2004 MAZDA MODEL 6 ignition

6-24
Interior Comfort
Audio System
Form No. 8R29-EA-02I

Power/Volume/Sound Controls
Power ON/OFF
Turn the ignition switch to the ACC or
ON position.
Press the power/volume dial to turn the
audio system on.
Press the power/volume dial again to turn
the audio system off.Vo l u m e a d j u s t m e n tTo adjust the volume, turn the power/
volume dial.
Turn the power/volume dial to the right to
increase volume, to the left to decrease it.
Audio control dial Power/Volume dial
NOTE
To prevent the battery from being
discharged, do not leave the audio
system on for a long period when the
engine is not running.
shuseizumi_J56J_8R29_EA_02I.book Page 24 Saturday, September 7, 2002 12:58 PM

6-31
Interior Comfort
Au d i o S y s t e m
Form No. 8R29-EA-02I
Fast-forward/Rewind
Press the fast-forward button ( ) to
fast-forward.
Press the rewind button ( ) to rewind.
To stop this operation and play the
cassette tape, press the button again.
Reversing
Press the program button ( ) to
change cassette tape-playing direction.
Automatic program control (APC)
APC is used to find the beginning of
either the next program or the one being
played.
Press the APC button ( ) to the
beginning of the next selection.
Press the APC button ( ) to the
beginning of the one being played. To
stop this operation and play the cassette
tape, press the button again.Repeat play
This operation makes it possible to listen
to a selection repeatedly.
Press the repeat button ( ) during play.
The current selection playing will be
repeated ("RPT" will be displayed).
Press the repeat button ( ) once again
to cancel repeat play.
NOTE
The cassette tape can be ejected when
the ignition switch is in the OFF
position.
NOTE
When the cassette tape ends during
fast forward or rewind, it automatically
stops and starts playing.
NOTE
When the cassette tape ends, the unit
automatically reverses play.
NOTE
APC may not operate properly if
•
A tape was recorded at a low level.
•
A tape has long, silent intervals.
•
A tape is a live recording.
•
A tape has very short intervals of
less than 3 seconds.
NOTE
RPT may not operate properly if
•
A tape was recorded at a low level.
•
A tape has long, silent intervals.
•
A tape is a live recording.
•
A tape has very short intervals of
less than 3 seconds.
shuseizumi_J56J_8R29_EA_02I.book Page 31 Saturday, September 7, 2002 12:58 PM

6-37
Interior Comfort
Au d i o S y s t e m
Form No. 8R29-EA-02I
Multiple insertion
1. Press and hold the load button ( )
for about 2 seconds until a beep is
heard.
2. When "In" is displayed, insert the CD.
3. When "In" is displayed again, insert
the next CD.
Ejecting the CD
Normal ejection
1. Press the CD eject button ( ). The disc
number and "DISC OUT" will be
displayed.
2. Pull out the CD.
Ejecting CDs from desired tray number
1. Press and hold the CD eject button ( )
for about 2 seconds until a beep is
heard.
2. Press the channel preset button for the
desired CD number within 5 seconds
after the beep is heard.
3. Pull out the CD.Multiple ejection
1. Press and hold the CD eject button ( )
for about 2 seconds until a beep is
heard.
2. Wait 5 seconds or press the CD eject
button ( ) again within 5 seconds after
the beep is heard.
3. Pull out the CD, then the next CD will
be ejected.
NOTE
The first-inserted CD will be played
automatically when:
•
No CD is inserted within 15
seconds after "In" is displayed.
•
The CD trays are full.
NOTE
When the CD is ejected during play,
the next CD will be played
automatically.
NOTE
•
CDs will be ejected starting with the
one with the lowest number.
•
All CDs in the tray will be ejected
continuously.
•
CDs can be ejected when the
ignition switch is off. Press and hold
the CD eject button ( ) for about 2
seconds and all CDs will eject.
shuseizumi_J56J_8R29_EA_02I.book Page 37 Saturday, September 7, 2002 12:58 PM

6-43
Interior Comfort
Form No. 8R29-EA-02I
Interior Equipment
When you need a sunvisor, lower it for use
in front or swing it to the side.

Vanity Mirrors
To use the vanity mirror, lower the
sunvisor.
If your vehicle is equipped with a vanity
mirror light, it will illuminate when you
pull the cover up.

