2004 INFINITI FX35 ground

POWER WINDOW SYSTEM
GW-37
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2004 November 2004 FX35/FX45
Terminal and Reference Value for BCM / With Front and Rear Power Window
Anti-pinch
AIS004Q7
Terminal Wire color Item ConditionVoltage [V]
(Approx.)
12 P/BFront door switch
passenger side signalON (Open) 0
OFF (Close) Battery voltage
22 OR Power window serial linkIGN SW ON or power window
timer operating.
38 W/L Ignition switch (ON or START) Ignition switch
(ON or START position)Battery voltage
39 L CAN - H — 0
40 R CAN - L — 0
42 L/R Battery power supply — Battery voltage
49 B Ground (signal) — 0
52 B Ground (power) — 0
53 Y/B Rap signalIGN SW ON Battery voltage
Within 45 second after ignition
switch is turned to OFFBattery voltage
When driver side or passenger
side door is open in power win-
dow timer is operates0
54 W Power window power supply — Battery voltage
55 G Battery power supply — Battery voltage
62 WFront door switch
driver side signalON (Open) 0
OFF (Close) Battery voltage
PIIA2344J

GW-38
POWER WINDOW SYSTEM
Revision: 2004 November 2004 FX35/FX45
Terminal and Reference Value for Power Window Main Switch / With Front and
Rear Power Window Anti-pinch System
AIS004Q8
Terminal Wire color Item ConditionVoltage [V]
(Approx.)
2 SB Limit switch and encoder ground — 0
4PDoor key cylinder switch
LOCK signalKey position
(Neutral → Locked)5 → 0
6ORDoor key cylinder switch
UNLOCK signalKey position
(Neutral → Unlocked)5 → 0
8LFront driver side power window
motor UP signalWhen front LH switch in
power window main switch is
UP at operated. Battery voltage
9 GY Limit switch signalDriver side door window is between
fully-open and just before fully-
closed position (ON).0
Driver side door window is between
just before fully-closed position and
fully-closed position (OFF).5
10 BR Rap signalIGN SW ON Battery voltage
Within 45 second after ignition
switch is turned to OFFBattery voltage
When driver side or passenger side
door is open in power window timer
is operates0
11 BFront driver side power window
motor DOWN signalWhen front LH switch in
power window main switch is
DOWN at operated. Battery voltage
13 PU Encoder pulse signalWhen power window motor oper-
ates.
14 Y Power window serial linkIGN SW ON or power window timer
operating.
15 W Encoder power supplyWhen ignition switch ON or power
window timer operates.10
17 B Ground — 0
19 W Battery power supply — Battery voltage
OCC3383D
PIIA2344J

POWER WINDOW SYSTEM
GW-39
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2004 November 2004 FX35/FX45
Terminal and Reference Value for (Front and Rear) Power Window Switch / With
Front and Rear Window Anti-pinch System
AIS004Q9
( ): Rear power window switch (LH or RH)
Work FlowAIS004QA
1. Check the symptom and customer's requests.
2. Understand the outline of system. Refer to GW-16, "
System Description"
3. According to the trouble diagnosis chart, repair or replace the cause of the malfunction.
Refer to GW-42, "
Trouble Diagnosis Symptom Chart / With Front Power Window Anti-pinch System" or
GW-43, "
Trouble Diagnosis Symptom Chart / With Front and Rear Power Window Anti-pinch System"
4. Does power window system operate normally? Yes, GO TO 5, If No, GO TO 3.
5. INSPECTION END
Terminal Wire color Item ConditionVoltage [V]
(Approx.)
3SB
(OR)Limit switch and encoder ground — 0
4R
(PU)Encoder power supplyWhen ignition switch ON or power
window timer operates10
8LPower window motor
UP signalWhen power window motor is
UP at operated. Battery voltage
9GPower window motor
DOWN signalWhen power window motor is
DOWN at operated.Battery voltage
10 W Battery power supply — Battery voltage
11 B G r o u n d — 0
12PU
(G/Y)Encoder pulse signalWhen power window motor oper-
ates.
15GY
(R)Limit switch signalDoor window is between fully-open
and just before fully-closed position
(ON)0
Door window is between just before
fully-closed position and fully-closed
position (OFF)5
16 Y Power window serial linkIGN SW ON or power window timer
operating.
OCC3383D
PIIA2344J

