2004 INFINITI QX56 brake sensor

AT-34
A/T CONTROL SYSTEM
Revision: August 20072004 QX56
During Shift Change
The necessary and adequate line pressure for shift change is set.
For this reason, line pressure pattern setting corresponds to input
torque and gearshift selection. Also, line pressure characteristic is
set according to engine speed, during engine brake operation.
At Low Fluid Temperature
When the A/T fluid temperature drops below the prescribed tempera-
ture, in order to speed up the action of each friction element, the line
pressure is set higher than the normal line pressure characteristic.
Shift ControlUCS002CI
The clutch pressure control solenoid is controlled by the signals from the switches and sensors. Thus, the
clutch pressure is adjusted to be appropriate to the engine load state and vehicle driving state. It becomes
possible to finely control the clutch hydraulic pressure with high precision and a smoother shift change charac-
teristic is attained.
SHIFT CHANGE
The clutch is controlled with the optimum timing and oil pressure by the engine speed, engine torque informa-
tion, etc.
PCIA0010E
PCIA0 011 E
PCIA0012E

TROUBLE DIAGNOSIS
AT-43
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
TROUBLE DIAGNOSISPFP:00004
DTC Inspection Priority ChartUCS002C R
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
NOTE:
If DTC U1000 is displayed with other DTCs, first perform the trouble diagnosis for DTC U1000. Refer to
AT-1 03
.
Fail-SafeUCS002CS
The TCM has an electrical fail-safe mode. This mode makes it possible to operate even if there is a an error in
a main electronic control input/output signal circuit. In fail-safe mode the transmission is fixed in 2nd or 4th
(depending on the breakdown position), so the customer should feel “slipping” or “poor acceleration”. When
fail-safe mode is triggered, when the ignition switch is switched “ON”, the AT CHECK indicator lamp flashes for
about 8 seconds.
Even when the electronic circuits are normal, under special conditions (for example, when slamming on the
brake with the wheels spinning drastically and stopping the tire rotation), the transmission can go into fail-safe
mode. If this happens, switch “OFF” the ignition switch for 10 seconds, then switch it “ON” again to return to
the normal shift pattern. Also, the AT CHECK indicator lamp flashes for about 8 seconds once, then is cleared.
Therefore, the customer's vehicle has returned to normal, so handle according to the “diagnostics flow” (Refer
to AT-46, "
WORK FLOW" ).
FAI L-S AFE FUN CT ION
If any malfunction occurs in a sensor or solenoid, this function controls the A/T to mark driving possible.
Vehicle Speed Sensor

Signals are input from two systems - from vehicle speed sensor A/T (revolution sensor) installed on the
transmission and from combination meter so normal driving is possible even if there is a malfunction in
one of the systems. And if vehicle speed sensor A/T (revolution sensor) has unusual cases, 5th gear is
prohibited.
Accelerator Pedal Position Sensor

If there is a malfunction in one of the systems, the accelerator opening angle is controlled by ECM accord-
ing to a pre-determined accelerator angle to make driving possible. And if there are malfunctions in tow
systems, the engine speed is fixed by ECM to a pre-determined engine speed to make driving possible.
Throttle Position Sensor

If there is a malfunction in one of the systems, the accelerator opening angle is controlled by ECM accord-
ing to a pre-determined accelerator angle to make driving possible. And if there are malfunctions in tow
systems, the accelerator opening angle is controlled by the idle signal sent from the ECM which is based
on input indicating either idle condition or off-idle condition (pre-determined accelerator opening) in order
to make driving possible.
PNP Switch

In the unlikely event that a malfunction signal enters the TCM, the position indicator is switched “OFF”, the
starter relay is switched “OFF” (starter starting is disabled), the back-up lamp relay switched “OFF” (back-
up lamp is OFF) and the position is fixed to the “D” range to make driving possible.
Starter Relay

The starter relay is switched “OFF”. (Starter starting is disabled.)
Priority Detected items (DTC)
1 U1000 CAN communication line
2 Except above

AT-44
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
A/T Interlock

If there is an A/T interlock judgment malfunction, the transmission is fixed in 2nd gear to make driving pos-
sible.
NOTE:
When the vehicle is driven fixed in 2nd gear, a turbine revolution sensor malfunction is displayed,
but this is not a turbine revolution sensor malfunction.

