2004 INFINITI FX35 Engine

LASER BEAM AIMING ADJUSTMENT
ACS-15
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
3. Start the engine, wait for at least 10 sec., and touch “START
(NISSAN BASED VHCL)”.
4. Touch “ICC”.
If “ICC” is not indicated, go to GI-40, "
CONSULT-II Data Link
Connector (DLC) Circuit" .
5. Touch “WORK SUPPORT”.
6. Touch “LASER BEAM ADJUST”.
7. Touch “START”.
CAUTION:
If the adjustment screen does not appear on CONSULT-II 10
sec. after touching “LASER BEAM ADJUST” screen, the fol-
lowing causes may be considered:

Target is not set accurately.

There is not enough space beside the target.

Deformation of vehicle or the surrounding equipment
unit, bracket, or the surrounding equipment is causing
inappropriate installation of sensor and aiming may be
set out of the adjustable range.
SKIA3098E
SKIA6193E
PKIA8867E
SKIA6191E
SKIA1220E

ACS-32
[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
Revision: 2004 November 2004 FX35/FX45
DATA MONITOR
Operation Procedure
1. Touch “DATA MONITOR” on the selection screenACS-30,
"CONSULT-II INSPECTION PROCEDURE" .
2. Touch any of “ECU INPUT SIGNALS”, “MAIN SIGNALS”, and
“SELECTION FROM MENU” on selection screen.
3. Touch “SETTING”.
4. Display the data monitor.
5. If necessary, touch “COPY” in turn, and print data.
Monitored Item
×: Applicable
PKIA8868E
Monitored Item [unit]MAIN SIG-
NALSECU
INPUT
SIGNALSSELEC-
TION
FROM
MENUDescription
VHCL SPEED SE
[km/h] or [mph]×××Indicates vehicle speed calculated from wheel speed sen-
sor signal.
SET VHCL SPD
[km/h] or [mph]××Indicates set vehicle speed memorized in ICC unit.
THRTL OPENING
[%]×××Indicates throttle angle calculated from signal voltage of
throttle position sensor.
ENGINE RPM
[rpm]××Indicates engine speed read by ICC unit via CAN commu-
nication (ECM transmits engine speed via CAN communi-
cation).
DISTANCE ADJ
[SHOR/MID/LONG]×××Indicates set distance memorized in ICC unit.
WIPER SW
[OFF/LOW/HIGH]××Indicates wiper [OFF/LOW/HIGH] status.
MAIN SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from control switch
signal.
SET/COAST SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from control switch
signal.
CANCEL SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from control switch
signal.
RESUME/ACC SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from control switch
signal.
CRUISE OPE
[ON/OFF]××Indicates whether controlling or not (ON means “control-
ling”).
BRAKE SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from ICC brake
switch signal.
STOP LAMP SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from stop lamp
switch signal.
RELEASE SW NO
[ON/OFF]
××Indicates [ON/OFF] status as judged from release switch
signal.
ON when brake is depressed.
OFF when brake is not depressed.
RELEASE SW NC
[ON/OFF]
××Indicates [ON/OFF] status as judged from release switch
signal.
OFF when brake is depressed.
ON when brake is not depressed.

TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
ACS-35
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
METER LAMP

Start engine.

Touch “ON” and “OFF” to check that ICC system display oper-
ates as in the following chart.
STOP LAMP

Touch “ON” and “OFF” to check that stop lamp operates as in
the following chart.
BOOSTER SOL/V 3

Touch any of “MODE 1”, “MODE 2”, “MODE 3” to check that fol-
lowing operation condition is caused by operating monitor and
brake pedal.

“START” is displayed 10 seconds after operation start. (Active
test is completed.)
Self-Diagnostic FunctionAKS006YV
WITH CONSULT-II
1. Go to operation check after asking the customer for symptom information. Refer to ACS-9, "ACTION
TEST" .
2. Stop vehicle, turn ignition switch OFF, then connect CONSULT-II and CONSULT-II CONVERTER to data
link connector.
3. With engine started, touch “START”, “ICC”, “SELF-DIAG RESULTS” on CONSULT-II screen in this order.
METER LAMP ON OFF
ICC system display Full illumination OFF
SKIA1231E
STP LMP DRIVE ON OFF
Stop lamp Lamp ON Lamp OFF
SKIA1232E
SKIA1233E
PKIA0363J

