2004 Lexus IS300 buttons

KEYS AND DOORS
21
NOTE: *The 2-step unlocking function can be changed.**The interior light can be set not to come on or the durationof lighting can be changed. Ask your Lexus dealer for details.
Locking with inside lock button
SV11004

1Lock 2Unlock
Push in the lock button to lock and unlock the door.
The front doors can be opened by pulling the inside handles
even if the lock buttons are in the locked position.
CAUTION
Do not pull the inside handle of the front doors while
driving. The doors will open and an accident may occur.
Lexus strongly recommends that all children be placed
in the rear seat of the vehicle.
Closing the door with the lock button pushed in will also lock
the door. Be careful not to lock your keys in the vehicle. The
door will not lock if the key is left in the ignition switch when
closing the front doors.
CAUTION
Before driving, make sure the doors are closed and
locked, especially when small children are in the
vehicle. Along with the proper use of seat belts, locking
the doors helps prevent the driver and passengers from
being thrown out from the vehicle during an accident.
It also helps prevent the doors from being opened
unintentionally.
03 07.09

INTERIOR EQUIPMENT
67
GARAGE DOOR OPENER
The garage door opener (HomeLink Universal
Transceiver) is manufactured under license from
HomeLink
 and can be programmed to operate garage
doors, gates, entry doors, door locks, home lighting
systems, and security systems, etc.
(a) Programming the HomeLink
SV14007

1Buttons 2Indicator light
The HomeLink in your vehicle has 3 buttons and you can
store one program for each button.
To ensure correct programming into the HomeLink
, install a
new battery in the hand- held transmitter prior to
programming. The battery side of the hand- held transmitter must be pointed
away from the HomeLink
 during the programming process.
For Canadian users, follow the procedure in ºProgramming an
entrance gate/Programming all devices in the Canadian
marketº.
1. Decide which of 3 HomeLink
 buttons you want to
program.
2. Place your hand- held garage transmitter 25 to 75 mm (1
to 3 in.) away from the surface of the HomeLink
.
Keep the indicator light on the HomeLink
 in view while
programming.
3. Simultaneously press and hold the hand- held garage
transmitter button along with the selected HomeLink
 button.
4. When the indicator light on the HomeLink
 changes from
a slow to a rapid flash after 20 seconds, you can release both
buttons.
5. Test the operation of the HomeLink
 by pressing the newly
programmed button. If programming a garage door opener,
check to see if the garage door opens and closes.
If the garage door does not operate, identify if your garage
transmitter is of the ºRolling Codeº type. Press and hold the
programmed HomeLink
 button. The garage door has the
rolling code feature if the indicator light (on the HomeLink)
flashes rapidly and then remains lit after 2 seconds. If your
garage transmitter is the ºRolling Codeº type, proceed to the
heading ºProgramming a rolling code systemº.
6. Repeat steps 2 through 5 for each remaining HomeLink

button to program another device.
03 07.09

INTERIOR EQUIPMENT
68
Programming a rolling code system
If your device is ºRolling Codeº equipped, it is necessary
to follow steps 1 through 4 under the heading
ºProgramming the HomeLink
º before proceeding with
the steps listed below.
1. Locate the ºtrainingº button on the ceiling mounted garage
door opener motor. The exact location and color of the button
may vary by brand of garage door opener. Refer to the owner's
guide supplied by the garage door opener manufacturer for the
location of this ºtrainingº button.
2. Press the ºtrainingº button on the ceiling mounted garage
door opener motor.
Following this step, you have 30 seconds in which to initiate
step 3 below.
3. Press and release the vehicle's programmed HomeLink

button twice. The garage door may open. If the door does
open, the programming process in complete. If the door does
not open, press and release the button a third time. This third
press and release will complete the programming process by
opening the garage door.
The ceiling mounted garage door opener motor should now
recognize the HomeLink
 unit and be able to activate the
garage door up/down.
4. Repeat steps 1 through 3 for each remaining HomeLink

button to program another rolling code system.
Programming an entrance gate /
Programming all devices in the Canadian
market
1. Decide which of the 3 HomeLink buttons you want to
program.
2. Place your hand- held gate/device transmitter 25 to 75 mm
(1 to 3 in.) away from the surface of the HomeLink
.
Keep the indicator light on the HomeLink
 in view while
programming.
3. Press and hold the selected HomeLink
 button.
4. Continuously press and release (cycle) the hand- held
gate/device transmitter button every two seconds until step 5
is complete.
5. When the indicator light on the HomeLink
 changes from
a slow to a rapid flash after 20 seconds, you can release both
buttons.
6. Test the operation of the HomeLink
 by pressing the newly
programmed button. Check to see if the gate/device operates
correctly.
7. Repeat steps 1 through 6 for each remaining HomeLink

button to program another device.
Programming other devices
To program other devices such as home security systems,
home door locks or lighting, contact your authorized Lexus
dealer for assistance.
03 07.09