When the coupling pattern below is detected, the fail-safe action corresponding to the pattern is per-
formed.
A/T INTERLOCK COUPLING PATTERN TABLE

: NG X: OK
A/T 1st Engine Braking

When there is an A/T first gear engine brake judgment malfunction, the low coast brake solenoid is
switched “OFF” to avoid the engine brake operation.
Line Pressure Solenoid

The solenoid is switched “OFF” and the line pressure is set to the maximum hydraulic pressure to make
driving possible.
Torque Converter Clutch Solenoid

The solenoid is switched “OFF” to release the lock-up.
Low Coast Brake Solenoid

When a (electrical or functional) malfunction occurs, in order to make driving possible, the engine brake is
not applied in 1st and 2nd gear.
Input Clutch Solenoid

If a (electrical or functional) malfunction occurs with the solenoid either “ON” or “OFF”, the transmission is
held in 4th gear to make driving possible.
Direct Clutch Solenoid

If a (electrical or functional) malfunction occurs with the solenoid either “ON” or “OFF”, the transmission is
held in 4th gear to make driving possible.
Front Brake Solenoid

If a (electrical or functional) malfunction occurs with the solenoid “ON”, in order to make driving possible,
the A/T is held in 5th gear; if the solenoid is OFF, 4th gear.
High and Low Reverse Clutch Solenoid

If a (electrical or functional) malfunction occurs with the solenoid either “ON” or “OFF”, the transmission is
held in 4th gear to make driving possible.
Turbine Revolution Sensor 1 or 2

The control is the same as if there were no turbine revolution sensors, 5th gear is prohibited.
Gear positionATF pressure switch output
Fail-safe
functionClutch pressure output pattern after fail-safe func-
tion
SW3
(I/C)SW6
(HLR/
C)SW5
(D/C)SW1
(Fr/B)SW2
(LC/B)I/C HLR/C D/C Fr/B LC/B L/U
A/T inter-
lock cou-
pling pattern3rd – X X –
Held in
2nd gearOFF OFF ON OFF OFF OFF
4th – X X –
Held in
2nd gearOFF OFF ON OFF OFF OFF
5th X X – X
Held in
2nd gearOFF OFF ON OFF OFF OFF

