(page 35) or power seat (
page 37).

Press and hold release button1 to un-
lock lever2.

Pull lever2 in direction of arrow.

Pull release lever3 and push down
rear seat until it locks in place.

Fold down the backrest (
page 100).

Adjust front seats to desired position.
Manual seats (
page 35) or power
seats (
page 37).Folding up the rear seat

Move front seats forward. Manual seat
(page 35) or power seat (
page 37).

Pull release lever3 and raise rear seat
until it locks in place.
Easy entry / exit feature*
The easy entry / exit feature allows access
to the third row seats*. The right cargo
floor plate must be removed (
page 162).Folding rear seat forward
1Lever

Move right seat forward. Manual seats
(page 35) or power seats
(page 37).

Move rear seat forward (
page 99).

Push head restraint fully down and tilt
it forward.

Fold backrest forward (
page 100).

Pull lever1 up and fold the rear seat
forward.
Warning!
G
Failure to assure that seats are locked into
place could result in an increased chance of
injury in an accident.Warning!
G
Never drive with the second row right seat
folded forward (easy entry / exit feature). It
could open and fold back unintentionally.

102 Controls in detailSeatsResetting rear seat
Pull down on seat bench until it locks
into place.

Pull lock button1 (
page 100) up
and unfold backrest until it locks into
place.

Check for secure locking by pulling and
pushing on the backrest.
The red backrest lock indicator at lock
button1 (
page 100) is not visible in
the locked position.

Move the rear and front seats in de-
sired position.

Pull up and adjust head restraint
(page 36).
Third row seats*Folding down single seat
1Head restraint
2Hook
3Tensioner
4Hook and loop velcro strip

Remove cargo floor plate
(page 162).

Remove head restraint1 from seat
cushion.

Lift tensioner3 upward to a horizon-
tal position to release tension of the
belt.

Disengage hook2 while holding onto
the seat firmly with one hand.
Warning!
G
For your protection, drive only with properly
positioned head restraints.
Adjust head restraint so that head restraint
supports the back of the head at eye level.
This will reduce the potential for injury to the
head and neck in the event of an accident or
similar situation.
Failure to assure that seats are locked into
place could result in an increased chance of
injury in an accident.
Never place hands under seat or near any
moving parts while a seat is being adjusted.

103 Controls in detailSeats

Attach belt at hook and loop velcro
strip4 (
page 102) on underside of
seat.
5Backrest release
6Seat release

Fold seat down until it locks securely in
place.
The red marking on the seat release6
should not be visible.

Store cargo floor plates inside the
backrest (
page 162).

Pull backrest release5 and unfold
backrest until it locks securely in place.

Install head restraint1 in backrest
(page 102).
Storing single seat

Remove head restraint from backrest
(page 102).

Pull backrest release5 and fold back-
rest forward until it locks securely in
place.

Remove cargo floor plates from the
backrest.

Pull seat release6 (
page 103) and
fold seat up.

Disengage belt and engage hook2
(page 102) in ceiling mount.

Pull on free end of belt until tight.

Install head restraint in openings
provided in seat cushion.

Install cargo floor plates (
page 162).
Warning!
G
After folding the seats up, manually place
the lap belt portion of the seat belt behind
the seat (arrow). Otherwise, the lap belt may
be subject to damage and could rip.

109 Controls in detail
Lighting
Daytime running lamp mode
Canada only:
Turn combination switch to
positionM orU.
When the engine is running, the low beam
headlamps are automatically switched on.
In low ambient light conditions, the parking
lamps will also switch on.
When you shift from a driving position to
positionN orP, the low beam switches off
(three minutes delay).
For nighttime driving you should turn the
combination switch to positionõ to
permit activation of the high beam head-
lamps.Night security illumination
When you turn off the engine and the last
door has been closed, the following lamps
will remain lit:


Parking lamps


Tail lamps


License plate lamps


Front fog lamps
The combination switch must be set to
positionU (
page 107).Deactivating night security illumination
temporarily

Before leaving the vehicle, turn the key
in the steering lock to position0
(page 33) then turn it to position2
and back to0.
The night security illumination is deac-
tivated. It will reactivate as soon as you
start the engine.
Setting illumination time
1Switch for fog lamps
iThe high beam flasher is always avail-
able.
iYou can reactivate this function within
ten minutes by opening a door or the
liftgate.
If you do not open a door or the liftgate
after turning off the engine, the lamps
will automatically switch off after
60 seconds.