INTERIOR EQUIPMENT
69
Reprogramming a button
Individual HomeLink buttons cannot be erased, however, to
reprogram a single button, follow the procedure Programming
the HomeLink
º.
(b) Operating the HomeLink
To operate the HomeLink, press the appropriate HomeLink
button to activate the programmed device. The HomeLink
indicator light should come on. The HomeLink continues to
send the signal for up to 20 seconds as long as the button is
pressed.
(c) Erasing the entire HomeLink memory
(all three programs)
To erase all previously programmed codes at one time, press
and hold down the 2 outside buttons for 20 seconds until the
indicator light flashes.
If you sell your vehicle, be sure to erase the programs stored
in the HomeLink
 memory.
CAUTION
 When programming the HomeLink Universal
Transceiver, you may be operating a garage door or
other device. Make sure people and objects are out
of the way of the garage door or other device to
prevent potential harm or damage.
 Do not use this HomeLink
 Universal Transceiver
with any garage door opener that lacks the safety
stop and reverse feature as required by federal safety
standards. (This includes any garage door opener
model manufactured before April 1, 1982.) A garage
door opener which cannot detect an object (signaling
the door to stop and reverse), does not meet current
federal safety standards. Using a garage door
opener without these features increases risk of
serious injury or death.
03 07.09

OCCUPANT RESTRAINT SYSTEMS
11 9
Be sure to wear the seat belt without the seat belt
extender if you can fasten the seat belt without the
extender.
 Do not use the seat belt extender when installing a
child restraint system on the front or rear passenger
seat. If installing a child restraint system with the seat
belt extender connected to the seat belt, the seat belt
will not securely hold the child restraint system,
which could cause death or serious injury to the child
or other passengers in the event of collision.
SV16050
To connect the extender to the seat belt, insert the tab into
the seat belt buckle so that the ºPRESSº signs on the
buckle release buttons of the extender and the seat belt
are both facing outward as shown.
You will hear a click when the tab locks into the buckle.
When releasing the seat belt, press on the buckle release
button on the extender, not on the seat belt. This helps prevent
damage to the vehicle interior and extender itself.
When not in use, remove the extender and store in the vehicle
for future use.
03 07.09

AUDIO
205
1Turning the system on and adjusting the volume
(See page 208 for details.)
2Compact disc slot
(See page 219 for details.)
3Ejecting a compact disc
(See page 220 for details.)
4Traffic announcement/Program type
(See page 214 for details.)
5Compact disc pre-load button
(See page 219 for details.)
6Audio control knob/Frequency tuning
(See page 209 for details.)
7Mode selectors
(See page 208 for details.)
8Message
(See page 215 for details.)
9Function buttons
1 - 6: Station selector buttons
(See page 212 for details.)
:Disc selection
(See page 222 for details.)
RPT: Automatic repeat
(See page 217 or 224 for details.) RAND:
Random access
(See page 224 for details.)
SKIP: Automatic skip of blank portions of tape
(See page 217 for details.)
 :Rewinding or reversing
(See page 217 or 224 for details.)


:Fast forwarding
(See page 217 or 224 for details.)
:


: Side change
(See page 217 for details.)
DOLBY NR button
(See page 216 for details.)
10Cassette tape slot
(See page 216 for details.)
11Ejecting a cassette tape
(See page 216 for details.)
12Radio mode: Frequency tuning
(See page 212 for details.)
TAPE mode: Direct access to a desired program
(See page 218 for details.)
CD mode: Direct access to a desired program
(See page 224 for details.)
13Scan tuning button
(See page 213 for details.)
03 07.09

AUDIO
207
1Turning the system on and adjusting the volume
(See page 208 for details.)
2Compact disc slot
(See page 221 for details.)
3Ejecting a compact disc
(See page 221 for details.)
4Audio control knob/Frequency tuning
(See page 209 for details.)
5Mode selectors
(See page 208 for details.)
6Cassette tape slot
(See page 216 for details.)
7Function buttons
1 - 6: Station selector buttons
(See page 212 for details.)
:Disc selection
(See page 222 for details.)
RPT: Automatic repeat
(See page 217 or 224 for details.)
RAND: Random access
(See page 224 for details.)
SKIP: Automatic skip of blank portions of tape
(See page 217 for details.) 
:Rewinding or reversing
(See page 217 or 224 for details.)


:Fast forwarding
(See page 217 or 224 for details.)
:


: Side change
(See page 217 for details.)
DOLBY NR button
(See page 216 for details.)
8Ejecting a cassette tape
(See page 216 for details.)
9Radio mode: Frequency tuning
(See page 212 for details.)
TAPE mode: Direct access to a desired program
(See page 218 for details.)
CD mode: Direct access to a desired program
(See page 224 for details.)
10Scan tuning button
(See page 213 for details.)
03 07.09

AUDIO
208
Using your audio system: some basics
This section describes some of the basic features of the Lexus
audio system. Some information may not pertain to your
system.
Your audio system works when the ignition key is in the ºACCº
or ºONº position.
NOTICE
To prevent the battery from being discharged, do not leave the car audio on longer than necessary when theengine is not running.
(a) Turning the system on and off
SV22067
Push this knob to turn the audio system on and off. Turn
this knob to adjust the volume.
The system turns on in the last mode used.
SV22068
Push ºAMº, ºFMº, ºT APEº or ºDISCº to turn on that mode.
The selected mode turns on directly.
Push these buttons if you want to switch from one mode to
another.
If the tape or disc is not set, the cassette player or compact disc
player does not turn on.
You can turn off the cassette player by ejecting the cassette
tape. If the audio system was previously off, then the entire
audio system will be turned off when you eject the cassette
tape. If another function was previously playing, it will come on
again.
03 07.09