AT-48
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
4❏ Perform all road tests and enter checks in required inspection items.AT-6 1
4-1.Check before engine is started
AT-6 2
❏ AT-191, "AT CHECK Indicator Lamp Does Not Come On" .
❏ Perform self-diagnostics Enter checks for detected items. AT- 9 3
❏ AT- 1 0 3 , "DTC U1000 CAN COMMUNICATION LINE"
❏ AT- 1 0 5 , "DTC P0615 START SIGNAL CIRCUIT"
❏ AT- 1 0 8 , "DTC P0700 TCM"
❏ AT- 1 0 9 , "DTC P0705 PARK/NEUTRAL POSITION SWITCH"
❏ AT- 11 2 , "DTC P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)"
❏ AT- 11 5 , "DTC P0725 ENGINE SPEED SIGNAL"
❏ AT- 11 8 , "DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE"
❏ AT- 1 2 1 , "DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)"
❏ AT- 1 2 4 , "DTC P0745 LINE PRESSURE SOLENOID VALVE"
❏ AT- 1 2 7 , "DTC P1702 TRANSMISSION CONTROL MODULE (RAM)"
❏ AT- 1 2 8 , "DTC P1703 TRANSMISSION CONTROL MODULE (ROM)"
❏ AT- 1 2 9 , "DTC P1705 THROTTLE POSITION SENSOR"
❏ AT- 1 3 1 , "DTC P1710 A/T FLUID TEMPERATURE SENSOR CIRCUIT"
❏ AT- 1 3 4 , "DTC P1716 TURBINE REVOLUTION SENSOR"
❏ AT- 1 3 6 , "DTC P1721 VEHICLE SPEED SENSOR MTR"
❏ AT- 1 3 9 , "DTC P1730 A/T INTERLOCK"
❏ AT- 1 4 2 , "DTC P1731 A/T 1ST ENGINE BRAKING"
❏ AT- 1 4 5 , "DTC P1752 INPUT CLUTCH SOLENOID VALVE"
❏ AT- 1 4 8 , "DTC P1754 INPUT CLUTCH SOLENOID VALVE FUNCTION"
❏ AT- 1 5 1 , "DTC P1757 FRONT BRAKE SOLENOID VALVE"
❏ AT- 1 5 4 , "DTC P1759 FRONT BRAKE SOLENOID VALVE FUNCTION"
❏ AT- 1 5 7 , "DTC P1762 DIRECT CLUTCH SOLENOID VALVE"
❏ AT- 1 6 0 , "DTC P1764 DIRECT CLUTCH SOLENOID VALVE FUNCTION"
❏ AT- 1 6 3 , "DTC P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE"
❏ AT- 1 6 6 , "DTC P1769 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE
FUNCTION"
❏ AT- 1 6 9 , "DTC P1772 LOW COAST BRAKE SOLENOID VALVE"
❏ AT- 1 7 2 , "DTC P1774 LOW COAST BRAKE SOLENOID VALVE FUNCTION"
❏ AT- 1 7 5 , "DTC P1841 ATF PRESSURE SWITCH 1"
❏ AT- 1 7 8 , "DTC P1843 ATF PRESSURE SWITCH 3"
❏ AT- 1 8 1 , "DTC P1845 ATF PRESSURE SWITCH 5"
❏ AT- 1 8 4 , "DTC P1846 ATF PRESSURE SWITCH 6"
4-2.Idle inspection
AT-6 2
❏ AT-192, "Engine Cannot Be Started In “P” or “N” Position"
❏ AT-193, "In “P” Position, Vehicle Moves When Pushed"
❏ AT-194, "In “N” Position, Vehicle Moves"
❏ AT-195, "Large Shock (“N” to “D” Position)"
❏ AT-198, "Vehicle Does Not Creep Backward In “R” Position"
❏ AT-201, "Vehicle Does Not Creep Forward In “D” Position"
4-3.Driving tests
AT-6 3
Part 1
❏ AT-203, "
Vehicle Cannot Be Started From D1"
❏ AT-206, "A/T Does Not Shift: D1 → D2"
❏ AT-208, "A/T Does Not Shift: D2 → D3"
❏ AT-210, "A/T Does Not Shift: D3 → D4"
❏ AT-213, "A/T Does Not Shift: D4 → D5"
❏ AT-215, "A/T Does Not Perform Lock-up"
❏ AT-217, "A/T Does Not Hold Lock-up Condition"
❏ AT-219, "Lock-up Is Not Released"
❏ AT-220, "Engine Speed Does Not Return to Idle"

