2004 ISUZU TF SERIES injector

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-3
DTC P0201 (FLASH CODE 31) INJECTOR 1
CONTROL CIRCUIT ........................................ 6E-226
DTC P0202 (FLASH CODE 31) INJECTOR 2
CONTROL CIRCUIT ........................................ 6E-226
DTC P0203 (FLASH CODE 31) INJECTOR 3
CONTROL CIRCUIT ........................................ 6E-226
DTC P0204 (FLASH CODE 31) INJECTOR 4
CONTROL CIRCUIT ........................................ 6E-226
DTC P0205 (FLASH CODE 31) INJECTOR 5
CONTROL CIRCUIT ........................................ 6E-226
DTC P0206 (FLASH CODE 31) INJECTOR 6
CONTROL CIRCUIT ........................................ 6E-226
DTC P0336 (FLASH CODE 29) CRANKSHAFT
POSITION SENSOR CIRCUIT
RANGE/PERFORMANCE (58X) ...................... 6E-234
DTC P0337 (FLASH CODE 29) CRANKSHAFT
POSITION SENSOR CIRCUIT NO SIGNAL
(58X) ................................................................. 6E-234
DTC P0341 (FLASH CODE 41) CAMSHAFT
POSITION SENSOR CIRCUIT
RANGE/PERFORMANCE ............................... 6E-243
DTC P0342 (FLASH CODE 41) CAMSHAFT
POSITION SENSOR CIRCUIT NO SIGNAL .... 6E-243
DTC P0351 (FLASH CODE 42) IGNITION 1
CONTROL CIRCUIT ........................................ 6E-249
DTC P0352 (FLASH CODE 42) IGNITION 2
CONTROL CIRCUIT ........................................ 6E-249
DTC P0353 (FLASH CODE 42) IGNITION 3
CONTROL CIRCUIT ........................................ 6E-249
DTC P0354 (FLASH CODE 42) IGNITION 4
CONTROL CIRCUIT ........................................ 6E-249
DTC P0355 (FLASH CODE 42) IGNITION 5
CONTROL CIRCUIT ........................................ 6E-249
DTC P0356 (FLASH CODE 42) IGNITION 6
CONTROL CIRCUIT ........................................ 6E-249
DTC P0404 (FLASH CODE 32) EGR CIRCUIT
RANGE/PERFORMANCE (OPEN VALVE)....... 6E-258
DTC P1404 (FLASH CODE 32) EGR CIRCUIT
RANGE/PERFORMANCE (CLOSED VALVE) .. 6E-258
DTC P0405 (FLASH CODE 32) EGR
CIRCUIT LOW.................................................. 6E-263
DTC P0406 (FLASH CODE 32) EGR
CIRCUIT HIGH ................................................. 6E-268
DTC P0444 EVAP PURGE SOLENOID
VALVE CIRCUIT LOW VOLTAGE ................... 6E-274
DTC P0445 EVAP PURGE SOLENOID
VALVE CIRCUIT HIGH VOLTAGE .................. 6E-274
DTC P0500 (FLASH CODE 24) VEHICLE
SPEED SENSOR (VSS) CIRCUIT
RANGE/PERFORMANCE ................................ 6E-279 DTC P0562 (FLASH CODE 66) SYSTEM
VOLTAGE LOW .............................................. 6E-288
DTC P0563 (FLASH CODE 66) SYSTEM
VOLTAGE HIGH .............................................. 6E-321
DTC P0601 (FLASH CODE 51) ENGINE
CONTROL MODULE (ECM) MEMORY
CHECKSUM ..................................................... 6E-293
DTC P0602 PROGRAMMING ERROR............. 6E-295
DTC P1508 (FLASH CODE 22) IDLE AIR
CONTROL SYSTEM LOW/CLOSED ............... 6E-296
DTC P1509 (FLASH CODE 22) IDLE AIR
CONTROL SYSTEM HIGH/OPEN ................... 6E-296
DTC P1601 (FLASH CODE 65) CAN BUS
OFF .................................................................. 6E-304
DTC U2104 (FLASH CODE 67) CAN BUS
RESET COUNTER OVER-RUN ...................... 6E-310
DTC P1626 IMMOBILIZER NO SIGNAL ........... 6E-317
DTC P1631 IMMOBILIZER WRONG
SIGNAL ............................................................ 6E-323
DTC P1648 IMMOBILIZER WRONG
SECURITY CODE ENTERED .......................... 6E-325
DTC P1649 IMMOBILIZER FUNCTION NOT
PROGRAMMED ................................................ 6E-327
SYMPTOM DIAGNOSIS ................................... 6E-329
PRELIMINARY CHECKS .............................. 6E-329
VISUAL/PHYSICAL CHECK .......................... 6E-329
INTERMITTENT ............................................. 6E-329
ENGINE CRANKS BUT WILL NOT RUN ......... 6E-331
HARD START SYMPTOM ................................ 6E-334
ROUGH, UNSTABLE, OR INCORRECT
IDLE, STALLING SYMPTOM ........................... 6E-337
SURGES AND/OR CHUGS SYMPTOM ........... 6E-341
HESITATION, SAG, STUMBLE SYMPTOM ..... 6E-345
CUTS OUT, MISSES SYMPTOM ..................... 6E-347
LACK OF POWER, SLUGGISH OR SPONGY
SYMPTOM ....................................................... 6E-352
DETONATION/SPARK KNOCK SYMPTOM..... 6E-356
POOR FUEL ECONOMY SYMPTOM ............... 6E-359
EXCESSIVE EXHAUST EMISSIONS OR
ODORS SYMPTOM ......................................... 6E-362
DIESELING, RUN-ON SYMPTOM .................... 6E-365
BACKFIRE SYMPTOM ..................................... 6E-366
ON-VEHICLE SERVICE PROCEDURE ........... 6E-368
ENGINE CONTROL MODULE (ECM) .............. 6E-368
CRANKSHAFT POSITION (CKP) SENSOR ..... 6E-369
CAMSHAFT POSITION (CMP) SENSOR ......... 6E-369
ENGINE COOLANT TEMPERATURE (ECT)
SENSOR .......................................................... 6E-370
MASS AIR FLOW (MAF) SENSOR & INTAKE AIR
TEMPERATURE (IAT) SENSOR ...................... 6E-370

