2004 ISUZU TF SERIES wheel

5A-28 BRAKE CONTROL SYSTEM

Isolation Valve Test
Purpose: The purpose of this test is to detect brake
pipe and valve line harness wire for wrong connections
and valve trouble.
This test will help you confirm the result of your repair
service including the removal/reinstallation of brake
pipe, valve line harness and valve.
Test conditions: The ignition key is in the “ON” position
with the four wheels lifted up. The brake pedal is
stepped on, released and stepped on again with the
parking brake released.
Test procedure:
1. Connect Tech 2 with the vehicle, and select
Actuaor Test from the menus.
2. Select a Solenoid Valve Test Menu from the
Actuaor Test Menus.

060L300002
3. Select Isolation Valve from the Valve Select Menus.
4. Step on the brake pedal.
5. Release the brake pedal.
6. Make sure that the Isolation Valve “ON” aimed at by
Tech 2 and the wheel locked position are the same.
If different, check brake pipe, valve line harness
wiring and H/UNIT. Repair is needed if abnormality
is found.
7. Conduct Step 2 through Step 5 above on all the
four wheels.

060L300002
CAUTION: When conducting this test, please
observe the following cautions.

1. Do not start the engine.
2. Lift up the vehicle at a level floor.





Secure a clearance from the floor surface
enough to allow the lifted tire to rotate.
3. Maintain the lift up.
4. Wipe the floor surface to remove water and oil
so that the surface may become unslippery.
5. Do not load the vehicle.





When lifting up the vehicle, be sure to
observe the lifting up points. Refer to
vehicle lifting points in 0A section.

BRAKE CONTROL SYSTEM 5A-29

Dump Valve Test
Purpose: The purpose of this test is to detect brake
pipe and valve line harness wire for wrong connections
and valve trouble.
This test will help you confirm the result of your repai
r
service including the removal/reinstallation of brake
pipe, valve line harness and valve.
Test conditions: The ignition key is in the “ON” position
with the four wheels lifted up. The brake pedal is
stepped on, released and stepped on again with the
parking brake released.
Test procedure:
1. Connect Tech 2 with the vehicle, and select
Actuator Test Function from the menus.
2. Select a Solenoid Valve Test Menu from the
Actuator Test Menus.

060L300002
3. Select Dump Valve from the Valve Select Meuns.
4. Step on the brake pedal.
5. Make sure that the Dump Valve “ON” aimed at by
Tech 2 and the wheel released position are the
same. If different, check brake pipe, valve line
harness wiring and H/UNIT. Repair is needed if
abnormality is found.
6. Conduct Step 2 through Step 5 above on all the
four wheels.

060L300002
CAUTION: When conducting this test, please
observe the following cautions.

1. Do not start the engine.
2. Lift up the vehicle at a level floor.





Secure a clearance from the floor surface
enough to allow the lifted tire to rotate.
3. Maintain the lift up.
4. Wipe the floor surface to remove water and oil
so that the surface may become unslippery.
5. Do not load the vehicle.





When lifting up the vehicle, be sure to
observe the lifting up points. Refer to
vehicle lifting points in 0A section.

5A-30 BRAKE CONTROL SYSTEM

Diagnostic Trouble Codes
Choose and trace an appropriate flowchart by the
numbers listed below to find fault and repair.
Note:
DTC cannot be erased when the DTC is a present.

Warning Lamp System Control Main Items
DTC
(Flash
Code) Description
ABS Brake
(EBD)ABS EBD
-
(12) Normal Condition




-
C0221
(21) Front Right Wheel Speed Sensor Short
Circuit or Circuit Open

*A

Sensor or Wiring
C0222
(22) Front Right Wheel Speed Sensor
Incorrect Signal *B

A

Sensor or install condition
C0223
(23) Front Right Wheel Speed Sensor Signal
- Tooth Chipping

*A

Sensor Rotor or install
condition
C0225
(25) Front Left Wheel Speed Sensor Short
Circuit or Circuit Open

*A

Sensor or Wiring
C0226
(26) Front Left Wheel Speed Sensor
Incorrect Signal *B

*A

Sensor or install condition
C0227
(27) Front Left Wheel Speed Sensor Signal -
Tooth Chipping

