2004 MERCEDES-BENZ CLK320 CABRIOLET display

205 Controls in detail
Audio system
Phone book
The numbers stored in the phone book can
be called up either by name or number.
Calling up the phone book
Pressd, c, f or e but-
ton.Switching between name search and
number search

Press the
ABC
key.
The name search is called up.
or

Press the
NUM
key.
The number search is called up.
Searching and calling up phone book en-
tries by name

Press the
ABC
key.
The current name is highlighted on the
display.

Press either thed orc button.
The stored entries are selected accord-
ing to the alphabetical order of the ini-
tial letter.
or

Press either thef ore button.
The stored entries are selected in
increments of four.
or

Press the desired numerical key2 to
9.
The stored entries are selected accord-
ing to the alphabetical order of the ini-
tial letters (e.g. for B -Brown, press
button2 twice).iSeveral characters and symbols cannot
be shown on the display for technical
reasons. They have been replaced with
spaces.

206 Controls in detailAudio systemSearching and selecting phone book en-
tries by number
Press the
NUM
key.
The current number is marked in the
display.

Press either thed or cbutton.
The stored entries are selected
according to numerical order.
or

Press either thef or ebutton.
The stored entries are selected in
increments of 5 (e.g. Entry
M5, Entry
M10
,etc.)Starting dialing process

Once you have selected a number,
press the
SND
key.
Repeat dialing
If the number dialed is busy, you can again
place calls to the last ten telephone num-
bers dialed using the repeat dialing func-
tion.Manual repeat dialing (redial)

Press the
SND
key.
The last number dialed is shown in the
display.

Select the desired telephone number
usingd, c, f or
ebutton.
The abbreviation
L and the number of
the entry are shown in the top line of
the display.

When you have selected a number,
press the
SND
key.
The call will be made.

207 Controls in detail
Audio system
Automatic repeat dialing (redial)
If a call cannot be connected, press
the
SND
key.
REDIAL
will appear on the display and re-
peated attempts to place the call will be
made for the next four minutes.
Selecting numbers directly from the
directory

Enter previously selected 3-digit
(1-999) number of the entry using
number keys 4 to M.

Press the
RCL
key.
The telephone number stored under
that entry will be dialed.

Press the
SND
key.
The call will be made.Speed dialing

Input desired entry number using
number keys 4 to M.
A maximum of two digits can be en-
tered.
If necessary, correct the last number
entered with the
CLR
key.

Press the
SND
key.
The telephone number stored under
that entry will be dialed. The number,
L
and the full entry number will be shown
in the display.Quick-dialing

Press one of the desired number
buttons4 toM longer than one
second.
The telephone number saved under
that number will be dialed.!Please be aware that button 4
might already be reserved for an emer-
gency call number.

208 Controls in detailAudio systemEmergency call
Press button4 longer than one
second.

A call will be placed to the saved num-
ber (e.g. 911).
You can make an emergency call to an
emergency rescue station with a mobile
communications network.
The emergency call will be placed as long
as the corresponding mobile communica-
tions network is available. To do this,
switch the telephone on if this has not al-
ready been done.The call will also be placed even if the un-
lock code is not entered.
Emergency calls may not be possible with
all telephone networks or if certain net-
work services and/or telephone functions
are active. Check with your local network
operation company. It may take some time
to set up an emergency call.
To use this function you must ensure that
the number stored in memory location 1 is
the number to be dialed in case of emer-
gency.
If an emergency call cannot be connected,
the message
SYSTM BUSY
appears.Accepting an incoming call
Accepting an incoming call in telephone
mode
With an incoming call, a ringing tone can
be heard and the caller’s telephone num-
ber, or the name under which this tele-
phone number has been saved in the
telephone book, appears on the display. If
the caller’s number is not transmitted,
CALL
will appear in the display.

Press the
SND
key to accept call.
!Please be aware that the 911 emergen-
cy call system is a public service. Using
it without due cause is a criminal of-
fense.

209 Controls in detail
Audio system
Accepting an incoming call in cassette,
CD or radio mode
If the telephone is activated in the back-
ground (receiving symbol
S visible on dis-
play), the audio source is muted when a
call is received. The ringing tone is heard
and the caller’s telephone number or the
name under which this telephone number
has been saved in the telephone book ap-
pears on the display. If the caller’s number
is not transmitted,
CALL
appears in the dis-
play.