6E-4 3.5L ENGINE DRIVEABILITY AND EMISSIONS
THROTTLE POSITION SENSOR (TPS)........... 6E-371
IDLE AIR CONTROL (IAC) VALVE ................... 6E-371
HEATED OXYGEN SENSOR (HO2S) .............. 6E-372
EVAP CANISTER PURGE VALVE
SOLENOID ....................................................... 6E-373
FUEL PRESSURE RELIEF ............................... 6E-374
FUEL RAIL ASSEMBLY .................................... 6E-374
FUEL INJECTORS ............................................ 6E-375
FUEL PRESSURE REGULATOR ..................... 6E-377
IGNITION COIL ................................................. 6E-379
SPARK PLUGS ................................................. 6E-380
SPECIAL TOOLS .............................................. 6E-382

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-7











Legend
(1) Injector #1 Cylinder
(2) Injector #3 Cylinder
(3) Injector #5 Cylinder
(4) EGR Valve
(5) Ignition Coil #1 Cylinder
(6) Ignition Coil #3 Cylinder
(7) Ignition Coil #5 Cylinder
(8) Engine Coolant Temperature (ECT) Sensor












Legend
(1) Injector #2 Cylinder
(2) Injector #4 Cylinder
(3) Injector #6 Cylinder
(4) Idle Air Control (IAC) Valve
(5) Throttle Position Sensor
(6) Ignition Coil #2 Cylinder
(7) Ignition Coil #4 Cylinder
(8) Ignition Coil #6 Cylinder
(9) Canister Purge Solenoid Valve

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-27
CONNECTOR LIST
No. Connector face No. Connector face
B-24
Green
Meter-B C-108
WhiteJ/B E1
B-56
White
J/B I4 C-109
SilverBody-LH ; ground
B-58
Black
Check connector E-2
Magnetic clutch
B-62
White
Ignition switch (IGSUB : G1) E-6

Fuel injector
B-63
White
Ignition switch (IGSUB : G2) E-7

Fuel injector
B-68


Immobilizer E-8

Fuel injector
C-2
Silver
Engine room-RH ground E-9

Fuel injector
C-24

Triple pressure switch E-51

Fuel injector
C-94

Gray TCM-(A) E-52

Fuel injector
C-107
White
J/B E2 E-53

Ignition coil

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-45
Signal or Continuity Tester Position Pin
No.

B/Box
No.
Pin Function Wire
Color
Key SW
Off Key SW
On Engine
Idle Engine
2000rpmECM
Connection Range(+) (-)
A31 A31 No. 3 Ignition
Coil RED/
BLU - - Wave form - - - -
A32 A32 No. 1 Ignition
Coil RED - - Wave form - - - -
A33 A33 Ground (Power) BLK/
RED Continuity
with ground - - - Disconnect Ohm A33 GND
A34 A34 No. 5 Injector GRN/
BLK Less than 1V Wave form or 12-14V Connect DC V A34 GND
A35 A35 No. 3 Injector BLU Less than 1V Wave form or 12-14V Connect DC V A35 GND
A36 A36 No. 1 Injector GRN/
WHT Less than 1V Wave form or 12-14V Connect DC V A36 GND
A37 A37 Ground (Case) BLK/
RED Continuity
with ground - - - Disconnect Ohm A37 GND
A38 A38 No Connection - - - - - - - - -
A39 A39 No Connection - - - - - - - - -
A40 A40 No Connection - - - - - - - - -

