2004 INFINITI FX35 Power supply

TROUBLE DIAGNOSIS FOR SYMPTOMS
TF-33
C
E
F
G
H
I
J
K
L
MA
B
TF
Revision: 2004 November 2004 FX35/FX45
2. CHECK AWD CONTROL UNIT POWER SUPPLY CIRCUIT
1. Turn ignition switch “OFF”.
2. Disconnect AWD control unit harness connector.
3. Turn ignition switch “ON”. (Do not start engine.)
4. Check voltage between AWD control unit harness connector ter-
minals and ground.
5. Turn ignition switch “OFF”.
6. Check voltage between AWD control unit harness connector ter-
minals and ground.
OK or NG
OK >> GO TO 3.
NG >> Check the following. If any items are damaged, repair or
replace damaged parts.

10A fuse [No. 12 or 21, located in the fuse block (J/B)]

Harness for short or open between battery and AWD control unit harness connector terminal 9

Harness for short or open between ignition switch and AWD control unit harness connector ter-
minal 7

Ignition switch. Refer to PG-3, "POWER SUPPLY ROUTING CIRCUIT" .
3. CHECK AWD CONTROL UNIT GROUND CIRCUIT
1. Turn ignition switch “OFF”.
2. Disconnect AWD control unit harness connector.
3. Check continuity between AWD control unit harness connector
M92 terminals 10 (B), 11 (B) and ground.
Also check harness for short to ground and short to power.
OK or NG
OK >> GO TO 4.
NG >> Repair open circuit or short to ground or short to power
in harness or connectors.
Connector Terminal (Wire color) Voltage (Approx.)
M927 (G/R) - Ground
Battery voltage
9 (G/W) - Ground
SDIA2319E
Connector Terminal (Wire color) Voltage (Approx.)
M927 (G/R) - Ground 0V
9 (G/W) - Ground Battery voltage
SDIA2320E
Continuity should exist.
SDIA1883E

WT-14
TROUBLE DIAGNOSES
Revision: 2004 November 2004 FX35/FX45
Control Unit Input/Output Signal StandardAES000NU
Standards using a circuit tester and oscilloscope.
( ): Wire color
ID Registration ProcedureAES000NV
ID REGISTRATION WITH TRANSMITTER ACTIVATION TOOL
This procedure must do after replace transmitter or low tire pressure warning control unit.
1. Turn ignition switch “OFF”.
2. Connect CONSULT-II and CONSULT-II CONVERTER to data link connector.
3. Touch “AIR PRESSURE MONITOR”, “WORK SUPPORT” and “ID REGIST”.
NOTE:
If “AIR PRESSURE MONITOR” is not indicated, go to GI-40, "
CONSULT-II Data Link Connector (DLC)
Circuit" .
4. With the transmitter activation tool (J-45295) pushed against the
front-left transmitter position of the tire air valve, press the button
then keep 5 seconds.
5. Register the IDs in order from FR LH, FR RH, RR RH or RR LH. When ID registration of each wheel has
been completed, a buzzer sounds and hazard warning lamp blinks.
6. After completing all ID registrations, press “END” to complete the procedure.
NOTE:
Be sure to register the IDs in order from FR LH, FR RH, RR RH, to RR LH, or the self-diagnostic results dis-
play will not function properly.
Measurement terminal
Item Operation or condition
+–
8 (G)
GroundTire pressure warning check
switchAlways Approx. 5 V
9 (L) Data line (CAN H) — —
11 (LG/R) Ignition switch ACC — Battery voltage (Approx. 12 V)
12 (R/W) Battery power supply Always Battery voltage (Approx. 12 V)
20 (B) GND — Approx. 0 V
21 (R) Data line (CAN L) — —
22 (G/Y) HazardHazard lamp switch OFF Battery voltage (Approx. 12 V)
Hazard lamp switch ON Approx. 0 V
24 (G/R) Ignition switch ON — Battery voltage (Approx. 12 V)
25 Antenna — —
SEIA0460E
Activation tire position Buzzer Hazard warning lamp CONSULT-II
Front LH Once
2 times flashing“YET”
↓
“DONE” Front RH 2 times
Rear RH 3 times
Rear LH 4 times