TROUBLE DIAGNOSIS
AT-49
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
44-3Part 2
AT- 6 5
❏ AT-203, "Vehicle Cannot Be Started From D1"
❏ AT-206, "A/T Does Not Shift: D1 → D2"
❏ AT-208, "A/T Does Not Shift: D2 → D3"
❏ AT-210, "A/T Does Not Shift: D3 → D4"
Part 3
AT- 6 6
❏ AT-221, "A/T Does Not Shift: 5th gear → 4th gear"
❏ AT-224, "A/T Does Not Shift: 4th gear → 3rd gear"
❏ AT-225, "A/T Does Not Shift: 3rd gear → 2nd gear"
❏ AT-227, "A/T Does Not Shift: 2nd gear → 1st gear"
❏ AT-230, "Vehicle Does Not Decelerate By Engine Brake"
❏ Perform self-diagnostics Enter checks for detected items. AT- 9 3
❏ AT-103, "DTC U1000 CAN COMMUNICATION LINE"
❏ AT-105, "DTC P0615 START SIGNAL CIRCUIT"
❏ AT-108, "DTC P0700 TCM"
❏ AT-109, "DTC P0705 PARK/NEUTRAL POSITION SWITCH"
❏ AT-112, "DTC P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)"
❏ AT-115, "DTC P0725 ENGINE SPEED SIGNAL"
❏ AT-118, "DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE"
❏ AT-121, "DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)"
❏ AT-124, "DTC P0745 LINE PRESSURE SOLENOID VALVE"
❏ AT-127, "DTC P1702 TRANSMISSION CONTROL MODULE (RAM)"
❏ AT-128, "DTC P1703 TRANSMISSION CONTROL MODULE (ROM)"
❏ AT-129, "DTC P1705 THROTTLE POSITION SENSOR"
❏ AT-131, "DTC P1710 A/T FLUID TEMPERATURE SENSOR CIRCUIT"
❏ AT-134, "DTC P1716 TURBINE REVOLUTION SENSOR"
❏ AT-136, "DTC P1721 VEHICLE SPEED SENSOR MTR"
❏ AT-139, "DTC P1730 A/T INTERLOCK"
❏ AT-142, "DTC P1731 A/T 1ST ENGINE BRAKING"
❏ AT-145, "DTC P1752 INPUT CLUTCH SOLENOID VALVE"
❏ AT-148, "DTC P1754 INPUT CLUTCH SOLENOID VALVE FUNCTION"
❏ AT-151, "DTC P1757 FRONT BRAKE SOLENOID VALVE"
❏ AT-154, "DTC P1759 FRONT BRAKE SOLENOID VALVE FUNCTION"
❏ AT-157, "DTC P1762 DIRECT CLUTCH SOLENOID VALVE"
❏ AT-160, "DTC P1764 DIRECT CLUTCH SOLENOID VALVE FUNCTION"
❏ AT-163, "DTC P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE"
❏ AT-166, "DTC P1769 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE
FUNCTION"
❏ AT-169, "DTC P1772 LOW COAST BRAKE SOLENOID VALVE"
❏ AT-172, "DTC P1774 LOW COAST BRAKE SOLENOID VALVE FUNCTION"
❏ AT-175, "DTC P1841 ATF PRESSURE SWITCH 1"
❏ AT-178, "DTC P1843 ATF PRESSURE SWITCH 3"
❏ AT-181, "DTC P1845 ATF PRESSURE SWITCH 5"
❏ AT-184, "DTC P1846 ATF PRESSURE SWITCH 6"
5❏ Inspect each system for items found to be NG in the self-diagnostics and repair or replace the malfunction
parts.
6❏ Perform all road tests and enter the checks again for the required items.AT- 6 1
7❏ For any remaining NG items, perform the “diagnostics procedure” and repair or replace the malfunction parts.
See the chart for diagnostics by symptoms. (This chart also contains other symptoms and inspection proce-
dures.)AT- 6 8
8❏ Erase the results of the self-diagnostics from the TCM.AT- 4 0

AT-68
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
Symptom ChartUCS002D6

The diagnostics item numbers show the sequence for inspection. Inspect in order from item 1.

Overhaul and inspect inside the A/T only if A/T fluid condition is NG. Refer to AT-58, "Fluid Condi-
tion Check" .
No. Items Symptom Condition Diagnostic ItemReference
page
1
Shift
ShockLarge shock. (“N” →“
D” position)
Refer to AT-195,
"Large Shock (“N” to
“D” Position)" .ON vehicle1. Engine idle speedEC-32
2. Engine speed signalAT - 11 5
3. Accelerator pedal position sensorAT- 1 2 9
4. Control cable adjustmentAT- 2 3 4
5. ATF temperature sensorAT- 1 3 1
6. ATF pressure switch 1 and front brake solenoid valveAT- 1 7 5,
AT- 1 5 1
7. CAN communication lineAT- 1 0 3
8. Fluid level and stateAT-5 8
9. Line pressure testAT-5 9
10. Control valve with TCMAT- 2 4 2
OFF vehicle11. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 8 , AT- 1 9
.)AT- 2 7 3
2Shock is too large
when changing D1 →
D
2 .ON vehicle1. Accelerator pedal position sensorAT- 1 2 9
2. Control cable adjustmentAT- 2 3 4
3. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 8 1,
AT- 1 5 7
4. CAN communication lineAT- 1 0 3
5. Engine speed signalAT - 11 5
6. Turbine revolution sensorAT- 1 3 4
7. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
8. Fluid level and stateAT-5 8
9. Control valve with TCMAT- 2 4 1
OFF vehicle 10. Direct clutchAT- 3 0 7
3Shock is too large
when changing D2 →
D
3 .ON vehicle1. Accelerator pedal position sensorAT- 1 2 9
2. Control cable adjustmentAT- 2 3 4
3. ATF pressure switch 6, high and low reverse clutch sole-
noid valveAT- 1 8 4,
AT- 1 6 3
4. CAN communication lineAT- 1 0 3
5. Engine speed signalAT - 11 5
6. Turbine revolution sensorAT- 1 3 4
7. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
8. Fluid level and stateAT-5 8
9. Control valve with TCMAT- 2 4 1
OFF vehicle 10. High and low reverse clutchAT- 3 0 5

