2004 INFINITI QX56 bulb

LT-94
TURN SIGNAL AND HAZARD WARNING LAMPS
Revision: August 20072004 QX56
Bulb Replacement (Front Turn Signal Lamp)EKS007BU
1. Remove turn/fog lamp assembly. Refer to LT- 7 9 , "Removal and Installation" .
2. Turn bulb socket counterclockwise to remove it from lamp housing.
3. Pull bulb from socket.
Installation is in the reverse order of removal.
Bulb Replacement (Rear Turn Signal Lamp)EKS007BV
Refer to LT- 1 2 2 , "Bulb Replacement (Turn Signal)" in REAR COMBINATION LAMP.
Removal and Installation of Front Turn Signal LampEKS007BW
Refer to LT- 3 3 , "Removal and Installation" .
Removal and Installation of Rear Turn Signal Lamp EKS007BX
Refer to LT- 1 2 2 , "Removal and Installation" in REAR COMBINATION LAMP.

STOP LAMP
LT-105
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: August 20072004 QX56
High-Mounted Stop LampEKS007C8
BULB REPLACEMENT
The high-mounted stop lamp bulbs are not serviceable.
REMOVAL AND INSTALLATION
1. Remove back door upper finisher.
2. Remove 2 nuts and remove high-mounted stop lamp.
Installation is in the reverse order of removal.
Stop LampEKS007C9
BULB REPLACEMENT
The stop lamp bulbs are not serviceable separately. Replace rear combination lamp. Refer to LT-122,
"Removal and Installation" .
REMOVAL AND INSTALLATION
Refer to LT-122, "Removal and Installation" in REAR COMBINATION LAMP.
WKIA1397E

BACK-UP LAMP
LT-107
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: August 20072004 QX56
Bulb ReplacementEKS007CB
1. Remove back door lower finisher. Refer to EI-41, "Removal and Installation" .
2. Turn bulb socket counterclockwise and remove it from the lamp housing.
3. Pull bulb from socket.
Installation is in the reverse order of removal.
Removal and InstallationEKS007CC
1. Remove license lamp finisher. Refer to EI-24, "Removal and Installation" .
2. Carefully release tabs to remove back up lamp housing from
license plate finisher.
Installation is in the reverse order of removal.
WKIA1898E

LT-120
PARKING, LICENSE PLATE AND TAIL LAMPS
Revision: August 20072004 QX56
6. CHECK GROUND
1. Check continuity between front combination lamp harness con-
nector and ground.
2. Check continuity between license lamps plate harness connec-
tor and ground.
3. Check continuity between rear combination lamp harness con-
nector and ground.
OK or NG
OK >> Check bulbs.
NG >> Repair harness or connector.
Parking, License Plate and Tail Lamps Do Not Turn OFF (After Approx. 10 Min-
utes)
EKS007CO
1. CHECK IPDM E/R
1. Turn ignition switch ON. Turn the combination switch (lighting switch) to the OFF position. Turn ignition
switch OFF.
2. Verify that the parking, license plate, and tail lamps turn on and off after approximately 10 minutes.
OK or NG
OK >> Ignition relay malfunction. Refer to PG-18, "Function of Detecting Ignition Relay Malfunction" .
NG >> Inspection End.
Front combination lamp
Continuity
ConnectorTe r m i n a l
(wire color)
RH E107
4 (B) Ground Yes
LH E11
WKIA1904E
License plate lamps
Continuity
ConnectorTerminal
(wire color)
D703 – (B) Ground Yes
WKIA1080E
Rear combination lamp
Continuity
ConnectorTe r m i n a l
(wire color)
RH B130
1 (B) Ground Yes
LH B70
WKIA1905E

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-121
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: August 20072004 QX56
Front Parking LampEKS007CP
BULB REPLACEMENT
For bulb replacement, refer to LT- 3 2 , "FRONT PARKING LAMP (INNER OR OUTER)" or LT-32, "FRONT
SIDE MARKER LAMP" .
Tail LampEKS007CQ
BULB REPLACEMENT
The tail lamp bulbs are not serviceable separately. Replace rear combination lamp. Refer to LT-122, "Removal
and Installation" .
License Plate LampEKS007TR
BULB REPLACEMENT
1. Remove back door lower finisher. Refer to EI-41, "Removal and Installation" .
2. Turn bulb socket counterclockwise to remove it.
3. Pull bulb from socket.
Installation is in the reverse order of removal.