ACS-36
[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
Revision: 2004 November 2004 FX35/FX45
CAUTION:
If “ICC” cannot be shown after several attempts, the ICC unit may have had malfunction. Repair or
replace it. Refer to GI-40, "
CONSULT-II Data Link Connector (DLC) Circuit" .
4. Self-diagnostic result appears on screen. If “NO DTC ···” is shown, check ICC warning lamp. If any mal-
function is indicated, GO TO step 5.
5. According to ACS-40, "
Diagnostic Trouble Code (DTC) Chart" , perform appropriate check, and repair or
replace malfunctioning part as necessary.
6. Turn ignition switch OFF.
7. Start engine and touch “START”, “ICC”, “SELF-DIAG RESULT”, and “ERASE” on CONSULT-II display in
turn to erase the memory.
CAUTION:
If the memory does not erase, go to 5.
8. Perform ICC system running test (drive vehicle with ICC system ON), and make sure that ICC warning
lamp does not illuminate.
WITHOUT CONSULT-II
1. Go to operation check after asking the customer for symptom information. Refer to ACS-9, "ACTION
TEST" .
2. Stop the vehicle to start the self-diagnosis.
3. Turn ignition switch OFF.
4. Turn ignition switch ON, and within 5 to 10 seconds, press
ACCEL/RES switch 5 times. Then press COAST/SET switch 5
times to start self-diagnosis.
CAUTION:

Do not start the engine.

Do not turn the ON/OFF switch ON.

When operation above is not completed within 5 to 10 sec-
onds, start again from above go to 3.

If self-diagnosis mode cannot be started after several
attempts, the ICC unit may have had malfunction. Repair or
replace it. Refer to ACS-37, "
SELF-DIAGNOSIS BY ICC SYS-
TEM DISPLAY WILL NOT RUN." .
5. When self-diagnosis mode is started, DTC are shown on set vehicle speed indicator.
CAUTION:

DTC will disappear after 5 minutes.
SKIA7067E
SKIA1236E

TROUBLE DIAGNOSIS FOR SYMPTOMS
ACS-63
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
2. CAN COMMUNICATION INSPECTION
With CONSULT-II
1. With CONSULT-II self-diagnosis, check that “CAN COMM CIRCUIT” item exists.
OK or NG
OK >> Refer to ACS-41, "DTC 20 CAN COMM CIRCUIT" .
NG >> After replacing combination meter, erase DTC. Perform ICC system running test, and then per-
form self-diagnosis of ICC system again.
Symptom 6: Driving Force Is Hunting.AKS006ZU
1. CHECK ECM
1. Perform self-diagnosis of ECM.
OK or NG
OK >> Refer toACS-63, "Symptom 7: The ICC System Frequently Cannot Detect the Vehicle Ahead/The
Detection Zone Is Short." .
NG >> After repairing applicable parts, erase DTC. Perform ICC system running test, and then perform
self-diagnosis of ICC system again.
Symptom 7: The ICC System Frequently Cannot Detect the Vehicle Ahead/The
Detection Zone Is Short.
AKS006ZV
The detection function may become unstable in the following cases:

When the reflector of the vehicle ahead is deficient/ not clean enough to reflect the radar.

When driving a road with extremely sharp corners.

When the radar cannot detect the reflector of the vehicle ahead as the vehicle ahead is passing a hill or
passing the peak.
1. VISUAL CHECK
1. Check ICC sensor body window for contamination and foreign materials.
OK or NG
OK >> If any contamination or foreign materials are found, remove them. Then perform ICC system run-
ning test.
NG >> GO TO 2.
2. CHECK FUNCTION
1. After adjusting ICC sensor beam aiming, perform ICC system running test. Check that preceding vehicle
detection performance has been improved.
OK or NG
OK >> INSPECTION END
NG >>

Replace ICC sensor, and perform laser beam aiming adjustment.

After performing above. Perform ICC system running test, and then perform self-diagnosis of
ICC system again.
Symptom 8: The System Does Not Detect the Vehicle Ahead at All.AKS006ZW
1. VISUAL CHECK
1. With ignition switch turned ON (engine not started), check that all indicator lamps in ICC system display
are continuously lit. (Check for a missing segment in preceding vehicle detection display.)
OK or NG
OK >> GO TO 2.
NG >> Check for combination meter. Refer to DI-13, "
How to Proceed With Trouble Diagnosis" in DI.