GW-42
POWER WINDOW SYSTEM
Revision: 2004 November 2004 FX35/FX45
Trouble Diagnosis Symptom Chart / With Front Power Window Anti-pinch Sys-
tem
AIS004QC

Make sure other systems using the signal of the following systems operate normally.
Symptom Repair order Refer to page
None of the power windows can be operated using any switch.1. BCM power supply and ground circuit checkGW-44
2. Power window main switch power supply
and ground circuit checkGW-45
3. Power window serial link checkGW-71
Driver side power window alone does not operated.1. Front power window motor (driver side) cir-
cuit checkGW-48
2. Replace power window main switch —
Front passenger side power window alone does not operated.1. Front power window switch (passenger side)
power and ground circuit checkGW-46
2. Power window serial link checkGW-71
3. Front power window motor (passenger side)
circuit checkGW-49
4. Replace BCMBCS-15
Rear LH side power window alone does not operated 1. Rear power window motor (LH) circuit checkGW-50
Rear RH side power window alone does not operated 1. Rear power window motor (RH) circuit checkGW-52
Anti-pinch system does not operate normally (driver side)1. Door window sliding part malfunction

A foreign material adheres to window glass
or glass run rubber.

Glass run rubber wear or deformation.

Sash is tilted too much, or no enough.—
2. Limit switch adjustingGW-78
3. Limit switch circuit check (driver side)GW-56
4. Encoder circuit check (driver side)GW-61
Anti-pinch system does not operate normally (passenger side)1. Door window sliding part malfunction

A foreign material adheres to window glass
or glass run rubber.

Glass run rubber wear or deformation.

Sash is tilted too much, or no enough.—
2. Limit switch adjustingGW-78
3. Limit switch circuit check (passenger side)GW-57
4. Encoder circuit check (passenger side)GW-63
Power window retained power operation does not operate properly1. Check the retained power operation mode
setting.GW-412. Door switch checkGW-67
3. Replace BCM.BCS-15
Does not operate by key cylinder switch1. Door key cylinder switch checkGW-692. Replace power window main switch —
Power window lock switch does not function 1. Power window lock switch checkGW-73
Auto operation does not operate but manual operates normally
(driver side)1. Encoder circuit check (driver side)GW-61
2. Replace power window main switch. —
Auto operation does not operate but manual operates normally
(passenger side)1. Encoder circuit check (passenger side)GW-63
2. Replace front power window switch (passen-
ger side)—

POWER WINDOW SYSTEM
GW-43
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2004 November 2004 FX35/FX45
Trouble Diagnosis Symptom Chart / With Front and Rear Power Window Anti-
pinch System
AIS004QD

Make sure other systems using the signal of the following systems operate normally.
Symptom Repair order Refer to page
None of the power windows can be operated using any switch.1. BCM power supply and ground circuit checkGW-44
2. Power window main switch power supply and
ground circuit checkGW-45
3. Power window serial link checkGW-71
Driver side power window alone does not operated.1. Front power window motor (driver side) circuit
checkGW-48
2. Replace power window main switch —
Front passenger side power window alone does not operated.1. Front power window switch (passenger side)
power and ground circuit checkGW-46
2. Power window serial link checkGW-71
3. Front power window motor (passenger side)
circuit checkGW-49
4. Replace BCMBCS-15
Rear LH or RH side power window alone does not operated1. Rear power window switch (LH or RH)
power and ground circuit checkGW-472. Power window serial link checkGW-73
3. Rear power window motor (LH or RH) circuit
checkGW-55
4. Replace rear power window switch (LH or RH)EI-35
Anti-pinch system does not operate normally (driver side)1. Door window sliding part malfunction

A foreign material adheres to window glass or
glass run rubber.

Glass run rubber wear or deformation.

Sash is tilted too much, or no enough.—
2. Limit switch adjustingGW-78
3. Limit switch circuit check (driver side)GW-56
4. Encoder circuit check (driver side)GW-61
Anti-pinch system does not operate normally (passenger side)1. Door window sliding part malfunction

A foreign material adheres to window glass or
glass run rubber.

Glass run rubber wear or deformation.

Sash is tilted too much, or no enough.—
2. Limit switch adjustingGW-78
3. Limit switch circuit check (passenger side)GW-57
4. Encoder circuit check (passenger side)GW-63
Anti-pinch system does not operate normally (rear LH or RH)1. Door window sliding part malfunction

A foreign material adheres to window glass or
glass run rubber.

