2004 INFINITI FX35 engine spec

SERVICE DATA AND SPECIFICATIONS (SDS)
AT-349
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
Vehicle Speed When Performing and Releasing Complete Lock-up ACS002S4
2WD MODELS

At closed throttle, the accelerator opening is less than 1/8 condition.

At half throttle, the accelerator opening is 4/8 of the full opening.
AWD MODELS

At closed throttle, the accelerator opening is less than 1/8 condition.

At half throttle, the accelerator opening is 4/8 of the full opening.

At closed throttle, the accelerator opening is less than 1/8 condition.

At half throttle, the accelerator opening is 4/8 of the full opening.
Vehicle Speed When Performing and Releasing Slip Lock-upACS002S5
2WD MODELS

At closed throttle, the accelerator opening is less than 1/8 condition.
AWD MODELS

At closed throttle, the accelerator opening is less than 1/8 condition. Engine model VQ35DE
Throttle positionVehicle speed km/h (MPH)
Lock-up “ON” Lock-up “OFF”
Closed throttle 63 - 73 (39 - 45) 40 - 48 (25 - 30)
Half throttle 196 - 204 (122 - 127) 153 - 161 (95 - 100)
Engine model VQ35DE
Throttle positionVehicle speed km/h (MPH)
Lock-up “ON” Lock-up “OFF”
Closed throttle 59 - 67 (37 - 42) 56 - 64 (35 - 40)
Half throttle 178 - 186 (111 - 116) 139 - 147 (86 - 91)
Engine model VK45DE
Throttle positionVehicle speed km/h (MPH)
Lock-up “ON” Lock-up “OFF”
Closed throttle 66 - 74 (41 - 46) 53 - 61 (33 - 38)
Half throttle 191 - 199 (119 - 124) 136 - 144 (85 - 89)
Engine modelVQ35DE
Throttle position Gear positionVehicle speed km/h (MPH)
Slip lock-up “ON” Slip lock-up “OFF”
Closed throttle4th 43 - 51 (27 - 32) 40 - 48 (25 - 30)
5th 51 - 59 (32 - 37) 48 - 56 (30 - 35)
Engine modelVQ35DE
Throttle position Gear positionVehicle speed km/h (MPH)
Slip lock-up “ON” Slip lock-up “OFF”
Closed throttle4th 40 - 48 (25 - 30) 36 - 44 (22 - 27)
5th 48 - 56 (30 - 35) 45 - 53 (28 - 33)
Engine modelVK45DE
Throttle position Gear positionVehicle speed km/h (MPH)
Slip lock-up “ON” Slip lock-up “OFF”
Closed throttle4th 39 - 47 (24 - 29) 34 - 42 (21 - 26)
5th 47 - 55 (29 - 34) 44 - 52 (27 - 32)

AT-350
SERVICE DATA AND SPECIFICATIONS (SDS)
Revision: 2004 November 2004 FX35/FX45

At closed throttle, the accelerator opening is less than 1/8 condition.
Stall SpeedACS002S6
Line PressureACS002S7
A/T Fluid Temperature SensorACS007HG
Turbine Revolution SensorACS007HH
Vehicle Speed Sensor A/T (Revolution Sensor)ACS007HI
Reverse BrakeACS007HJ
*: Always check with the Parts Department for the latest parts information.Engine modelVQ35DE
Stall speed2,650 - 2,950 rpm
Engine modelVK45DE
Stall speed2,300 - 2,600 rpm
Engine speedLine pressure kPa (kg/cm
2 , psi)
R position D, M positions
At idle speed 392 - 441 (4.0 - 4.5, 57 - 64) 373 - 422 (3.8 - 4.3, 54 - 61)
At stall speed 1,700 - 1,890 (17.3 - 19.3, 247 - 274) 1,310 - 1,500 (13.3 - 15.3, 190 - 218)
Name Condition CONSULT-II “DATA MONITOR” (Approx.) (V) Resistance (Approx.) (kΩ)
A/T fluid temperature sensor 10°C (32°F) 2.2 15
20°C (68°F) 1.8 6.5
80°C (176°F) 0.6 0.9
A/T fluid temperature sensor 20°C (32°F) 2.2 10
20°C (68°F) 1.7 4
80°C (176°F) 0.45 0.5
Name Condition Data (Approx.)
Turbine revolution
sensor 1When running at 50 km/h (31 MPH) in 4th speed with the closed throttle position switch
“OFF”.
1.3 (kHz)
Turbine revolution
sensor 2When moving at 20 km/h (12 MPH) in 1st speed with the closed throttle position switch
“OFF”.
Name Condition Data (Approx.)
Revolution sensor When moving at 20 km/h (12 MPH). 185 (Hz)
Thickness of retaining platesThickness mm (in) Part number*
4.2 (0.165)
4.4 (0.173)
4.6 (0.181)
4.8 (0.189)
5.0 (0.197)
5.2 (0.205) 31667 90X14
31667 90X15
31667 90X16
31667 90X17
31667 90X18
31667 90X19