WT-24
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: 2004 November 2004 FX35/FX45
Inspection 4: Vehicle Speed SignalAES000O4
MALFUNCTION CODE NO. 52
1. SELF-DIAGNOSIS RESULT CHECK
1. Connect CONSULT-II and CONSULT-II CONVERTER to data link connector.
NOTE:
If “AIR PRESSURE MONITOR” is not indicated, go to GI-40, "
CONSULT-II Data Link Connector (DLC)
Circuit" .
2. Select “AIR PRESSURE MONITOR” on “SELECT SYSTEM” screen.
3. Select “SELF-DIAG RESULTS” on “SELECT DIAG MODE” screen.
4. Check display contents in self-diagnostic results.
Is
“CAN COMM CIRCUIT” displayed in the self-diagnosis display items?
YES >> Malfunction in CAN communication system. GO TO LAN-4, "Precautions When Using CONSULT-
II" .
NO >> GO TO 2.
2. CHECK UNIFIED METER AND A/C AMP. POWER SUPPLY CIRCUIT
1. Disconnect unified meter and A/C amp. connector M56.
2. Check voltage between unified meter and A/C amp. harness connector M56 terminals 21 (R/W), 22 (G/R)
and ground.
OK or NG
OK >> GO TO 3.
NG >> Check unified meter and A/C amp. power supply circuit
for open or short.
3. CHECK UNIFIED METER AND A/C AMP. GROUND CIRCUIT

Check continuity between unified meter and A/C amp. harness connector M56 terminals 29 (B), 30 (B)
and ground.
OK or NG
OK >> Check unified meter and A/C amp. self-diagnostic. Refer
to DI-32, "
SELF-DIAGNOSTIC RESULTS" .
NG >> Repair or replace unified meter and A/C amp. ground circuit.Te r m i n a l s
Vo l ta g e
(Approx.)
(+) (–)
ConnectorTe r m i n a l
(Wire color)
Ground 12 V
M5621 (R/W)
22 (G/R)
SEIA0337E
Te r m i n a l s
Continuity
(+) (–)
ConnectorTe r m i n a l
(Wire color)
Ground Yes
M5629 (B)
30 (B)
SEIA0338E

TROUBLE DIAGNOSIS FOR SYMPTOMS
WT-25
C
D
F
G
H
I
J
K
L
MA
B
WT
Revision: 2004 November 2004 FX35/FX45
TROUBLE DIAGNOSIS FOR SYMPTOMSPFP:00007
Inspection 1: Warning Lamp Does Not Come On When Ignition Switch Is Turned
On.
AES000O5
DIAGNOSTIC PROCEDURE
1. SELF-DIAGNOSTIC RESULT CHECK
1. Connect CONSULT-II and CONSULT-II CONVERTER to data link connector.
NOTE:
If “AIR PRESSURE MONITOR” is not indicated, go to GI-40, "
CONSULT-II Data Link Connector (DLC)
Circuit"
2. Select “AIR PRESSURE MONITOR” on “SELECT SYSTEM” screen.
3. Select “SELF-DIAG RESULTS” on “SELECT DIAG MODE” screen.
4. Check display contents in self-diagnostic results.
Is
“CAN COMM CIRCUIT” displayed in the self-diagnosis display items?
YES >> Malfunction in CAN communication system. GO TO LAN-4, "Precautions When Using CONSULT-
II" .
NO >> GO TO 2.
2. CHECK COMBINATION METER

Check combination meter operation.
OK or NG
OK >> GO TO 3.
NG >> Check combination meter. Refer to DI-4, "
System Description" .
3. CHECK WARNING LAMP

Disconnect low tire pressure warning control unit connector.
Does the warning lamp activate?
YES >> Replace low tire pressure warning control unit.
NO >> GO TO 4.
4. CHECK UNIFIED METER AND A/C AMP. POWER SUPPLY CIRCUIT
1. Disconnect unified meter and A/C amp. connector M56.
2. Check voltage between unified meter and A/C amp. harness connector M56 terminals 21 (R/W), 22 (G/R)
and ground.
OK or NG
OK >> GO TO 5.
NG >> Check unified meter and A/C amp. power supply circuit
for open or short.Te r m i n a l s
Vo l ta g e
(Approx.)
(+) (–)
ConnectorTe r m i n a l
(Wire color)
Ground 12 V
M5621 (R/W)
22 (G/R)SEIA0337E

WT-26
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2004 November 2004 FX35/FX45
5. CHECK UNIFIED METER AND A/C AMP. GROUND CIRCUIT