AT-1
AUTOMATIC TRANSMISSION
C TRANSMISSION/TRANSAXLE
CONTENTS
D
E
F
G
H
I
J
K
L
M
SECTION AT
A
B
AT
Revision: 2004 November 2004 FX35/FX45
AUTOMATIC TRANSMISSION
INDEX FOR DTC ........................................................ 5
Alphabetical Index .................................................... 5
DTC No. Index ......................................................... 6
PRECAUTIONS .......................................................... 7
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 7
Precautions for On Board Diagnostic (OBD) System
of A/T and Engine .................................................... 7
Precautions .............................................................. 8
Service Notice or Precautions .................................. 9
Wiring Diagrams and Trouble Diagnosis .................. 9
PREPARATION ......................................................... 10
Special Service Tools ............................................. 10
Commercial Service Tools ....................................... 11
A/T FLUID ................................................................. 12
Changing A/T Fluid ................................................ 12
Checking A/T Fluid ................................................. 12
A/T Fluid Cooler Cleaning ...................................... 14
A/T CONTROL SYSTEM .......................................... 17
Cross-Sectional View (2WD Models) ..................... 17
Cross-Sectional View (AWD Models) ..................... 18
Shift Mechanism ..................................................... 19
TCM Function ......................................................... 30
CAN Communication .............................................. 31
Input/Output Signal of TCM .................................... 31
Line Pressure Control ............................................ 32
Shift Control ........................................................... 33
Lock-up Control ...................................................... 34
Engine Brake Control ............................................. 36
Control Valve .......................................................... 36
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 38
Introduction ............................................................ 38
OBD-II Function for A/T System ............................. 38
One or Two Trip Detection Logic of OBD-II ............ 38
OBD-II Diagnostic Trouble Code (DTC) ................. 38
Malfunction Indicator Lamp (MIL) ........................... 41
TROUBLE DIAGNOSIS ............................................ 42
DTC Inspection Priority Chart ................................ 42
Fail-Safe ................................................................. 42How To Perform Trouble Diagnosis For Quick and
Accurate Repair ...................................................... 44
A/T Electrical Parts Location .................................. 49
Circuit Diagram ....................................................... 50
Inspections Before Trouble Diagnosis .................... 51
Check Before Engine is Started .............................. 55
Check at Idle ........................................................... 55
Cruise Test - Part 1 ................................................. 57
Cruise Test - Part 2 ................................................. 60
Cruise Test - Part 3 ................................................. 61
Vehicle Speed When Shifting Gears ...................... 62
Vehicle Speed When Performing and Releasing
Complete Lock-up .................................................. 63
Vehicle Speed When Performing and Releasing
Slip Lock-up ............................................................ 64
Symptom Chart ....................................................... 65
TCM Input/Output Signal Reference Values ........... 90
CONSULT-II ............................................................ 91
Diagnostic Procedure Without CONSULT-II .........103
DTC U1000 CAN COMMUNICATION LINE ............105
Description ............................................................105
On Board Diagnosis Logic ....................................105
Possible Cause .....................................................105
DTC Confirmation Procedure ...............................105
Wiring Diagram — AT — CAN ..............................106
Diagnostic Procedure ...........................................107
DTC P0615 START SIGNAL CIRCUIT ...................108
Description ............................................................108
CONSULT-II Reference Value ..............................108
On Board Diagnosis Logic ....................................108
Possible Cause .....................................................108
DTC Confirmation Procedure ...............................108
Wiring Diagram — AT — STSIG ..........................109
Diagnostic Procedure ...........................................110
DTC P0705 PARK/NEUTRAL POSITION SWITCH .112
Description ............................................................112
CONSULT-II Reference Value ..............................112
On Board Diagnosis Logic ....................................112
Possible Cause .....................................................112
DTC Confirmation Procedure ...............................112