TROUBLE DIAGNOSIS
AT-69
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
4
Shift
ShockShock is too large
when changing D3 →
D
4 .ON vehicle1. Accelerator pedal position sensorAT- 1 2 9
2. Control cable adjustmentAT- 2 3 4
3. ATF pressure switch 3 and input clutch solenoid valveAT- 1 7 8,
AT- 1 4 5
4. CAN communication lineAT- 1 0 3
5. Engine speed signalAT- 11 5
6. Turbine revolution sensorAT- 1 3 4
7. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
8. Fluid level and stateAT- 5 8
9. Control valve with TCMAT- 2 4 1
OFF vehicle 10. Input clutchAT- 2 9 5
5Shock is too large
when changing D4 →
D
5 .ON vehicle1. Accelerator pedal position sensorAT- 1 2 9
2. Control cable adjustmentAT- 2 3 4
3. ATF pressure switch 1 and front brake solenoid valveAT- 1 7 5,
AT- 1 5 1

4. CAN communication lineAT- 1 0 3
5. Engine speed signalAT- 11 5
6. Turbine revolution sensorAT- 1 3 4
7. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
8. Fluid level and stateAT- 5 8
9. Control valve with TCMAT- 2 4 1
OFF vehicle10. Front brake (brake band)AT- 2 6 111. Input clutchAT- 2 9 5
6Shock is too large for
downshift when accel-
erator pedal is
pressed.ON vehicle1. Accelerator pedal position sensorAT- 1 2 9
2. Control cable adjustmentAT- 2 3 4
3. CAN communication lineAT- 1 0 3
4. Engine speed signalAT- 11 5
5. Turbine revolution sensorAT- 1 3 4
6. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
7. Fluid level and stateAT- 5 8
8. Control valve with TCMAT- 2 4 1
OFF vehicle9. Front brake (brake band)AT- 2 6 110. Input clutchAT- 2 9 5
11. High and low reverse clutchAT- 3 0 5
12. Direct clutchAT- 3 0 7
No. Items Symptom Condition Diagnostic ItemReference
page

AT-70
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
7
Shift
ShockShock is too large for
upshift when acceler-
ator pedal is released.ON vehicle1. Accelerator pedal position sensorAT- 1 2 9
2. Control cable adjustmentAT- 2 3 4
3. Engine speed signalAT - 11 5
4. CAN communication lineAT- 1 0 3
5. Turbine revolution sensorAT- 1 3 4
6. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
7. Fluid level and stateAT-5 8
8. Control valve with TCMAT- 2 4 1
OFF vehicle9. Front brake (brake band)AT- 2 6 110. Input clutchAT- 2 9 5
11. High and low reverse clutchAT- 3 0 5
12. Direct clutchAT- 3 0 7
8Shock is too large for
lock-up.ON vehicle1. Accelerator pedal position sensorAT- 1 2 9
2. Control cable adjustmentAT- 2 3 4
3. Engine speed signalAT - 11 5
4. CAN communication lineAT- 1 0 3
5. Turbine revolution sensorAT- 1 3 4
6. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
7. Torque converter clutch solenoid valveAT - 11 8
8. Fluid level and stateAT-5 8
9. Control valve with TCMAT- 2 4 1
OFF vehicle 10. Torque converterAT- 2 7 3
9Shock is too large
during engine brake.ON vehicle1. Accelerator pedal position sensorAT- 1 2 9
2. Control cable adjustmentAT- 2 3 4
3. CAN communication lineAT- 1 0 3
4. Fluid level and stateAT-5 8
5. Control valve with TCMAT- 2 4 1
OFF vehicle6. Front brake (brake band)AT- 2 6 17. Input clutchAT- 2 9 5
8. High and low reverse clutchAT- 3 0 5
9. Direct clutchAT- 3 0 7
No. Items Symptom Condition Diagnostic ItemReference
page