Check continuity between unified meter and A/C amp. connector M56 terminals 29 (B), 30 (B) and
ground.
OK or NG
OK >> Check unified meter and A/C amp. Refer to DI-28, "Sys-
tem Description" .
NG >> Repair or replace unified meter and A/C amp. ground circuit.
Inspection 2: Warning Lamp Stays On When Ignition Switch Is Turned On.AES000O6
DIAGNOSTIC PROCEDURE
1. CHECK CONNECTOR
1. Disconnect low tire pressure warning control unit connectors M74.
2. Check terminals for damage or loose connections.
OK or NG
OK >> GO TO 2.
NG >> Repair or replace damaged parts.
2. CHECK POWER SUPPLY CIRCUIT 1
Check voltage between low tire pressure warning control unit connector M74 terminal 12 (R/W) and ground.
OK or NG
OK >> GO TO 3.
NG >> Check low tire pressure warning control unit power sup-
ply circuit for open or short.Te r m i n a l s
Continuity
(+) (–)
ConnectorTe r m i n a l
(Wire color)
Ground Yes
M5629 (B)
30 (B)
SEIA0338E
Te r m i n a l s
Vo l ta g e
(Approx.)
(+) (–)
ConnectorTe r m i n a l
(Wire color)
Ground 12 V
M74 12 (R/W)
SEIA0341E

TROUBLE DIAGNOSIS FOR SYMPTOMS
WT-27
C
D
F
G
H
I
J
K
L
MA
B
WT
Revision: 2004 November 2004 FX35/FX45
3. CHECK POWER SUPPLY CIRCUIT 2
1. Turn ignition switch ON.
2. Check voltage between low tire pressure warning control unit connector M74 terminals 11 (LG/R), 24 (G/
R) and ground.
OK or NG
OK >> GO TO 4.
NG >> Check low tire pressure warning control unit power sup-
ply circuit for open or short.
4. CHECK GROUND CIRCUIT

Check continuity between low tire pressure warning control unit connector M74 terminal 20(B) and
ground.
OK or NG
OK >> Replace low tire pressure warning control unit.
NG >> Repair or replace low tire pressure warning control unit
ground circuit.Te r m i n a l s
Vo l ta g e
(Approx.)
(+) (–)
ConnectorTe r m i n a l
(Wire color)
Ground 12 V
M7411 ( LG /R )
24 (G/R)
SEIA0342E
Te r m i n a l s
Continuity
(+) (–)
ConnectorTe r m i n a l
(Wire color)
Ground Yes
M74 20 (B)
SEIA0343E

WW-1
WIPER, WASHER & HORN
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION WW
A
B
WW
Revision: 2004 November 2004 FX35/FX45
WIPER, WASHER & HORN
PRECAUTION ............................................................ 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Wiring Diagrams and Trouble Diagnosis .................. 3
FRONT WIPER AND WASHER SYSTEM .................. 4
Components Parts and Harness Connector Loca-
tion ........................................................................... 4
System Description .................................................. 4
LOW SPEED WIPER OPERATION ...................... 5
HI SPEED WIPER OPERATION ........................... 5
INTERMITTENT OPERATION .............................. 5
AUTO STOP OPERATION .................................... 6
WASHER OPERATION ......................................... 6
MIST OPERATION ................................................ 6
FAIL-SAFE FUNCTION ......................................... 7
COMBINATION SWITCH READING FUNCTION ..... 7
CAN Communication System Description ................ 9
CAN Communication Unit ........................................ 9
Schematic .............................................................. 10
Wiring Diagram — WIPER — ................................. 11
Terminals and Reference Values for BCM ............. 14
Terminals and Reference Values for IPDM E/R ..... 15
How to Proceed With Trouble Diagnosis ................ 15
Preliminary Check .................................................. 16
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................... 16
CONSULT-II Functions (BCM) ............................... 17
CONSULT-II OPERATION .................................. 17
DATA MONITOR ................................................. 18
ACTIVE TEST ..................................................... 19
CONSULT-II Functions (IPDM E/R) ....................... 19
CONSULT-II OPERATION .................................. 19
SELF-DIAGNOSTIC RESULTS .......................... 20
DATA MONITOR ................................................. 20
ACTIVE TEST ..................................................... 21
Front Wiper Does Not Operate .............................. 21
Front Wiper Does Not Return to Stop Position ....... 24
Only Front Wiper LO Does Not Operate ................ 24Only Front Wiper HI Does Not Operate .................. 25
Only Front Wiper INT Does Not Operate ................ 25
Front Wiper Interval Time Is Not Controlled by Vehi-
cle Speed ................................................................ 26
Front Wiper Intermittent Operation Switch Position
Cannot Be Adjusted ................................................ 26
Wipers Do Not Wipe When Front Washer Operates ... 26
After Front Wipers Operate for 10 Seconds, They
Stop for 20 Seconds, and after repeating the oper-
ations five times, they become inoperative ............. 27
Front Wipers Do Not Stop ....................................... 28
Removal and Installation of Front Wiper Arms,
Adjustment of Wiper Arms Stop Location ............... 28
REMOVAL ........................................................... 28
INSTALLATION ................................................... 28
ADJUSTMENT .................................................... 29
Removal and Installation of Front Wiper Motor and
Linkage ................................................................... 29
REMOVAL ........................................................... 29
INSTALLATION ................................................... 29
Disassembly and Assembly of Front Wiper Motor
and Linkage ............................................................ 30
DISASSEMBLY ................................................... 30
ASSEMBLY ......................................................... 30
Washer Nozzle Adjustment .................................... 30
Washer Tube Layout .............................................. 32
Removal and Installation of Front Washer Nozzle ... 32
Removal and Installation of Front Washer Tube
Joint ........................................................................ 32
REMOVAL ........................................................... 32
INSTALLATION ................................................... 32
Check Valve Inspection .......................................... 32
Removal and Installation of Front Wiper and Washer
Switch ..................................................................... 33
REMOVAL ........................................................... 33
INSTALLATION ................................................... 33
Removal and Installation of Washer Tank .............. 33
REMOVAL ........................................................... 33

