2004 INFINITI QX56 Ins

AT-84
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
44
Slips/Will
Not
EngageVehicle cannot run in
all positions.ON vehicle1. Fluid level and stateAT-5 8
2. Line pressure testAT-5 9
3. PNP switchAT- 1 0 9
4. Control cable adjustmentAT- 2 3 4
5. Control valve with TCMAT- 2 4 1
OFF vehicle6. Oil pump assemblyAT- 2 9 07. Gear systemAT- 2 6 1
8. Output shaftAT- 2 7 3
45With selector lever in
“D” position, driving is
not possible.ON vehicle1. Fluid level and stateAT-5 8
2. Line pressure testAT-5 9
3. PNP switchAT- 1 0 9
4. Control cable adjustmentAT- 2 3 4
5. Control valve with TCMAT- 2 4 1
OFF vehicle6. Torque converterAT- 2 7 3
7. Oil pump assembly AT- 2 9 0
8. 1st one-way clutchAT- 3 0 0
9. Gear systemAT- 2 6 1
10. Reverse brakeAT- 2 7 3
11. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT-1 8
, AT- 1 9 .)AT- 2 7 3
12. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 8
, AT- 1 9
.)AT- 2 7 3
46With selector lever in
“R” position, driving is
not possible.ON vehicle1. Fluid level and stateAT-5 8
2. Line pressure testAT-5 9
3. PNP switchAT- 1 0 9
4. Control cable adjustmentAT- 2 3 4
5. Control valve with TCMAT- 2 4 1
OFF vehicle6. Gear systemAT- 2 6 17. Output shaftAT- 2 7 3
8. Reverse brakeAT- 2 7 3
47 OthersShift point is high in
“D” position.ON vehicle1. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2
,
AT- 1 3 6
2. Accelerator pedal position sensorAT- 1 2 9
3. CAN communication lineAT- 1 0 3
4. ATF temperature sensorAT- 1 3 1
5. Control valve with TCMAT- 2 4 1
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-85
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
48
OthersShift point is low in “D”
position.ON vehicle1. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2
,
AT- 1 3 6
2. Accelerator pedal position sensorAT- 1 2 9
3. CAN communication lineAT- 1 0 3
4. Control valve with TCMAT- 2 4 1
49Judder occurs during
lock-up.ON vehicle1. Fluid level and stateAT- 5 8
2. Engine speed signalAT- 11 5
3. Turbine revolution sensorAT- 1 3 4
4. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
5. Accelerator pedal position sensorAT- 1 2 9
6. CAN communication lineAT- 1 0 3
7. Torque converter clutch solenoid valveAT- 11 8
8. Control valve with TCMAT- 2 4 1
OFF vehicle 9. Torque converterAT- 2 7 3
50Strange noise in “R”
position.ON vehicle1. Fluid level and stateAT- 5 8
2. Engine speed signalAT- 11 5
3. CAN communication lineAT- 1 0 3
4. Control valve with TCMAT- 2 4 1
OFF vehicle5. Torque converterAT- 2 7 3
6. Oil pump assemblyAT- 2 9 0
7. Gear systemAT- 2 6 1
8. High and low reverse clutchAT- 3 0 5
9. Reverse brakeAT- 2 7 3
51Strange noise in “N”
position.ON vehicle1. Fluid level and stateAT- 5 8
2. Engine speed signalAT- 11 5
3. CAN communication lineAT- 1 0 3
4. Control valve with TCMAT- 2 4 1
OFF vehicle5. Torque converterAT- 2 7 36. Oil pump assemblyAT- 2 9 0
7. Gear systemAT- 2 6 1
52Strange noise in “D”
position.ON vehicle1. Fluid level and stateAT- 5 8
2. Engine speed signalAT- 11 5
3. CAN communication lineAT- 1 0 3
4. Control valve with TCMAT- 2 4 1
OFF vehicle5. Torque converterAT- 2 7 3
6. Oil pump assemblyAT- 2 9 0
7. Gear systemAT- 2 6 1
8. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-1 8
, AT - 1 9
.)AT- 2 7 3
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-87
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
56
OthersMaximum speed low.ON vehicle1. Fluid level and stateAT- 5 8
2. Line pressure testAT- 5 9
3. Accelerator pedal position sensorAT- 1 2 9
4. CAN communication lineAT- 1 0 3
5. Direct clutch solenoid valveAT- 1 5 7
6. Control valve with TCMAT- 2 4 1
OFF vehicle7. Torque converterAT- 2 7 3
8. Oil pump assemblyAT- 2 9 0
9. Input clutchAT- 2 9 5
10. Gear systemAT- 2 6 1
11. High and low reverse clutchAT- 3 0 5
12. Direct clutchAT- 3 0 7
13. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT- 1 8
, AT-1 9 .)AT- 2 7 3
14 Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-1 8
, AT - 1 9
.)AT- 2 7 3
57Extremely large
creep.ON vehicle1. Engine idle speed EC-32