6E-46 3.5L ENGINE DRIVEABILITY AND EMISSIONS

Connector B Port: View Looking Into ECM Cace





Signal or Continuity Tester Position Pin
No. B/Box
No. Pin Function Wire
Color
Key SW Off Key SW On Engine IdleEngine
2000rpm ECM
Connection Range (+) (-)
B1 B1 No Connection - - - - - - - - -
B2 B2 No Connection - - - - - - - - -
B3 B3 No. 2 Injector GRN/
ORG Less than 1V Wave form or 12-14V Connect DC V B3 GND
B4 B4 No. 4 Injector GRN/
RED Less than 1V Wave form or 12-14V Connect DC V B4 GND
B5 B5 No. 6 Injector GRN/
YELLess than 1V Wave form or 12-14V Connect DC V B5 GND
B6 B6 Ground
(Power) BLK Continuity
with ground - - - Disconnect Ohm B6 GND
B7 B7 No. 2 Ignition
Coil RED/
BLK- - Wave form - - - -
B8 B8 No. 4 Ignition
Coil RED/
WHT - - Wave form - - - -
B9 B9 No. 6 Ignition
Coil RED/
GRN - - Wave form - - - -
B10 B10 No Connection - - - - - - - - -
B11 B11 A/C
Compressor
Relay GRY/
RED Less than 1V A/C comp. is operated: Less than 1V
A/C comp. is not operated: 10-14V Connect DC V B11 GND
B12 B12 Tachometer
Output Signal BLK/
RED - - Wave form or
6.2V Wave form or
6.2V Connect AC V B12 GND
B13 B13 Idle Air Control
(IAC) Valve
Coil A High BLU Less than 1V Less than 1V / 10-14V Connect DC V B13 GND
B14 B14 Idle Air Control
(IAC) Valve
Coil B High BLU/
WHT Less than 1V Less than 1V / 10-14V Connect DC V B14 GND
B15 B15 Canister Purge
Solenoid Valve RED/
BLULess than 1V Wave form or 12-14V Connect AC V B15 GND

6E-50 3.5L ENGINE DRIVEABILITY AND EMISSIONS

Injector Control Signal Reference Wave Form











0V






Measurement Terminal: A36(+) (No.1 Cylinder) GND(-)
Measurement Scale: 20V/div 10ms/div
Measurement Condition: Approximately 2000rpm
Ignition Coil Control Signal Reference Wave Form









0V








Measurement Terminal: A32(+) (No.1 Cylinder) GND(-)
Measurement Scale: 5V/div 10ms/div
Measurement Condition: Approximately 2000rpm
Injector & Ignition Coil Control Signal Reference Wave Form










CH1
0V


CH2
0V


Measurement Terminal: CH1: A36(+) (No.1 Cylinder)
CH2: A32(+) (No.1 Cylinder) GND(-)
Measurement Scale: CH1: 20V/div / CH2: 5V/div 10ms/div
Measurement Condition: Approximately 2000rpm
EVAP Canistor Purge Solenoid Reference Wave Form









0V








Measurement Terminal: B15(+) GND(-)
Measurement Scale: 10V/div 20ms/div
Frequency: Approximately 16Hz
EGR Solenoid Reference Wave Form









0V








Measurement Terminal: CH1: A5(+) GND(-)
Measurement Scale: CH1: 10V/div 2ms/div
Frequency: Approximately 128Hz

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-55
Vehicle Speed Sensor (VSS)



The VSS is a magnet rotated by the transmission output
shaft. The VSS uses a hall element. It interacts with the
magnetic field treated by the rotating magnet. It outputs
pulse signal. The 12 volts operating supply from the
meter fuse.
Heated Oxygen (O2) Sensor




1
(1) Bank 1 Heated Oxygen Sensor (RH)






1
(1) Bank 2 Heated Oxygen Sensor (LH)

Each oxygen sensor consists of a 4-wire low
temperature activated zirconia oxygen analyzer elemen
t
with heater for operating temperature of 315C, and
there is one mounted on each exhaust pipe.
A constant 450millivolt is supplied by the ECM between
the two supply terminals, and oxygen concentration in
the exhaust gas is reported to the ECM as returned
signal voltage.
The oxygen present in the exhaust gas reacts with the
sensor to produce a voltage output. This voltage should
constantly fluctuate from approximately 100mV to
1000mV and the ECM calculates the pulse width
commanded for the injectors to produce the prope
r
combustion chamber mixture.
Low oxygen sensor output voltage is a lean mixture
which will result in a rich commanded to compensate.
High oxygen sensor output voltage is a rich mixture
which result in a lean commanded to compensate.
When the engine is first started the system is in "Open
Loop" operation. In "Open Loop", the ECM ignores the
signal from the oxygen sensors. When various
conditions (ECT, time from start, engine speed &
oxygen sensor output) are met, the system enters
"Closed Loop" operation. In "Closed Loop", the ECM
calculates the air fuel ratio based on the signal from the
oxygen sensors.

Heated oxygen sensors are used to minimize the
amount of time required for closed loop fuel control to
begin operation and allow accurate catalyst monitoring.
The oxygen sensor heater greatly decreases the
amount of time required for fuel control sensors to
become active.
Oxygen sensor heaters are required by catalyst monito
r
and sensors to maintain a sufficiently high temperature
which allows accurate exhaust oxygen content readings
further away from the engine.