2004 MAZDA MODEL MX-5 MIATA buttons

6-38
Interior Comfort
Au di o S ys t em
Form No. 8S15-EA-03G

Antitheft System*
To deter theft of your vehicle
’s audio unit,
it has an integrated antitheft system. The
system is designed to accept a code
number that makes the unit inoperable if it
is stolen.
This system will be activated if the power
source is ever disconnected from or in any
way interrupted to the audio unit. When
the system is activated, the audio system
will not operate when reconnected to a
power supply, and "CODE" will flash on
the display until the correct code number
is input. If the antitheft system is
activated, reset the unit.
Display
Auto memory
button
Channel preset buttons
Antitheft indicator light
Read and understand all code setting
procedures before attempting to input
your personal code number.
The personal code number is only
shown on the audio unit display while
it is being set. Once it is input and
stored by the unit, it is never again
displayed. For that reason, be very
careful to immediately record your
personal code number, and never let an
unauthorized person set a code.
NOTE
Although the audio unit is operable
without the code number being set, we
recommend that you set your personal
code number.
CAUTION
*Some models.
J07S_8S15-EA-03G_Edition2.book Page 38 Thursday, August 21, 2003 10:04 AM

6-39
Interior Comfort
Au di o S ys t em
Form No. 8S15-EA-03G
Setting procedure
1. Begin with the audio unit off and the ignition switch is in the ACC position.
2. Press the auto memory button ( ) and the channel preset button 6
simultaneously for about 2 seconds
until "CODE" is displayed.
3. Again press the auto memory button ( ) and the channel preset button
6 simultaneously while "CODE" is
displayed (within 10 seconds). The
display will exhibit bars.
4. While the bars are displayed, input your personal code number by pressing
channel preset buttons 1, 2, 3, and 4. Press 1 for the first digit, 2 for the second,
3 for the third, and 4 for the last digit. For
example, if your number is 2547, press 1
three times, 2 six times, 3 five times, and 4
eight times. If the display goes off while
inputting, begin from Step 1.
5. While the code number is displayed,
press the auto memory button ( )
and the channel preset button 6
simultaneously for about 2 seconds and
"CODE" begins to flash. After about 5
seconds, "CODE" will disappear. This
indicates the system is set.
NOTE
We recommend that your code number
be associated with something easy to
remember. You should also file a copy
of the code numbers with your
important papers.
J07S_8S15-EA-03G_Edition2.book Page 39 Thursday, August 21, 2003 10:04 AM

6-46
Interior Comfort
Au di o S ys t em
Form No. 8S15-EA-03G

Operating the Radio
Radio ON
Press a band selector button ( or
) to turn the radio on.
Band selection
Choose AM by pressing the AM button
( ) and FM by pressing the FM1/2
button ( ).
The selected mode will be indicated. If
FM stereo is being received, "ST" will be
displayed. Tu n i n g
The radio has the following tuning
methods: Manual, Seek, Scan, Preset
channel, and Auto memory tuning. The
easiest way to tune stations is to set them
on preset channels.
Manual tuning
Turning the manual tuning dial will
change the frequency higher or lower.
Band selector buttons Display
Channel preset buttons
Scan button
Auto memory
button
Manual tuning dial Seek tuning
button
NOTE
If the FM broadcast signal becomes
weak, reception automatically changes
from STEREO to MONO for reduced
noise, and the "ST" indicator will go
out.
NOTE
If the power supply is interrupted (fuse
blows or the battery is disconnected),
the preset channels will be canceled.
J07S_8S15-EA-03G_Edition2.book Page 46 Thursday, August 21, 2003 10:04 AM

6-54
Interior Comfort
Au di o S ys t em
Form No. 8S15-EA-03G

Operating the In-Dash CD Changer*
Inserting the CD
The CD must be label-side up when
inserting. The auto-loading mechanism
will set the CD and begin play. There will
be a short lapse before play begins while
the player reads the digital signals on the
CD.
The disc number and the track number
will be displayed. Normal insertion
1. Press the load button ( ).
2. When "In" is displayed, insert the CD.
Inserting CDs into desired tray number
1. Press and hold the load button ( )
for about 2 seconds until a beep is
heard.
2. Press the channel preset button for the desired tray number within 3 seconds
after the beep is heard.
3. When "In" is displayed, insert the CD.
Disc-in indicator
CD ejectbutton
Scan
button Track up
button
Track down
button
Disc down
button
Load button
Random button
Repeat button
Disc up button Reverse button
Fast-forward
button
Channel preset buttons
Display
CD slot
CD play button
NOTE
A CD cannot be inserted while the
display reads "WAIT". A beeping
sound can be heard during this waiting
time. Simultaneously pressing the
power/volume dial and the load button
( ) for about 2 seconds will turn
this beeping sound ON or OFF.
NOTE
The CD cannot be inserted to the
desired tray number if the number is
already occupied.
*Some models.
J07S_8S15-EA-03G_Edition2.book Page 54 Thursday, August 21, 2003 10:04 AM