*A

Sensor Rotor or install
condition
C0231
(31) Rear Right Wheel Speed Sensor Short
Circuit or Circuit Open

*A

Sensor or Wiring
C0232
(32) Rear Right Wheel Speed Sensor
Incorrect Signal *B

*A

Sensor or install condition
C0233
(33) Rear Right Wheel Speed Sensor Signal
- Tooth Chipping

*A

Sensor Rotor or install
condition
C0235
(35) Rear Left Wheel Speed Sensor Short
Circuit or Circuit Open

*A

Sensor or Wiring
C0236
(36) Rear Left Wheel Speed Sensor
Incorrect Signal *B

*A

Sensor or install condition
C0237
(37) Rear Left Wheel Speed Sensor Signal -
Tooth Chipping

*A

Sensor Rotor or install
condition
C0238
(38) Tire Diameter Error



Vehicle , Sensor or Tire
C0241
(41) Front Right Isolation Solenoid Circuit
Open or Shorted to Ground



Solenoid (EHCU)
C0242
(42) Front Right Dump Solenoid Circuit
Open or Shorted to Ground



Solenoid (EHCU)
C0243
(43) Front Right Isolation Solenoid Circuit
Shorted to Battery



Solenoid (EHCU)
C0244
(44) Front Right Dump Solenoid Circuit
Shorted to Battery



Solenoid (EHCU)
C0245
(45) Front Left Isolation Solenoid Open Or
Shorted to Ground



Solenoid (EHCU)
C0246
(46) Front Left Dump Solenoid Circuit Open
Or Shorted to Ground



Solenoid (EHCU)
C0247
(47) Front Left Isolation Solenoid Circuit
Shorted to Battery



Solenoid (EHCU)

BRAKE CONTROL SYSTEM 5A-31

Warning Lamp System Control Main Items DTC
(Flash
Code) Description
ABS Brake
(EBD)ABS EBD
C0248
(48) Front Left Dump Solenoid Circuit
Shorted to Battery



Solenoid (EHCU)
C0251
(51) Rear Isolation Solenoid Circuit Open or
Shorted to Ground



Solenoid (EHCU)
C0252
(52) Rear Dump Solenoid Circuit Open or
Shorted to Ground



Solenoid (EHCU)
C0253
(53) Rear Isolation Solenoid Circuit Shorted
to Battery



Solenoid (EHCU)
C0254
(54) Rear Dump Solenoid Circuit Shorted to
Battery



Solenoid (EHCU)
C0265
(65) Fail Safe Relay (FSR) Shorted to
Ground



Motor (EHCU)
C0266
(66) Fail Safe Relay (FSR) Shorted to
Battery



Relay (EHCU)
C0267
(67) ABS Motor Shorted to Ground



Motor (EHCU)
C0268
(68) ABS Motor Shorted to Battery



Motor (EHCU)
C0271
(71) ECU Failure or Valve +B Circuit Open



EHCU
C0274
(74) ABS Operation Long Time



EHCU

C0276
(76) G-Sensor Malfunction



Sensor or Wiring




Battery, Wiring or EHCU
(less than 9V) C0277
(77) Power Supply Low Input




Battery or Wiring
(less than 10V)
C0278
(78) Power Supply High Input



Battery or Wiring EHCU
C0282
(82) 4 Wheel Drive State Input Signal Failure



Wiring
C0285
(85) Assembly Error (G-sensor)



Vehicle (Sensor or EHCU)

*A : When three or more failure are detected, or when
failure containing both front wheels and each rear
wheels are detected, EBD warning lamp is "ON"
and control is canceled.
*B : ABS lamp is “OFF” when the ABS lamp is “ON”
after a repair until vehicles speed becomes more
than 6km/h (4mph) in the following ignition cycle
and failure is not detected.

BRAKE CONTROL SYSTEM 5A-33

How to display and erase DTCs:
Note:
 DTCs can be displayed also by TECH 2 use
“Diagnostic Trouble Codes“ mode.
1. How to start DTC display:
 Confirm that the vehicle has come to a
complete stop (with the wheels standing still)
and that the brake pedal is not depressed.
(Unless these two condition are satisfied, DTC
display cannot be started.)
 With IGN OFF, connect #12 terminal with #4
terminal or # 5 terminal (GND) . Then turn IGN
ON.

