2004 ISUZU TF SERIES ignition

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-45
Signal or Continuity Tester Position Pin
No.

B/Box
No.
Pin Function Wire
Color
Key SW
Off Key SW
On Engine
Idle Engine
2000rpmECM
Connection Range(+) (-)
A31 A31 No. 3 Ignition
Coil RED/
BLU - - Wave form - - - -
A32 A32 No. 1 Ignition
Coil RED - - Wave form - - - -
A33 A33 Ground (Power) BLK/
RED Continuity
with ground - - - Disconnect Ohm A33 GND
A34 A34 No. 5 Injector GRN/
BLK Less than 1V Wave form or 12-14V Connect DC V A34 GND
A35 A35 No. 3 Injector BLU Less than 1V Wave form or 12-14V Connect DC V A35 GND
A36 A36 No. 1 Injector GRN/
WHT Less than 1V Wave form or 12-14V Connect DC V A36 GND
A37 A37 Ground (Case) BLK/
RED Continuity
with ground - - - Disconnect Ohm A37 GND
A38 A38 No Connection - - - - - - - - -
A39 A39 No Connection - - - - - - - - -
A40 A40 No Connection - - - - - - - - -

6E-46 3.5L ENGINE DRIVEABILITY AND EMISSIONS

Connector B Port: View Looking Into ECM Cace





Signal or Continuity Tester Position Pin
No. B/Box
No. Pin Function Wire
Color
Key SW Off Key SW On Engine IdleEngine
2000rpm ECM
Connection Range (+) (-)
B1 B1 No Connection - - - - - - - - -
B2 B2 No Connection - - - - - - - - -
B3 B3 No. 2 Injector GRN/
ORG Less than 1V Wave form or 12-14V Connect DC V B3 GND
B4 B4 No. 4 Injector GRN/
RED Less than 1V Wave form or 12-14V Connect DC V B4 GND
B5 B5 No. 6 Injector GRN/
YELLess than 1V Wave form or 12-14V Connect DC V B5 GND
B6 B6 Ground
(Power) BLK Continuity
with ground - - - Disconnect Ohm B6 GND
B7 B7 No. 2 Ignition
Coil RED/
BLK- - Wave form - - - -
B8 B8 No. 4 Ignition
Coil RED/
WHT - - Wave form - - - -
B9 B9 No. 6 Ignition
Coil RED/
GRN - - Wave form - - - -
B10 B10 No Connection - - - - - - - - -
B11 B11 A/C
Compressor
Relay GRY/
RED Less than 1V A/C comp. is operated: Less than 1V
A/C comp. is not operated: 10-14V Connect DC V B11 GND
B12 B12 Tachometer
Output Signal BLK/
RED - - Wave form or
6.2V Wave form or
6.2V Connect AC V B12 GND
B13 B13 Idle Air Control
(IAC) Valve
Coil A High BLU Less than 1V Less than 1V / 10-14V Connect DC V B13 GND
B14 B14 Idle Air Control
(IAC) Valve
Coil B High BLU/
WHT Less than 1V Less than 1V / 10-14V Connect DC V B14 GND
B15 B15 Canister Purge
Solenoid Valve RED/
BLULess than 1V Wave form or 12-14V Connect AC V B15 GND

6E-48 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Signal or Continuity Tester Position Pin
No. B/Box
No. Pin Function Wire
Color
Key SW Off Key SW On Engine IdleEngine
2000rpm ECM
Connection Range (+) (-)
B32 B32 Vehicle Speed
Signal
(Immobilizer
Control Unit
Terminal B8) WHT - - Wave form or approx. 6.5V at
20km/h Connect AC V B32 GND
B33 B33 Ignition Switch BLU/
YELLess than 1V 10-14V Connect DC V B33 GND
B34 B34 Back Up
Power Supply RED/
WHT 10-14V Connect DC V B34 GND
B35 B35 No Connection - - - - - - - - -
B36 B36 ECM Main
Relay RED/
BLUWhile main
relay is
activated:
10-14V
Main relay is
not activated:
Less than 1V 10-14V Connect DC V B36 GND
B37 B37 ECM Main
Relay RED/
BLUWhile main
relay is
activated:
10-14V
Main relay is
not activated:
Less than 1V 10-14V Connect DC V B37 GND
B38 B38 To Data Link
Connect to No.
2 GRN - - - - - - - -
B39 B39 TPS, MAF, IAT
& CMP Sensor
Ground RED Continuity
with ground - - - Connect Ohm B39 GND
B40 B40 No Connection - - - - - - - - -