Glass run rubber wear or deformation.

Sash is tilted too much, or no enough.—
2. Limit switch adjustingGW-78
3. Limit switch circuit check (rear LH or RH)GW-59
4. Encoder circuit check (rear LH or RH)GW-65

GW-44
POWER WINDOW SYSTEM
Revision: 2004 November 2004 FX35/FX45
BCM Power Supply and Ground Circuit CheckAIS004QE
1. CHECK FUSE

Check 15A fuse [No.1, located in fuse block (J/B)]

Check 15A fuse [No.22, located in fuse block (J/B)]

Check 50A fusible link (letter M located in the fuse and fusible link box).
NOTE:
Refer to GW-15, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown out, be sure to eliminate cause of malfunction before installing new fuse. Refer to
PG-3, "
POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between BCM connector M3, M4 terminal 38, 42,
55 and ground.
OK or NG
OK >> GO TO 3.
NG >> Check BCM power supply circuit for open or short.
Power window retained power operation does not operate
properly1. Check the retained power operation mode set-
ting.GW-41
2. Door switch checkGW-67
3. Replace BCM.BCS-15
Does not operate by key cylinder switch1. Door key cylinder switch checkGW-692. Replace power window main switch —
Power window lock switch does not function 1. Power window lock switch checkGW-73
Auto operation does not operate but manual operate normally
(driver side)1. Encoder circuit check (driver side)GW-61
2. Replace power window main switch —
Auto operation does not operate but manual operate normally
(passenger side)1. Encoder circuit check (passenger side)GW-63
2. Replace front power window switch (passen-
ger side)—
Auto operation does not operate but manual operate normally
(rear LH or RH)1. Encoder circuit check (rear LH or RH)GW-65
2. Replace rear power window switch (LH or RH) — Symptom Repair order Refer to page
38 (W/L) – Ground : Battery voltage
42 (L/R) – Ground : Battery voltage
55 (G) – Ground : Battery voltage
PIIA6160E

POWER WINDOW SYSTEM
GW-45
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2004 November 2004 FX35/FX45
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM connector M4 terminal 49, 52
and ground.
OK or NG
OK >> Power supply and ground circuit are OK.
NG >> Check BCM ground circuit for open or short.
Power Window Main Switch Power Supply Circuit Check AIS004QF
1. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between power window main switch connector
D6, D7 terminal 10, 19 and ground.
OK or NG
OK >> Power window main switch power supply and ground
circuit are OK.
NG >> GO TO 2.
2. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect power window main switch connector.
3. Check continuity between power window main switch connector
D7 terminal 17 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.49 (B) – Ground : Continuity should exist.
52 (B) – Ground : Continuity should exist.
PIIA6161E
10 (BR) – Ground : Battery voltage
19 (W) – Ground : Battery voltage
PIIA4171E
17 (B) – Ground : Continuity should exist.
PIIA4172E

GW-46
POWER WINDOW SYSTEM
Revision: 2004 November 2004 FX35/FX45
3. CHECK HARNESS CONTINUITY
1. Disconnect BCM connector.
2. Check continuity between BCM connector M4 terminal 53, 54
and power window main switch connector D6, D7 terminal 10,
19.
3. Check continuity between BCM connector M4 terminal 53, 54
and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness.
4. CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Turn ignition switch ON.
3. Check voltage between BCM connector M4 terminal 53, 54 and
ground.
OK or NG
OK >> Check condition of harness and connector.
NG >> Replace BCM.
Front Power Window Switch (Passenger Side) Power Supply and Ground Cir-
cuit Check
AIS004QG
1. CHECK POWER SUPPLY CIRCUIT
Check voltage between front power window switch (passenger side)
connector D36 terminal 10 and ground.
OK or NG
OK >> Front power window switch (passenger side) power sup-
ply and ground circuit are OK.
NG >> GO TO 2.53 (Y/B) – 10 (BR) : Continuity should exist.
54 (W) – 19 (W) : Continuity should exist.
53 (Y/B) – Ground : Continuity should not exist.
54 (W) – Ground : Continuity should not exist.
PIIA6280E
53 (Y/B) – Ground : Battery voltage
54 (W) – Ground : Battery voltage
PIIA6154E
10 (W) – Ground : Battery voltage
PIIA4174E