2. CAN communication lineAT- 1 0 3
3. ATF pressure switch 5AT- 1 8 1
OFF vehicle 4. Torque converterAT- 2 7 3
58With selector lever in
“P” position, vehicle
does not enter parking
condition or, with
selector lever in
another position, park-
ing condition is not
cancelled.
Refer to AT- 1 9 3 , "
In
“P” Position, Vehicle
Moves When Pushed"
.ON vehicle1. PNP switchAT- 1 0 9
2. Control cable adjustmentAT- 2 3 4
3. Parking pawl componentsAT- 2 6 1
59Vehicle runs with
transmission in “P”
position.ON vehicle1. PNP switchAT- 1 0 9
2. Fluid level and stateAT- 5 8
3. Control cable adjustmentAT- 2 3 4
4. Control valve with TCMAT- 2 4 1
5. Parking pawl componentsAT- 2 6 1
OFF vehicle 6. Gear systemAT- 2 6 1
No. Items Symptom Condition Diagnostic ItemReference
page

AT-88
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
60
OthersVehicle runs with
transmission in “N”
position.
Refer to AT-194, "In
“N” Position, Vehicle
Moves" .ON vehicle1. PNP switchAT- 1 0 9
2. Fluid level and stateAT-5 8
3. Control cable adjustmentAT- 2 3 4
4. Control valve with TCMAT- 2 4 1
OFF vehicle5. Input clutchAT- 2 9 5
6. Gear systemAT- 2 6 1
7. Direct clutchAT- 3 0 7
8. Reverse brakeAT- 2 7 3
9. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT-1 8
, AT- 1 9 .)AT- 2 7 3
10. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 8
, AT- 1 9
.)AT- 2 7 3
61Engine does not start
in “N” or “P” position.
Refer to AT-192, "Engine Cannot Be
Started In “P” or “N”
Position" .ON vehicle1. Ignition switch and starterPG-4
, SC-
10
2. Control cable adjustmentAT- 2 3 4
3. PNP switchAT- 1 0 9
62Engine starts in posi-
tions other than “N” or
“P”.ON vehicle1. Ignition switch and starterPG-4
, SC-
10
2. Control cable adjustmentAT- 2 3 4
3. PNP switchAT- 1 0 9
63 Engine stall.ON vehicle1. Fluid level and stateAT-5 8
2. Engine speed signalAT - 11 5
3. Turbine revolution sensorAT- 1 3 4
4. Torque converter clutch solenoid valveAT - 11 8
5. CAN communication lineAT- 1 0 3
6. Control valve with TCMAT- 2 4 1
OFF vehicle 7. Torque converterAT- 2 7 3
64Engine stalls when
select lever shifted “N”
→ “D”, “R”.ON vehicle1. Fluid level and stateAT-5 8
2. Engine speed signalAT - 11 5
3. Turbine revolution sensorAT- 1 3 4
4. Torque converter clutch solenoid valveAT - 11 8
5. CAN communication lineAT- 1 0 3
6. Control valve with TCMAT- 2 4 1
OFF vehicle 7. Torque converterAT- 2 7 3
No. Items Symptom Condition Diagnostic ItemReference
page

AT-90
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
TCM Input/Output Signal Reference ValuesUCS002D7
A/T ASSEMBLY TERMINAL CONNECTOR LAYOUT
TCM INSPECTION TABLE
Data are reference value and are measured between each terminal and ground.
SCIA1658E
Terminal
No.Wire
colorItem Condition Data (Approx.)
1PPower supply
(Memory back-up)– Battery voltage
2PPower supply
(Memory back-up)– Battery voltage
3 W CAN-H – –
4VK-line (CONSULT-
II signal)The terminal is connected to the data link connector for CONSULT-II. –
5 B Ground – –
6Y/RPower supply– Battery voltage
–0V
7RBack-up lamp
relaySelector lever in “R” position. 0V
Selector lever in other positions. Battery voltage
8 R CAN-L – –
9 B/R Starter relaySelector lever in “N”,“ P” positions. Battery voltage
Selector lever in other positions. 0V
10 B Ground – –

