2004 ISUZU TF SERIES battery location

ENGINE DRIVEABILITY AND EMISSIONS 6E–275
IGNITION COIL
Location
Back of the engine right-hand side.
Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the ignition coil connector.
3. Disconnect four spark plug cables from the ignition
coil.
4. Loosen three bolts and remove ignition coil from the
bracket.
Installation Procedure
1. Tighten the ignition coil by three bolts.
2. Connect four spark plug cables to the ignition coil.
3. Connect a ignition coil connector to the ignition coil.
4. Connect the negative battery cable.
NOTE: Verify any DTCs (diagnosis Trouble Code) are
not stored after replacement.
Verify proper connection of spark plug cables for each
cylinders.
SPARK PLUGS
Location
Installed on the left-hand side of cylinder head.
Removal Procedure
1. Disconnect the negative battery cable
2. Remove the spark plug cable.
3. Remove the spark plug.
Inspection
1. Check the insulator for cracks. Replace the spark
plug if cracks are present.
2. Check the electrode condition and replace the spark
plug if necessary.
If the spark plug electrodes and insulators are fouled
with carbon or oil, the engine will not operate efficiently.
There are a number of possible causes:
Fuel mix ture is too rich.

IMMOBILIZER SYSTEM 11A-31

Diagnostic procedure


Once the cause of DTC is repaired or gone,
engine can be operated normally, and present
DTC becomes history code.


History code is canceled by no repeat failure on 25
consequence ignition key on afterward.


History code cannot be canceled by batter
y
connector disconnected.
Clearing Diagnostic Trouble Codes
IMPORTANT:
Do not clear DTCs unless directed to do
so by the service information provided for each
diagnostic procedure. When DTCs are cleared, the
Failure Record data which may help diagnose an
intermittent fault will also be erased from memory.
Verifying Vehicle Repair
Verification of vehicle repair will be more
comprehensive for vehicles with immobilizer system
diagnostic. Following a repair, the technician should
perform the following steps:
1.
Review and record the Fail Records for the DTC
which has been diagnosed.
2.
Clear DTC(s).
3.
Operate the vehicle within conditions noted in the
Fail Records.
4.
Monitor the DTC status information for the DTC
which has been diagnosed until the diagnostic test
associated with that DTC runs.
Following these steps are very important in verifying
repairs on immobilizer systems. Failure to follow these
steps could result in unnecessary repairs.
Diagnostic Aids
Check the condition for system parts.



Installation condition, poor connection, damage,
system parts malfunction. Harness, Fuse, Relay,
Immobilizer coil (antenna), Key, Meter, Immobilize
r
control unit (ICU), Engine control module (ECM).
NOE: Breakage of immobilizer fuse does not operate
immobilizer system. Check engine lamp flashes at this
time.

Check the Electro-Magnetic Interference (EMI)



Location of vehicle check

Move the vehicle to a new location and perform
the check again.


Non-OEM Parts.

Switch is "OFF" or remove the Non-OEM parts and
perform the check again.


Other

Remove the accessory and another key from key.

Check the other items.



Battery voltage is low.


Immobilizer programming functions.

Must be programmed immobilizer system.


Registration for security code, immobilizer control
unit parts number.


Key switch operation.

Immobilizer system may detect a history DTC b
y
the timing of ON-OFF of a key switch.


Active the immobilizer system.


Keyless entry system is malfunction.


Anti theft system is malfunction.

Check the operation

Check the operation "Lock / unlock" by using transmitte
r
(key) on the vehicle.