AT-2Revision: 2004 November 2004 FX35/FX45Wiring Diagram — AT — PNP/SW .......................113
Diagnostic Procedure ...........................................114
DTC P0720 VEHICLE SPEED SENSOR A/T (REV-
OLUTION SENSOR) ...............................................116
Description ............................................................116
CONSULT-II Reference Value ..............................116
On Board Diagnosis Logic ....................................116
Possible Cause .....................................................116
DTC Confirmation Procedure ...............................116
Wiring Diagram — AT — VSSA/T .........................118
Diagnostic Procedure ...........................................119
DTC P0725 ENGINE SPEED SIGNAL ...................121
Description ............................................................121
CONSULT-II Reference Value ..............................121
On Board Diagnosis Logic ....................................121
Possible Cause .....................................................121
DTC Confirmation Procedure ...............................121
Diagnostic Procedure ...........................................121
DTC P0740 TORQUE CONVERTER CLUTCH
SOLENOID VALVE .................................................123
Description ............................................................123
CONSULT-II Reference Value ..............................123
On Board Diagnosis Logic ....................................123
Possible Cause .....................................................123
DTC Confirmation Procedure ...............................123
Diagnostic Procedure ...........................................124
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP) .125
Description ............................................................125
CONSULT-II Reference Value ..............................125
On Board Diagnosis Logic ....................................125
Possible Cause .....................................................125
DTC Confirmation Procedure ...............................125
Diagnostic Procedure ...........................................126
DTC P0745 LINE PRESSURE SOLENOID VALVE .127
Description ............................................................127
CONSULT-II Reference Value ..............................127
On Board Diagnosis Logic ....................................127
Possible Cause .....................................................127
DTC Confirmation Procedure ...............................127
Diagnostic Procedure ...........................................128
DTC P1701 TRANSMISSION CONTROL MODULE
(POWER SUPPLY) ..................................................129
Description ............................................................129
On Board Diagnosis Logic ....................................129
Possible Cause .....................................................129
DTC Confirmation Procedure ...............................129
Wiring Diagram — AT — POWER ........................130
Diagnostic Procedure ...........................................131
DTC P1702 TRANSMISSION CONTROL MODULE
(RAM) ......................................................................133
Description ............................................................133
On Board Diagnosis Logic ....................................133
Possible Cause .....................................................133
DTC Confirmation Procedure ...............................133
Diagnostic Procedure ...........................................133
DTC P1703 TRANSMISSION CONTROL MODULE
(ROM) ......................................................................134
Description ............................................................134
On Board Diagnosis Logic ....................................134Possible Cause .....................................................134
DTC Confirmation Procedure ................................134
Diagnostic Procedure ............................................134
DTC P1704 TRANSMISSION CONTROL MODULE
(EEPROM) ...............................................................135
Description ............................................................135
On Board Diagnosis Logic ....................................135
Possible Cause .....................................................135
DTC Confirmation Procedure ................................135
Diagnostic Procedure ............................................135
DTC P1705 THROTTLE POSITION SENSOR ........136
Description ............................................................136
CONSULT-II Reference Value ...............................136
On Board Diagnosis Logic ....................................136
Possible Cause .....................................................136
DTC Confirmation Procedure ................................136
Diagnostic Procedure ............................................136
DTC P1710 A/T FLUID TEMPERATURE SENSOR
CIRCUIT ..................................................................139
Description ............................................................139
CONSULT-II Reference Value ...............................139
On Board Diagnosis Logic ....................................139
Possible Cause .....................................................139
DTC Confirmation Procedure ................................139
Wiring Diagram — AT — FTS ...............................140
Diagnostic Procedure ............................................141
Component Inspection ..........................................142
DTC P1716 TURBINE REVOLUTION SENSOR ....143
Description ............................................................143
CONSULT-II Reference Value ...............................143
On Board Diagnosis Logic ....................................143
Possible Cause .....................................................143
DTC Confirmation Procedure ................................143
Diagnostic Procedure ............................................144
DTC P1721 VEHICLE SPEED SENSOR MTR .......145
Description ............................................................145
CONSULT-II Reference Value ...............................145
On Board Diagnosis Logic ....................................145
Possible Cause .....................................................145
DTC Confirmation Procedure ................................145
Diagnostic Procedure ............................................146
DTC P1730 A/T INTERLOCK .................................147
Description ............................................................147
On Board Diagnosis Logic ....................................147
Possible Cause .....................................................147
DTC Confirmation Procedure ................................147
Judgement of A/T Interlock ...................................147
Diagnostic Procedure ............................................148
DTC P1731 A/T 1ST ENGINE BRAKING ...............150
Description ............................................................150
CONSULT-II Reference Value ...............................150
On Board Diagnosis Logic ....................................150
Possible Cause .....................................................150
DTC Confirmation Procedure ................................150
Diagnostic Procedure ............................................151
DTC P1752 INPUT CLUTCH SOLENOID VALVE ..152
Description ............................................................152
CONSULT-II Reference Value ...............................152
On Board Diagnosis Logic ....................................152

