Page 312 of 400
312 Practical hintsReplacing bulbsReplacing bulbs for front lamps
Halogen headlamps
1Bulb socket for turn signal lamp
2Headlamp cover for high beam head-
lamp and for parking and standing
lamp
3Headlamp cover for low beam head-
lamp4Low beam bulb
5High beam bulb
6Bulb socket for parking and standing
lamp
Low and high beam bulb
Switch off the lights.
Open the hood (
page 252).
Press the clamp and remove headlamp
cover2 or3.
Pull electrical connector off.
Unclip the retainer springs and take out
the bulb.
Insert the new bulb so that the base
locates in the recess on the holder.
Clip the retainer springs and plug the
connector onto the bulb.
Align headlamp cover2 or3 and
click into place.
Front turn signal lamp bulb
Switch off the lights.
Open the hood (
page 252).
Twist bulb socket1 counterclockwise
and pull out.
Push bulb into socket, turn counter-
clockwise and remove.
Insert new bulb in socket, push in and
twist clockwise.
Reinsert bulb socket in lamp and twist
clockwise.
Page 313 of 400
313 Practical hints
Replacing bulbs
Parking and standing lamp bulb
Switch off the lights.
Open the hood (
page 252).
Press the clamp and remove headlamp
cover2.
Pull out bulb socket6 with the bulb.
Pull the bulb out of bulb socket.
Insert a new bulb in the socket.
Reinstall bulb socket.
Align headlamp cover2 and click into
place.Bi-Xenon* headlamps
1Bulb socket for turn signal lamp
2Headlamp cover for high beam flasher,
parking and standing lamp
3Cover for Bi-Xenon lamp4High beam flasher bulb
5Bayonet socket for high beam flasher
bulb
6Bulb socket for parking and standing
lamp
High beam bulb for high beam flasher
Switch off the lights.
Open the hood (
page 252).
Press the clamp and remove lamp
cover2.
Pull electrical connector4 off.
Warning!
G
Do not remove the cover3 for the
Bi-Xenon headlamp. Because of high voltage
in Bi-Xenon lamps, it is dangerous to replace
the bulb or repair the lamp and its compo-
nents. We recommend that you have such
work done by a qualified technician.
Page 314 of 400
314 Practical hintsReplacing bulbs
Twist bayonet socket5 counterclock-
wise to the stop (do not remove).
Pull the bulb out of the socket.
Insert the new bulb so that the base
locates in the recess in bayonet
socket5.
Twist bayonet socket clockwise until
you hear it snap into place.
Plug the connector onto the bulb.
Align lamp cover2 and click into
place.Front turn signal lamp bulb
Switch off the lights.
Open the hood (
page 252).
Twist bulb socket1 counterclockwise
and pull out.
Push bulb into socket, turn counter-
clockwise and remove.
Insert new bulb in socket, push in and
twist clockwise.
Reinsert bulb socket in lamp and twist
clockwise.Parking and standing lamp bulb
Switch off the lights.
Open the hood (
page 252).
Press the clamp and remove lamp
cover2.
Pull out bulb socket6 with the bulb.
Pull the bulb out of bulb socket.
Insert a new bulb in the socket.
Reinstall bulb socket.
Align lamp cover2 and click into
place.
Page 315 of 400
315 Practical hints
Replacing bulbs
Side marker lamp bulb
Switch off the lights.
Carefully slide lamp towards rear.
Remove front end first.
Twist bulb socket counterclockwise
and pull out.
Pull bulb out of the bulb socket.
Insert new bulb in socket.
Reinstall bulb socket, push in and twist
clockwise.
To reinstall lamp, set rear end in
bumper and let front end snap into
place.
Replacing bulbs for rear lamps
Tail lamp assemblies
Open tailgate (
page 87).
Switch off the lights.
Press button1 on the corresponding
side.
Fold down trim panel2.
Squeeze tabs together3.
Remove bulb holder.
Page 316 of 400
316 Practical hintsReplacing bulbs4Brake lamp
5Turn signal lamp
6Backup lamp
7Rear fog lamp (driver’s side)/tail lamp,
parking, standing and side marker
lamp
Gently push bulb into socket, turn
counterclockwise and pull out.
Insert new bulb and turn clockwise.
Reinstall bulb socket.
Reinstall bulb holder and close trim
panel.License plate lamp
1Screws
Switch off the lights.
Loosen both screws1 and remove
lamp.
Replace the tubular lamp and reinstall
lamp.
Retighten the screws.
Page 328 of 400
328 Practical hintsJump startingThe battery is located in the engine
compartment on the right hand side. The
terminals for jump starting are located in
front of the battery.
Make sure the two vehicles do not
touch.
Turn off all electrical consumers.
Apply parking brake.
Shift gear selector lever to positionP.1Positive terminal of charged battery
2Positive under hood terminal in front of
discharged battery
3Negative terminal of charged battery
4Negative under hood terminal in front
of discharged battery
Connect positive terminal1 of the
charged battery with positive under
hood terminal2 in front of the
discharged battery with the jumper
cables. Clamp cable to charged
battery1 first.
Start engine of the vehicle with the
charged battery and run at idle speed.
Connect negative terminal3 of the
charged battery with negative under
hood terminal4 in front of the
discharged battery with the jumper
cables. Clamp cable to charged
battery3 first.
Start the engine of the disabled
vehicle.
You can now again turn on the electrical
consumers. Do not turn on the lights under
any circumstances.
Remove the jumper cables first from
negative terminals3 and4 and then
from positive terminals1 and2.
You can now turn on the lights.
Have the battery checked at the near-
est authorized Mercedes-Benz Center.
Warning!
G
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety instructions and precau-
tions when handling automotive batteries
(page 258).
!Do not tow-start the vehicle.