6E-50 3.5L ENGINE DRIVEABILITY AND EMISSIONS

Injector Control Signal Reference Wave Form











0V






Measurement Terminal: A36(+) (No.1 Cylinder) GND(-)
Measurement Scale: 20V/div 10ms/div
Measurement Condition: Approximately 2000rpm
Ignition Coil Control Signal Reference Wave Form









0V








Measurement Terminal: A32(+) (No.1 Cylinder) GND(-)
Measurement Scale: 5V/div 10ms/div
Measurement Condition: Approximately 2000rpm
Injector & Ignition Coil Control Signal Reference Wave Form










CH1
0V


CH2
0V


Measurement Terminal: CH1: A36(+) (No.1 Cylinder)
CH2: A32(+) (No.1 Cylinder) GND(-)
Measurement Scale: CH1: 20V/div / CH2: 5V/div 10ms/div
Measurement Condition: Approximately 2000rpm
EVAP Canistor Purge Solenoid Reference Wave Form









0V








Measurement Terminal: B15(+) GND(-)
Measurement Scale: 10V/div 20ms/div
Frequency: Approximately 16Hz
EGR Solenoid Reference Wave Form









0V








Measurement Terminal: CH1: A5(+) GND(-)
Measurement Scale: CH1: 10V/div 2ms/div
Frequency: Approximately 128Hz

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-51

GENERAL DESCRIPTION FOR ECM AND
SENSORS
Engine Control Module (ECM)


1 2
(1) A Port
(2) B Port


The engine control module (ECM) is located on the
common chamber. The ECM controls the following.

Fuel metering system

Ignition timing

On-board diagnostics for powertrain functions.

The ECM constantly observes the information from
various sensors. The ECM controls the systems tha
t
affect vehicle performance. And it performs the
diagnostic function of the system.
The function can recognize operational problems, and
warn to the driver through the check engine lamp, and
store diagnostic trouble code (DTC). DTCs identify the
problem areas to aid the technician in marking repairs.

The input / output devices in the ECM include analog to
digital converts, signal buffers, counters and drivers.
The ECM controls most components with electronic
switches which complete a ground circuit when turned
on.

Inputs (Operating condition read):

Battery voltage

Electrical ignition

Exhaust oxygen content

Mass air flow

Intake air temperature

Engine coolant temperature

Crankshaft position

Camshaft position

Throttle position

Vehicle speed

Power steering pressure

Air conditioning request on or off

EGR valve position

Outputs (Systems controlled):

Ignition control

Fuel control

Idle air control

Fuel pump

EVAP canister purge

Air conditioning

Diagnostics functions

The vehicle with automatic transmission, the
interchange of data between the engine control module
(ECM) and the transmission control module (TCM) is
performed via a CAN-bus system.
The following signals are exchanged via the CAN-bus:

ECM to TCM:

ECM CAN signal status

Engine torque

Coolant temperature

Throttle position

Engine speed

A/C status

CAN valid counter

TCM to ECM:

Ignition timing retard request

Garage shift status

CAN valid counter

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-53
Idle Air Control (IAC) Valve








Step
CoilAB CD
Coil A High
(EC M B13)On On
Coil A Low
(EC M B16)On On
Coil B High
(EC M B14)On On
Coil B Low
(EC M B17)On On

(IAC Valve Close Direction)
(IAC Valve Open Direction)



The idle air control valve (IAC) valve is two directional
and gives 2-way control. It has a stepping moto
r
capable of 256 steps, and also has 2 coils. With power
supply to the coils controlled steps by the engine control
module (ECM), the IAC valve's pintle is moved to adjus
t
idle speed, raising it for fast idle when cold or there is
extra load from the air conditioning or power steering.
By moving the pintle in (to decrease air flow) or out (to
increase air flow), a controlled amount of the air can
move around the throttle plate. If the engine speed is
too low, the engine control module (ECM) will retract the
IAC pintle, resulting in more air moving past the throttle
plate to increase the engine speed.
If the engine speed is too high, the engine control
module (ECM) will extend the IAC pintle, allowing less
air to move past the throttle plate, decreasing the
engine speed.