AT-4Revision: 2004 November 2004 FX35/FX45CONSULT-II Reference Value ..............................187
Diagnostic Procedure ...........................................187
TROUBLE DIAGNOSIS FOR SYMPTOMS ............188
Wiring Diagram — AT — NONDTC ......................188
A/T CHECK Indicator Lamp Does Not Come On . 191
Engine Cannot Be Started In “P” or “N” Position ..193
In “P” Position, Vehicle Moves When Pushed ......193
In “N” Position, Vehicle Moves ..............................194
Large Shock (“N” to “D” Position) .........................195
Vehicle Does Not Creep Backward In “R” Position .198
Vehicle Does Not Creep Forward In “D” Position . 201
Vehicle Cannot Be Started From D
1 .....................203
A/T Does Not Shift: D
1 → D2 ................................206
A/T Does Not Shift: D
2 → D3 ................................208
A/T Does Not Shift: D
3 → D4 ................................211
A/T Does Not Shift: D
4 → D5 ................................213
A/T Does Not Perform Lock-up ............................216
A/T Does Not Hold Lock-up Condition ..................218
Lock-up Is Not Released ......................................220
Engine Speed Does Not Return To Idle ................221
Cannot Be Changed to Manual Mode ..................222
A/T Does Not Shift: 5th gear → 4th gear ..............223
A/T Does Not Shift: 4th gear → 3rd gear ..............225
A/T Does Not Shift: 3rd gear → 2nd gear .............227
A/T Does Not Shift: 2nd gear → 1st gear .............229
Vehicle Does Not Decelerate By Engine Brake ....231
SHIFT CONTROL SYSTEM ....................................233
Control Device Removal and Installation ..............233
Adjustment of A/T Position ...................................234
Checking of A/T Position ......................................234
A/T SHIFT LOCK SYSTEM .....................................235
Description ............................................................235
Shift Lock System Electrical Parts Location .........235
Wiring Diagram — AT — SHIFT ...........................236
Diagnostic Procedure ...........................................237
KEY INTERLOCK CABLE ......................................239
Components .........................................................239
Removal and Installation ......................................240
ON-VEHICLE SERVICE ..........................................242
Control Valve with TCM and A/T Fluid Temperature
Sensor 2 ...............................................................242
Parking Components (2WD Models Only) ............253Rear Oil Seal .........................................................259
Revolution Sensor Components (2WD Models
Only) .....................................................................260
AIR BREATHER HOSE ...........................................264
Removal and Installation .......................................264
TRANSMISSION ASSEMBLY .................................266
Removal and Installation (2WD Models) ...............266
Removal and Installation (AWD models) ..............269
OVERHAUL .............................................................274
Components ..........................................................274
Oil Channel ...........................................................282
Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings ..........................284
DISASSEMBLY .......................................................286
Disassembly ..........................................................286
REPAIR FOR COMPONENT PARTS ......................303
Oil Pump ...............................................................303
Front Sun Gear, 3rd One-Way Clutch ...................306
Front Carrier, Input Clutch, Rear Internal Gear .....308
Mid Sun Gear, Rear Sun Gear, High and Low
Reverse Clutch Hub ..............................................314
High and Low Reverse Clutch ..............................320
Direct Clutch .........................................................323
ASSEMBLY .............................................................325
Assembly (1) .........................................................325
Adjustment ............................................................338
Assembly (2) .........................................................341
SERVICE DATA AND SPECIFICATIONS (SDS) ....348
General Specifications ..........................................348
Vehicle Speed When Shifting Gears .....................348
Vehicle Speed When Performing and Releasing
Complete Lock-up .................................................349
Vehicle Speed When Performing and Releasing
Slip Lock-up ..........................................................349
Stall Speed ............................................................350
Line Pressure ........................................................350
A/T Fluid Temperature Sensor ..............................350
Turbine Revolution Sensor ....................................350
Vehicle Speed Sensor A/T (Revolution Sensor) ...350
Reverse Brake ......................................................350
Total End Play .......................................................351