Press the
SND
key to accept the call.Muting a call
It is possible to mute a call; the caller is
then no longer able to hear you.
Mute on

Press the
MUT
key.
Mute off

Press the
MUT
key.
Terminating a call

Press the
END
key.
The current call is terminated.Call waiting
If you receive another call during an al-
ready active call, you can accept the sec-
ond call and switch between the two.
Accepting a second call

Press the
SND
key.
You are connected with the second
caller, the first call is muted.
Switching between the calls

Press the
SND
key.
Terminating the second call

Press the
END
key.
The current call will be terminated. You
are connected with the muted call
again.

218 Controls in detailSoft topOpening the soft topSoft top switch1Indicator lamp
2Soft top openingBefore pulling on the soft top switch, you
must make sure:


the parking brake is engaged
(page 46)


the luggage cover is latched, see
“Latch luggage cover” (
page 216)


the ski sack roller blind is closed, see
“Closing ski sack roller blind”
(page 217)


the trunk lid is closed


the ignition is switched on (SmartKey in
starter switch position2 or press the
KEYLESS-GO* start/stop button twice)

Pull up on the soft top switch as indi-
cated by the arrow2 until the soft top
is completely lowered into its trunk
storage compartment and the indicator
lamp1 in the soft top switch goes
out.
During the opening procedure the mul-
tifunction display shows the message Top in operation
.
If the opening procedure is finished,
the multifunction display will briefly
show the message Top open
.
If you continuously pull on the soft top
switch, the windows will close.
However, the windows can also be
closed/opened later on, for more informa-
tion see “Opening and closing the windows
with the soft top switch” (
page 212), or
see “Opening and closing the windows”
(
page 210)

220 Controls in detailSoft topBefore pressing the soft top switch, you
must make sure:

the parking brake is engaged
(page 46)


the trunk lid is closed


the ignition is switched on (SmartKey in
starter switch position2 or press the
KEYLESS-GO* start/stop button twice)

Press the soft top switch as indicated
by the arrow2 until the soft top is
completely closed and locked.The indi-
cator lamp1 in the soft top switch
goes out.
During the closing procedure the multi-
function display shows the message Top in operation
.
If the soft top is closed and locked, the
multifunction display will briefly show
the message
Top closed
.
If you continuously press on the soft
top switch the windows will close.However, the windows can also be
closed/opened later on, for more informa-
tion see “Opening and closing the windows
with the soft top switch” (
page 212) or
see “Opening and closing the windows”
(
page 210)Locking the soft top after raising/low-
ering
If the soft top is not properly locked, lock it
as described below.iFor safety reasons, the soft top cannot
be opened while driving.Warning!
G
To prevent possible accidents, drive the ve-
hicle only with the soft top either completely
closed and locked, or fully lowered into its
storage compartment.
Warning!
G
The soft top is not fully closed and locked or
not fully opened if:

the indicator lamp in the soft top switch
remains lit


the message
Top in operation!
is
shown in the multifunction display and
the indicator lamp in the soft top switch
does not go out


the indicator lamp flashes and a warning
sounds for 10 seconds and the message Lock top
is shown in the multifunction
display when starting to drive
To prevent possible accidents, drive the ve-
hicle only with the soft top either completely
closed and locked, or fully lowered into its
storage compartment.

221 Controls in detail
Soft top
Unlocked status noticed when stopped
Switch on the ignition.

To lock the soft top in its fully closed
position, press soft top switch.
The message
Top closed
will be shown
in the multifunction display.
or:

To lock the soft top in its fully opened
position, pull up on the soft top switch.
The message
Top open
will be shown in
the multifunction display.Unlocked status noticed while driving

Stop the vehicle.

Leave the ignition switched on.

To lock the soft top in its fully closed
position, press soft top switch.
The message
Top closed
will be shown
in the multifunction display.
or:

To lock the soft top in its fully opened
position, pull up on the soft top switch.
The message
Top open
will be shown in
the multifunction display.
Warning!
G
Stop the vehicle and lock the soft top before
continuing to drive. You could otherwise en-
danger yourself and others.
Warning!
G
If the soft top does not completely open or
close, the roof hydraulics will lose pressure
and the soft top is lowered

after approximately seven minutes
when the ignition is switched on


after approximately 15 seconds when
the ignition is switched off
Shortly before the soft top is lowered, a
warning will sound and the soft top switch
lamp will flash. In the multifunction display
you will see K, and the message
Top
being lowered!
appears


Properly lock the soft top (
page 220)
before continuing to drive