WW-2Revision: 2004 November 2004 FX35/FX45INSTALLATION .................................................... 34
Removal and Installation of Washer Motor ............. 34
REMOVAL ........................................................... 34
INSTALLATION .................................................... 34
REAR WIPER AND WASHER SYSTEM .................. 35
Component Parts and Harness Connector Location ... 35
System Description ................................................. 35
REAR WIPER OPERATION ................................ 35
INTERMITTENT OPERATION ............................ 36
AUTO STOP OPERATION .................................. 36
WASHER OPERATION ....................................... 36
BCM WIPER SWITCH READING FUNCTION .... 36
Wiring Diagram — WIP/ R — ................................. 37
Terminals and Reference Values for BCM .............. 39
How to Proceed With Trouble Diagnosis ................ 40
Preliminary Check .................................................. 40
INSPECTION POWER SUPPLY AND GROUND
CIRCUIT .............................................................. 40
CONSULT-II Functions ........................................... 41
CONSULT-II OPERATION ................................... 41
DATA MONITOR .................................................. 42
ACTIVE TEST ..................................................... 43
Rear Wiper Does Not Operate ............................... 43
Rear Wiper Does Not Return to Stop Position ........ 45
Only Rear Wiper ON Does Not Operate ................. 46
Only Rear Wiper INT Does Not Operate ................ 46
Wiper Does Not Wipe When Rear Washer Operates ... 46
Rear Wipers Do Not Stop ....................................... 46
Removal and Installation of Rear Wiper Arm, Adjust-
ment of Wiper Arms Stop Location ......................... 48
REMOVAL ........................................................... 48
INSTALLATION .................................................... 48
Removal and Installation of Rear Wiper Motor ....... 48
REMOVAL ........................................................... 49
INSTALLATION .................................................... 49
Removal and Installation of Rear Wiper Blade ....... 49REMOVAL ............................................................ 49
INSTALLATION .................................................... 49
Washer Nozzle Adjustment ..................................... 49
Removal and Installation of Washer Nozzle ........... 50
REMOVAL ............................................................ 50
INSTALLATION .................................................... 50
Washer Tube Layout ............................................... 50
Check Valve Inspection ........................................... 51
Removal and Installation of Rear Wiper and Washer
Switch ..................................................................... 51
Removal and Installation of Washer Tank ............... 51
Removal and Installation of Washer Pump ............. 51
CIGARETTE LIGHTER ............................................. 52
Wiring Diagram — CIGAR — .................................. 52
Removal and Installation of Cigarette Lighter ......... 53
REMOVAL ............................................................ 53
INSTALLATION .................................................... 53
POWER SOCKET ..................................................... 54
Wiring Diagram — P/SCKT — ................................ 54
Removal and Installation of Center Console Box
Rear Side Power Socket ......................................... 55
REMOVAL ............................................................ 55
INSTALLATION .................................................... 55
Removal and Installation of Center Console Box
Power Socket .......................................................... 55
REMOVAL ............................................................ 55
INSTALLATION .................................................... 55
Removal and Installation of Luggage Room Power
Socket ..................................................................... 55
REMOVAL ............................................................ 55
INSTALLATION .................................................... 55
HORN ........................................................................ 56
Wiring Diagram — HORN — .................................. 56
Removal and Installation ......................................... 57
REMOVAL ............................................................ 57
INSTALLATION .................................................... 57