LT-122
REAR COMBINATION LAMP
Revision: August 20072004 QX56
REAR COMBINATION LAMPPFP:26554
Bulb Replacement (Turn Signal)EKS007CR
NOTE:
The tail/stop lamp bulbs are LEDs and are not serviceable separately.
1. Remove rear combination lamp mounting bolts.
2. Pull rear combination lamp to remove from the vehicle.
3. Turn bulb socket counterclockwise and unlock it.
4. Remove bulb.
Installation is in the reverse order of removal.
Removal and InstallationEKS007CS
1. Remove rear combination lamp mounting bolts.
2. Pull rear combination lamp to remove from the vehicle.
3. Disconnect rear combination lamp connectors.
Installation is in the reverse order of removal.
WKIA1393E
Rear combination lamp
mounting bolts: 2.4 Nm (0.24 kg-m, 21 in-lb)
WKIA1393E

INTERIOR ROOM LAMP
LT-151
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: August 20072004 QX56
4. CHECK IGNITION KEYHOLE ILLUMINATION BULB
1. Disconnect ignition keyhole illumination connector.
2. Check continuity between ignition keyhole illumination terminals
+ and –.
OK or NG
OK >> GO TO 5.
NG >> Replace ignition keyhole illumination.
5. CHECK IGNITION KEYHOLE ILLUMINATION CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector M18 terminal
1 (BR/W) and keyhole illumination harness connector M150 ter-
minal – (BR/W).
OK or NG
OK >> Replace BCM if ignition keyhole illumination does not
work after setting the connector again. Refer to BCS-19,
"Removal and Installation of BCM" .
NG >> Repair harness or connector.
6. CHECK IGNITION KEYHOLE ILLUMINATION CIRCUIT
1. Disconnect BCM connector and keyhole illumination connector.
2. Check continuity between BCM harness connector M19 terminal
56 (R/G) and keyhole illumination harness connector M150 ter-
minal + (R/G).
OK or NG
OK >> Replace BCM if ignition keyhole illumination does not
work after setting the connector again. Refer to BCS-19,
"Removal and Installation of BCM" .
NG >> Repair harness or connector.Continuity should exist.
WKIA1910E
Continuity should exist.
WKIA1911E
Continuity should exist.
WKIA1912E

LT-170
BULB SPECIFICATIONS
Revision: August 20072004 QX56
BULB SPECIFICATIONSPFP:26297
HeadlampEKS007DF
*: Always check with the Parts Department for the latest parts information.
Exterior LampEKS007DG
*: Always check with the Parts Department for the latest parts information.
Interior Lamp/IlluminationEKS007DH
*: Always check with the Parts Department for the latest parts information.Item Wattage (W)*
Low35 (D2R)
High60 (HB3)
Item Wattage (W)*
Front combination lampParking lamp (Inner) 7
Parking lamp (Outer) 7
Side marker 7
Rear combination lampStop/Tail lamp *
Side marker lamp *
Turn signal lamp 27
Back-up lamp18
Turn/fog lampFog 55 (H3)
Tu rn 2 1
License plate lamp5
High-mounted stop lamp*
Item Wattage (W)*
Glove box lamp3.4
Room/Map lamp8
Console box illumination lamp*
A/T device lamp2
Foot lamp3.4
Ste p la mp3.8
Cargo lamp7
Vanity lamp1.32
Personal lamp5
Puddle lamp8
Ignition keyhole illumination lamp0.74