The IAC pintle valve moves in small step called counts.
During idle, the proper position of the IAC pintle is
calculated by the engine control module (ECM) based
on battery voltage, coolant temperature, engine load,
and engine speed.
If the engine speed drops below a specified value, and
the throttle plate is closed, the engine control module
(ECM) senses a near-stall condition. The engine control
module (ECM) will then calculate a new IAC pintle valve
position to prevent stalls. If the IAC valve is disconnected and reconnected with
the engine running, the idle speed will be wrong. In this
case, the IAC must be reset. The IAC resets when the
key is cycled "On" then "Off". When servicing the IAC, i
t
should only be disconnected or connected with the
ignition "Off".
The position of the IAC pintle valve affects engine start-
up and the idle characteristic of the vehicle.
If the IAC pintle is fully open, too much air will be
allowed into the manifold. This results in high idle
speed, along with possible hard starting and lean
air/fuel ratio.

Camshaft Position (CMP) Sensor








12
(1) Camshaft Position (CMP) Sensor
(2) EGR Valve


With the use of sequential multi-point fuel injection, a
hall element type camshaft position (CMP) is adopted to
provide information to be used in making decisions on
injection timing to each cylinder. It is mounted on the
rear of the left-hand cylinder head and sends signals to
the ECM.
One pulse is generated per two rotations of crankshaft.

6E-56 3.5L ENGINE DRIVEABILITY AND EMISSIONS
GENERAL DESCRIPTION FOR FUEL
METERING
The fuel metering system starts with the fuel in the fuel
tank. An electric fuel pump, located in the fuel tank,
pumps fuel to the fuel rail through an in-line fuel filter.
The pump is designed to provide fuel at a pressure
above the pressure needed by the injectors.
A fuel pressure regulator in the fuel rail keeps fuel
available to the fuel injectors at a constant pressure.
A return line delivers unused fuel back to the fuel tank.

The basic function of the air/fuel metering system is to
control the air/fuel delivery to the engine. Fuel is
delivered to the engine by individual fuel injectors
mounted in the intake manifold.
The main control sensor is the heated oxygen senso
r
located in the exhaust system. The heated oxygen
sensor reports to the ECM how much oxygen is in the
exhaust gas. The ECM changes the air/fuel ratio to the
engine by controlling the amount of time that fuel
injector is "On".
The best mixture to minimize exhaust emissions is 14.7
parts of air to 1 part of gasoline by weight, which allows
the catalytic converter to operate most efficiently.
Because of the constant measuring and adjusting of the
air/fuel ratio, the fuel injection system is called a "closed
loop" system.
The ECM monitors signals from several sensors in
order to determine the fuel needs of the engine. Fuel is
delivered under one of several conditions called
"mode". All modes are controlled by the ECM.

Acceleration Mode
The ECM provides extra fuel when it detects a rapid
increase in the throttle position and the air flow.

Battery Voltage Correction Mode
When battery voltage is low, the ECM will compensate
for the weak spark by increasing the following:

The amount of fuel delivered.

The idle RPM.

Ignition dwell time.

Clear Flood Mode
Clear a flooded engine by pushing the accelerator pedal
down all the way. The ECM then de-energizes the fuel
injectors. The ECM holds the fuel injectors de-
energized as long as the throttle remains above 80%
and the engine speed is below 800 RPM. If the throttle
position becomes less than 80%, the ECM again begins
to pulse the injectors "ON" and "OFF," allowing fuel into
the cylinders.

Deceleration Mode
The ECM reduces the amount of fuel injected when i
t
detects a decrease in the throttle position and the air
flow. When deceleration is very fast, the ECM may cu
t
off fuel completely for short periods.
Engine Speed/Vehicle Speed/Fuel Disable Mode
The ECM monitors engine speed. It turns off the fuel
injectors when the engine speed increase above 6400
RPM. The fuel injectors are turned back on when
engine speed decreases below 6150 RPM.

Fuel Cutoff Mode
No fuel is delivered by the fuel injectors when the
ignition is "OFF." This prevents engine run-on. In
addition, the ECM suspends fuel delivery if no reference
pulses are detected (engine not running) to preven
t
engine flooding.