Illuminated Entry System
When the switch is in the DOOR position,
the overhead light and the courtesy lights
come on for:
•
About 30 seconds after the driver’s
door is unlocked and the ignition key is
removed.
•
About 15 seconds after all doors are
closed.
•
About 15 seconds after the key is
removed from the ignition with all
doors closed.
The light also goes out when:
•
The ignition switch is turned to the ON
position and all doors are closed.
•
The driver’s door is locked.
Sunvisors
Sunvisor
Interior Lights
NOTE
If any door is left opened, the light
goes out after about 5 minutes.
The light turns on again when the
ignition switch is turned to the ON
position, or when any door is opened
after all doors have been closed.
shuseizumi_J56J_8R29_EA_02I.book Page 43 Saturday, September 7, 2002 12:58 PM

6-47
Interior Comfort
Interior Equipment
Form No. 8R29-EA-02I

Clock
When the ignition switch is in the ACC or
ON position, the time is displayed.
Time setting
1. Press the CLOCK button until a beep
sounds, and "12Hr" and "24Hr" will be
displayed.
2. Press the SET button to switch between
"12Hr" and "24Hr" displays. The
selected display will flash.
To select the desired clock setting,
press the CLOCK button again while
the preferred setting is flashing.
3. "Hr. ADJUST" will be displayed next,
and the hour portion of the display will
flash. Press the SET button to set the
hour, then press the CLOCK button.
4. "Min. ADJUST" will be displayed
next, and the minutes portion of the
display will flash. Press the SET button
to set the minutes, then press the
CLOCK button.Time resetting
While the clock is displayed, press the
SET button 1.5 seconds or more. When
the button is released, a beep will sound
and the clock will be reset as follows:
(Example)
12:01—12:29→
12:00
12:30—12:59→
1:00
NOTE
When the SET button is released, the
seconds are reset to "00".
shuseizumi_J56J_8R29_EA_02I.book Page 47 Saturday, September 7, 2002 12:58 PM

6-48
Interior Comfort
Interior Equipment
Form No. 8R29-EA-02I

Ambient Temperature Display
When the ignition switch is in the ON
position, press the AMB button to display
the ambient temperature.

Climate Control Display
Climate control is displayed when the
climate control system is turned on (page
6-5).

Audio Display
Audio is displayed when the audio system
is turned on (page 6-23).

Display Dimmer Cancel Function
When driving at night on snowy or foggy
roads, or in other situations when the
display’s visibility is reduced due to glare
from surrounding brightness, the display
dimmer cancel function increases the
intensity of the display illumination.
The display dimmer cancel function can
be used when the headlight switch is in
the or position.
Press the DIMMER button to increase the
intensity of the display illumination.
Press the button again to return to the
previous display illumination.
NOTE
•
The displayed ambient temperature
may vary from the actual ambient
temperature depending on the
surrounding area and vehicle
conditions.
•
Press the AMB button again to
switch the display from ambient
temperature to the temperature set
for the air conditioner.
•
Press the AMB button 1.5 seconds
or more to switch the display from
Fahrenheit to Centigrade or vice
versa.
shuseizumi_J56J_8R29_EA_02I.book Page 48 Saturday, September 7, 2002 12:58 PM

6-49
Interior Comfort
Interior Equipment
Form No. 8R29-EA-02I
The ignition switch must be in the ACC or
ON position.
1. Open the cover.
2. Press the lighter in and release it. When
ready for use, it automatically pops out.
Lighter
•
Don’t touch the metal part of the
lighter, you may burn yourself.
•
Don’t hold the lighter in because it
will overheat.
•
Don’t use the lighter socket for
plug-in accessories such as shavers
and coffee pots. They may damage
it or cause electrical failure. Use
only a genuine Mazda lighter or the
equivalent.
•
If the lighter doesn’t pop out within
30 seconds, remove it to prevent
overheating.
CAUTION
shuseizumi_J56J_8R29_EA_02I.book Page 49 Saturday, September 7, 2002 12:58 PM

6-54
Interior Comfort
Interior Equipment
Form No. 8R29-EA-02I
The ignition switch must be in the ACC or
ON position.
Only use genuine Mazda accessories or
the equivalent requiring no greater than
120 W (DC12 V, 10 A).When placing an electrical device (e.g.
cellular phone) in the tray which is
connected with the accessory socket, pass
the plug cord through the slot in the cap.
1. Open the lid by pulling the upper
release catch.
2. Remove the tray mat.
3. Using a coin, turn the cap
counterclockwise (about 45°
from the
closed position) and remove it.
4. Open the tray by pulling the lower
release catch.
Accessory Socket
To prevent accessory socket damage or
electrical failure, pay attention to the
following;
•
Don’t use accessories that require
more than 120 W (DC12 V, 10 A).
•
Don’t use accessories that are not
genuine Mazda accessories or the
equivalent.
•
Close the cover when the accessory
socket is not in use.
•
Correctly insert the plug into the
accessory socket.
NOTE
To prevent discharging the battery,
don’t use the socket for long periods
with the engine off or idling.
CAUTION
Cap slot, closed
Cap slot, opened
shuseizumi_J56J_8R29_EA_02I.book Page 54 Saturday, September 7, 2002 12:58 PM