ANTITHEFT SYSTEM 11B – 3
Service Precaution
WARNING:
THIS VEHICLE HAS A SUPPLEMENTAL RESTRAINT SYSTEM (SRS). REFER TO THE SRS COMPONENT AND
WIRING LOCATION VIEW IN ORDER TO DETERMINE WHETHER YOU ARE PERFORMING SERVICE ON OR
NEAR THE SRS COMPONENTS OR THE SRS WIRING. WHEN YOU ARE PERFORMING SERVICE ON OR
NEAR THE SRS COMPONENTS OR THE SRS WIRING, REFER TO THE SRS SERVICE INFORMATION.
FAILURE TO FOLLOW WARNINGS COULD RESULT IN POSSIBLE AIR BAG DEPLOYMENT, PERSONAL
INJURY, OR OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
CAUTION:
Always use the correct fastener in the proper location. When you replace a fastener, use ONLY the exact
part number for that application. ISUZU will call out those fasteners that require a replacement after
removal. ISUZU will also call out the fasteners that require thread lockers or thread sealant. UNLESS
OTHERWISE SPECIFIED, do not use supplemental coatings (Paints, greases, or other corrosion inhibitors)
on threaded fasteners or fastener joint interfaces. Generally, such coatings adversely affect the fastener
torque and the joint clamping force, and may damage the fastener. When you install fasteners, use the
correct tightening sequence and specifications. Following these instructions can help you avoid damage
to parts and systems.
DTC20 Broken wire to door lock actuators ............................................................ 11B – 42
DTC21 Remote key 1 with random code out of capture range ............................ 11B – 43
DTC22 Remote key 2 with random code out of capture range ............................ 11B – 44
DTC23 Remote key 3 with random code out of capture range ............................ 11B – 45
DTC24 Remote key 4 with random code out of capture range ............................ 11B – 46
DTC25 Remote key 5 with random code out of capture range ............................ 11B – 47
DTC28 Input immobiliser short circuit to ground .................................................. 11B – 48
DTC29 Broken wire to immobiliser ......................................................................... 11B – 49
DTC31 Actuator driver door defect ......................................................................... 11B – 50
DTC32 Actuator passenger door defect .................................................................. 11B – 51
DTC36 Broken wire to driver door........................................................................... 11B – 52
DTC37 Broken wire to passenger door ................................................................... 11B – 53
DTC41 Driver door micro switch unlock defect ..................................................... 11B – 54
DTC42 Driver door micro switch lock defect .......................................................... 11B – 55
DTC43 Driver door micro switch dead lock defect ................................................ 11B – 56
DTC44 Passenger door micro switch lock defect................................................... 11B – 57
DTC45 Passenger door micro switch unlock defect .............................................. 11B – 58
DTC47 Battery voltage for door lock actuators is missing ................................... 11B – 59
DTC50 A/D converter defect or battery voltage less than 9 volt ......................... 11B – 60
DTC51 E E P ROM defect .......................................................................................... 11B – 61
DTC52 E E P ROM not programmed by ISUZU ...................................................... 11B – 62
DTC55 Control unit defect ........................................................................................ 11B – 63
DTC123 Output flasher short circuit to grpund or broken wire ........................... 11B – 64
DTC125 Output alarm horn broken wire ................................................................ 11B – 65

POWER-ASSISTED STEERING SYSTEM 3B-31

Supplemental Restraint System Steering Wheel & Column
Service Precaution
This steering wheel and column repair section covers
the Supplemental Restraint System (SRS) steering
column. The following repair procedures are specific to
SRS components. When servicing a vehicle equipped
with Supplemental Restraint System, pay close attention
to all WARNINGS and CAUTIONS.
For detailed explanation about SRS, refer to Restraints
section.
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE
SRS COMPONENTS OR THE SRS WIRING, REFE
R
TO THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN POSSIBLE
AIR BAG DEPLOYMENT, PERSONAL INJURY, O
R
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
SAFE HANDLING OF INFLATOR MODULES
REQUIRES FOLLOWING THE PROCEDURES
DESCRIBED BELOW FOR BOTH LIVE AND
DEPLOYED MODULES.
SAFETY PRECAUTIONS MUST BE FOLLOWED
WHEN HANDLING A DEPLOYED AIR BAG
ASSEMBLY (AIR BAG). AFTER DEPLOYMENT, THE
AIR BAG ASSEMBLY (AIR BAG) SURFACE MAY
CONTAIN A SMALL AMOUNT OF SODIUM
HYDROXIDE, A BY-PRODUCT OF THE
DEPLOYMENT REACTION, THAT IS IRRITATING TO
THE SKIN AND EYES. MOST OF THE POWDER ON
THE AIR BAG ASSEMBLY (AIR BAG) IS HARMLESS.
AS A PRECAUTION, WEAR GLOVES AND SAFETY
GLASSES WHEN HANDLING A DEPLOYED AIR BAG
ASSEMBLY, AND WASH YOUR HANDS WITH MILD
SOAP AND WATER AFTERWARDS.