Run Mode
The run mode has the following two conditions:

Open loop

Closed loop
When the engine is first started the system is in "open
loop" operation. In "open loop," the ECM ignores the
signal from the heated oxygen sensor (HO2S). I
t
calculates the air/fuel ratio based on inputs from the TP,
ECT, and MAF sensors.
The system remains in "open loop" until the following
conditions are met:

The HO2S has a varying voltage output showing
that it is hot enough to operate properly (this
depends on temperature).

The ECT has reached a specified temperature.


A specific amount of time has elapsed since
starting the engine.

Engine speed has been greater than a specified
RPM since start-up.
The specific values for the above conditions vary with
different engines and are stored in the programmable
read only memory (PROM). When these conditions are
met, the system enters "closed loop" operation. In
"closed loop," the ECM calculates the air/fuel ratio
(injector on-time) based on the signal from the HO2S.
This allows the air/fuel ratio to stay very close to 14.7:1.

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-57
Starting Mode
When the ignition is first turned "ON," the ECM
energizes the fuel pump relay for two seconds to allo
w
the fuel pump to build up pressure. The ECM then
checks the engine coolant temperature (ECT) senso
r
and the throttle position sensor to determine the proper
air/fuel ratio for starting.
The ECM controls the amount of fuel delivered in the
starting mode by adjusting how long the fuel injectors
are energized by pulsing the injectors for very short
times.

Fuel Metering System Components
The fuel metering system is made up of the following
parts.

Fuel injector

Throttle Body

Fuel Rail

Fuel Pressure regulator

ECM

Crankshaft position (CKP) sensor

Camshaft position (CMP) sensor

Idle air control valve

Fuel pump

Fuel Injector
The sequential multi-port fuel injection fuel injector is a
solenoid operated device controlled by the ECM. The
ECM energizes the solenoid, which opens a valve to
allow fuel delivery.
The fuel is injected under pressure in a conical spray
pattern at the opening of the intake valve. Excess fuel
not used by the injectors passes through the fuel
pressure regulator before being returned to the fuel
tank.

Fuel Pressure Regulator
The fuel pressure regulator is a diaphragm-operated
relief valve mounted on the fuel rail with fuel pump
pressure on one side and manifold pressure on the
other side. The fuel pressure regulator maintains the
fuel pressure available to the injector at three times
barometric pressure adjusted for engine load. It may be
serviced separate.
If the pressure is too low, poor performance and a DTC
P0131, P0151, P0171, P0174, P1171 or P1174 will be
the result. If the pressure is too high, excessive odo
r
and/or a DTC P0132, P0152, P0172 or P0175 will be
the result. Refer to Fuel System Diagnosisfo
r
information on diagnosing fuel pressure conditions.
Fuel Rail
The fuel rail is mounted to the top of the engine and
distributes fuel to the individual injectors. Fuel is
delivered to the fuel inlet tube of the fuel rail by the fuel
lines. The fuel goes through the fuel rail to the fuel
pressure regulator. The fuel pressure regulato
r
maintains a constant fuel pressure at the injectors.
Remaining fuel is then returned to the fuel tank.







055RV009
Fuel Pump Electrical Circuit
When the key is first turned "ON," the ECM energizes
the fuel pump relay for two seconds to build up the fuel
pressure quickly. If the engine is not started within two
seconds, the ECM shuts the fuel pump off and waits
until the engine is cranked. When the engine is cranked
and the 58 X crankshaft position signal has been
detected by the ECM, the ECM supplies 12 volts to the
fuel pump relay to energize the electric in-tank fuel
pump.
An inoperative fuel pump will cause a "no-start"
condition. A fuel pump which does not provide enough
pressure will result in poor performance.

Camshaft Position (CMP) Sensor Signal
The ECM uses this signal to determine the position o
f
the number 1 piston during its power stroke, allowing
the ECM to calculate true sequential multiport fuel
injection. Loss of this signal will set a DTC P0341. If the
CMP signal is lost while the engine is running, the fuel
injection system will shift to a calculated sequential fuel
injection based on the last fuel injection pulse, and the
engine will continue to run. The engine can be restarted
and will run in the calculated sequential mode as long
as the fault is present, with a 1-in-6 chance of being
correct.