The DLC is located behind the driver side kick panel

















This illustration is based on RHD model
350L300005

 Keep #12 terminal connected with #4 terminal
or # 5 terminal (GND) during DTC display. (If
#12 terminal is separated from #4 terminal or #
5 terminal (GND) during display, display will
stop.)
2. DTC display:
 DTC is displayed by blinking warning lamp.
 Double-digit display.
 First, normal DTC 12 is displayed three times
and then any other DTCs are displayed three
times. (If no other DTCs have been stored, the
display of DTC 12 will be repeated.)
3. How to erase code:
 Conduct brake switch ON/OFF operation 6 or
more times within 3 seconds of self-diagnosis
startup.
 The code cannot be erased if more than 3
seconds have passed since self-diagnosis
startup, or if self-diagnosis has started with
brake switched on (brake pedaled).
B05RW0005

5A-34 BRAKE CONTROL SYSTEM

4. Notes
 If the following should occur during Diagnostic
Trouble Code (DTC) display, the display will be
discontinued. After initial check, the status that
is under the control of ABS will be returned :
– The vehicle starts (The wheels turn) or the
brake pedal is depressed.
 Up to 3 different codes can be stored.
 If the ABS should turn OFF due to an
intermittent defect, the system will be restored
at the next key cycle, if the initial check finds no
abnormality (when IGN is switched from OFF to
ON).
5. An example of DTC display
Display of DTC 23

B05R100001
After displaying DTC 12 three times, one DTC after
another is displayed. DTC is displayed on small
order.

C05L300017
The DTC 12 is displayed repeatedly.

5A-38 BRAKE CONTROL SYSTEM

Wheel Speed Sensor Inspection Procedure
Procedure
1.Ignition "OFF".
2.Disconnect the each wheel speed sensors.
3.Check the voltage at sensor harness connector.
Note : Voltage measurement is performed in the phase
where the wheel speed sensor is installed in vehicles.

C05L300019
Connector Pin-outs

Front Wheel Speed Sensor
1 (+) (+12V)
2 (-) (signal)

Rear Wheel Speed Sensor
1 LH (+) (+12V)
2 LH (-) (signal)
3 RH (+)(+12V)
4 RH (-) (signal)






Output Value
High State 1.28~2.2V
Low State 0.5~0.86V
High-Low
Difference more than 0.8V

BRAKE CONTROL SYSTEM 5A-39

Symptom Diagnosis
The symptoms that cannot be indicated by warning
lamp can be divided in the following five categories:
1. ABS works frequently but vehicle does not
decelerate.
2. Uneven braking occurs while ABS works.
3. The wheels are locked.

4. Brake pedal feel is abnormal.
5. Braking sound (from EHCU) is heard while not
braking.
6. No ABS warning lamp
These are all attributable to problems which cannot be
detected by EHCU self-diagnosis. Use the customer
complaint and a test to determine which symptom is
present.
ABS Works Frequently But Vehicle Does Not Decelerate

Step Action
Value(s) Yes No
1 Is braking force distribution normal between front
and rear of vehicle?
- Go to Step 2 Repair brake
parts.
Go to Step 7
2 Are axle parts installed normally?
- Go to Step 3 Repair axle
parts.
Go to Step 7
3 Is there play in each or any wheel speed sensor?
- Repair wheel
speed sensor.
Go to Step 7 Go to Step 4
4 Is there damage, or powered iron sticking to each or
any wheel speed sensor/sensor rotor?
- Replace
wheel speed
sensor or
sensor rotor.
Go to Step 8 Go to Step 5
5 Is the each wheel speed sensor output normal?
- Go to Step 6 Replace
wheel speed
sensor or
repair
harness.
Go to Step 7
6 Is the 4WD control system function normal?
- 2-4WD Repair
or Go to Step
7 Repair or
replace 2-
4WD control
System.
Go to Step 7
7 Reconnect all components, ensure all components
are properly mounted.
Was this step finished?
- Repeat the
“Basic
diagnostic
flow chart” Go to Step 7