WHEN CARRYING A LIVE AIR BAG ASSEMBLY,
MAKE SURE THE BAG AND TRIM COVER ARE
POINTED AWAY FROM YOU. NEVER CARRY AN AI
R
BAG ASSEMBLY BY THE WIRES OR CONNECTO
R
ON THE UNDERSIDE OF MODULE. IN THE CASE OF
AN ACCIDENTAL DEPLOYMENT, THE BAG WILL
THEN DEPLOY WITH MINIMAL CHANCE OF INJURY.
WHEN PLACING A LIVE AIR BAG ASSEMBLY ON A
BENCH OR OTHER SURFACE, ALWAYS FACE THE
BAG AND TRIM COVER UP, AWAY FROM THE
SURFACE.
NEVER REST A STEERING COLUMN ASSEMBLY
ON THE STEERING WHEEL WITH THE AIR BAG
ASSEMBLY FACE DOWN AND COLUMN VERTICAL.
THIS IS NECESSARY SO THAT A FREE SPACE IS
PROVIDED TO ALLOW THE AIR BAG ASSEMBLY
TO EXPAND IN THE UNLIKELY EVENT OF
ACCIDENTAL DEPLOYMENT. OTHERWISE,
PERSONAL INJURY COULD RESULT.
TO AVOID DEPLOYMENT WHEN
TROUBLESHOOTING THE SRS SYSTEM, DO NOT
USE ELECTRICAL TEST EQUIPMENT, SUCH AS
BATTERY-POWERED OR A/C-POWERED VOLT-
METER, OHMMETER, ETC., OR ANY TYPE OF
ELECTRICAL EQUIPMENT OTHER THAN SPECIFIED
IN THIS MANUAL. DO NOT USE A NON-POWERED
PROBE-TYPE TESTER.
INSTRUCTIONS IN THIS MANUAL MUST BE
FOLLOWED CAREFULLY, OTHERWISE PERSONAL
INJURY MAY RESULT.

SRS Connectors
CAUTION: The special yellow color connectors are
used for supplemental restraint system-air bag
circuit.
When removing the cable harness, do not pull the
cables. Otherwise, cable disconnection may occur.
When connect the SRS connector, insert the
connector completely. Imperfect locking may cause
malfunction of SRS circuit.

7A1-6 CONSTRUCTION AND FUNCTION
ELECTRONIC CONTROL COMPONENTS LOCATION

4WD Only 4WD Only
Instrument panel (Meter)







Speed meter (2WD Only)
Shift position indicator lamp
POWER DRIVE, 3rd START
indicator lamp
A/T OIL TEMP indicator lamp
CHECK TRANS indicator lam
p

Brake pedal





Brake Switch
Select lever








Power Drive
, 3rd Start select switch
Transmission Control Module (TCM)
Electrical source






Ignition
Battery voltage
Speed sensor
Turbine sensor
Inhibitor switch
ATF thermo sensor
High clutch oil pressure switch
2-4 brake oil pressure switch
Low & Reverse brake oil pressure
switch
Line pressure solenoid
Low clutch solenoid
High clutch solenoid
2-4 brake solenoid
Low & Reverse brake solenoid
Lock-up solenoid
Transmission
Transfer Control Module
Transfer




4L mode switch
Engine




Engine speed sensor
Throttle Position Sensor


Engine Control Module (ECM)
Data link connector

DIAGNOSIS (JR405E) 7A2-43
DTC P0560 (Flash Code 16) System Voltage Failure
TCM


A1 (+B)



B5

B15

H23 (15)C95 (5)
(15)
BLK/YEL
BLK
BLK
Battery
C94
(1)
BLK


Setting Condition:

The supply voltage is below 10V and the engine speed exceeds 1000 rpm for more than 1 second.

Fail Safe:

When the vehicle is running, the gear position selected at the trouble detection is held and the lock-up is
inhibited.

After the vehicle stopped, all solenoid operations stop (OFF) and the gear is fixed to the 3rd. (In case of fail-safe
valve failure, gear shift to 4th (over-drive) is inhibited.)

Possible Cause:

Alternator or battery malfunction.

Power supply wire open circuit or short circuit to ground between power supply and TCM terminal A1 (C94).

Ground wire open circuit or short circuit to battery between ground location and TCM terminal B5 (C95) or B15
(C95).

Poor connection of each connector.