TROUBLE DIAGNOSIS
AT-91
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
CONSULT-II Function (A/T)UCS002D8
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II REFERENCE VALUE
NOTICE:
1. The CONSULT-II electrically displays shift timing and lock-up timing (that is, operation timing of each sole-
noid).
Check for time difference between actual shift timing and the CONSULT-II display. If the difference is
noticeable, mechanical parts (except solenoids, sensors, etc.) may be malfunctioning. Check mechanical
parts using applicable diagnostic procedures.
2. Shift schedule (which implies gear position) displayed on CONSULT-II and that indicated in Service Man-
ual may differ slightly. This occurs because of the following reasons:
–Actual shift schedule has more or less tolerance or allowance,
–Shift schedule indicated in Service Manual refers to the point where shifts start, and
–Gear position displayed on CONSULT-II indicates the point where shifts are completed.
3. Display of solenoid valves on CONSULT-II changes at the start of shifting, while gear position is displayed
upon completion of shifting (which is computed by TCM).
TCM diagnostic mode Description
WORK SUPPORTSupports inspections and adjustments. Commands are transmitted to the TCM for setting the status
suitable for required operation, input/output signals are received from the TCM and received data is
displayed.
SELF-DIAG RESULTS Displays TCM self-diagnosis results.
DATA MONITOR Displays TCM input/output data in real time.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
FUNCTION TESTConducted by CONSULT-II instead of a technician to determine whether each system is “OK” or
“NG”.
ECU PART NUMBER TCM part number can be read.
Item name Condition Display value
AT F T E M P S E 1
0°C (32° F) - 20°C (68°F) - 80°C (176°F)3.2 - 2.5 - 0.8 V
AT F T E M P S E 23.2 - 2.4 - 0.65 V
TCC SOLENOIDWhen perform slip lock-up 0.2 - 0.4 A
When perform lock-up 0.4 - 0.6 A
SLCT LVR POSISelector lever in “N”,“P” position. N/P
Selector lever in “R” position. R
Selector lever in “D” position. D
Selector lever in “4” position. 4
Selector lever in “3” position. 3
Selector lever in “2” position. 2
Selector lever in “1” position. 1
VHCL/S SE·A/T During driving Approximately matches the
speedometer reading.
ENGINE SPEED Engine running Closely matches the tachometer
reading.
LINE PRES SOL During driving 0.2 - 0.6 A
TURBINE REV During driving (lock-up ON) Approximately matches the
engine speed.
VHCL/S SE·MTR During driving Approximately matches the
speedometer reading.

TROUBLE DIAGNOSIS
AT-93
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
CONSULT-II SETTING PROCEDURE
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.

For details, refer to the separate “CONSULT-II Operations Man-
ual”.
1. Turn ignition switch “OFF”.
2. Connect CONSULT-II and CONSULT-II CONVERTER to data
link connector, which is located in instrument lower panel on
driver side.
3. Turn ignition switch “ON”. (Do not start engine.)
4. Touch “START (NISSAN BASED VHCL)”.
5. Touch “A/T”.
If “A/T” is not indicated, go to GI-39, "
CONSULT-II Data Link
Connector (DLC) Circuit" .
6. Perform each diagnostic test mode according to each service
procedure.
SELF-DIAGNOSTIC RESULT MODE
Operation Procedure
1. Perform “CONSULT-II SETTING PROCEDURE” Refer to AT-93, "CONSULT-II SETTING PROCEDURE"
.
2. Touch “SELF-DIAG RESULTS”.
Display shows malfunction experienced since the last erasing
operation.
BBIA0369E
BCIA0029E
BCIA0030E
BCIA0031E

AT-102
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
7. Perform test drive to check gear shift feeling in accordance with
instructions displayed.
8. Touch “YES” or “NO”.
9. CONSULT-II procedure is ended.

If “NG” appears on the screen, a malfunction may exist.
Go to “Diagnostic Procedure”.
Display Items List
*: Do not use, but displayed.
SCIA5163E
SCIA5162E
DTC work support item Description Check item
I/C SOL FUNCTN CHECK* — —
FR/B SOL FUNCTN CHECK* — —
D/C SOL FUNCTN CHECK* — —
HLR/C SOL FUNCTN CHECK* — —
LC/B SOL FUNCTN CHECK* — —
TCC SOL FUNCTN CHECKFollowing items for “TCC solenoid function (lock-up) ” can be con-
firmed.

Self-diagnosis status (whether the diagnosis is being conducted
or not)

Self-diagnosis result (OK or NG)

TCC solenoid valve

Hydraulic control circuit