ATC-2Revision: 2004 November 2004 FX35/FX45DUAL SWITCH (WITH LEFT AND RIGHT VEN-
TILATION TEMPERATURE SEPARATELY
CONTROL SYSTEM) .......................................... 35
Fail-safe Function ................................................... 36
Discharge Air Flow ................................................. 37
System Description ................................................. 38
SWITCHES AND THEIR CONTROL FUNCTION ... 38
CAN Communication System Description .............. 39
TROUBLE DIAGNOSIS ............................................ 40
CONSULT-II ............................................................ 40
CONSULT-II BASIC OPERATION ....................... 40
DATA MONITOR .................................................. 41
How to Perform Trouble Diagnosis for Quick and
Accurate Repair ...................................................... 42
WORK FLOW ...................................................... 42
SYMPTOM TABLE .............................................. 42
Component Parts and Harness Connector Location ... 43
ENGINE COMPARTMENT .................................. 43
PASSENGER COMPARTMENT .......................... 44
Schematic ............................................................... 45
Wiring Diagram —A/C— ......................................... 46
Auto Amp. Terminals and Reference Value ............ 51
PIN CONNECTOR TERMINAL LAYOUT ............ 51
TERMINALS AND REFERENCE VALUE FOR
UNIFIED METER AND A/C AMP. ........................ 51
Self-diagnosis Function .......................................... 53
DESCRIPTION .................................................... 53
FUNCTION CONFIRMATION PROCEDURE ...... 54
AUXILIARY MECHANISM: TEMPERATURE
SETTING TRIMMER ........................................... 59
AUXILIARY MECHANISM: FOOT POSITION
SETTING TRIMMER ........................................... 60
AUXILIARY MECHANISM: INLET PORT MEM-
ORY FUNCTION ................................................. 60
Operational Check .................................................. 61
CHECKING MEMORY FUNCTION ..................... 61
CHECKING BLOWER ......................................... 61
CHECKING DISCHARGE AIR ............................ 61
CHECKING RECIRCULATION ............................ 62
CHECKING TEMPERATURE DECREASE ......... 62
CHECKING TEMPERATURE INCREASE .......... 62
CHECK A/C SWITCH .......................................... 62
CHECKING AUTO MODE ................................... 63
Power Supply and Ground Circuit for Auto Amp. ... 63
INSPECTION FLOW ........................................... 63
COMPONENT DESCRIPTION ............................ 64
DIAGNOSTIC PROCEDURE FOR A/C SYSTEM ... 64
LAN System Circuit ................................................ 66
DIAGNOSTIC PROCEDURE FOR LAN CIR-
CUIT .................................................................... 66
Mode Door Motor Circuit ........................................ 70
INSPECTION FLOW ........................................... 70
SYSTEM DESCRIPTION .................................... 71
COMPONENT DESCRIPTION ............................ 72
DIAGNOSTIC PROCEDURE FOR MODE
DOOR MOTOR ................................................... 72
Air Mix Door Motor Circuit ...................................... 73
INSPECTION FLOW ........................................... 73SYSTEM DESCRIPTION ..................................... 74
COMPONENT DESCRIPTION ............................ 75
DIAGNOSTIC PROCEDURE FOR AIR MIX
DOOR .................................................................. 75
Air Mix Door Motor PBR Circuit .............................. 75
DIAGNOSTIC PROCEDURE FOR AIR MIX
DOOR PBR .......................................................... 75
Intake Door Motor Circuit ........................................ 76
INSPECTION FLOW ............................................ 76
SYSTEM DESCRIPTION ..................................... 77
COMPONENT DESCRIPTION ............................ 78
DIAGNOSTIC PROCEDURE FOR INTAKE
DOOR MOTOR .................................................... 78
Blower Motor Circuit ................................................ 79
INSPECTION FLOW ............................................ 79
SYSTEM DESCRIPTION ..................................... 80
COMPONENT DESCRIPTION ............................ 81
DIAGNOSTIC PROCEDURE FOR BLOWER
MOTOR ................................................................ 81
COMPONENT INSPECTION ............................... 83
Magnet Clutch Circuit .............................................. 84
INSPECTION FLOW ............................................ 84
SYSTEM DESCRIPTION ..................................... 85
DIAGNOSTIC PROCEDURE FOR MAGNET
CLUTCH .............................................................. 85
COMPONENT INSPECTION ............................... 90
Insufficient Cooling .................................................. 91
INSPECTION FLOW ............................................ 91
PERFORMANCE TEST DIAGNOSIS .................. 93
PERFORMANCE CHART .................................... 95
TROUBLE DIAGNOSIS FOR UNUSUAL PRES-
SURE ................................................................... 96
DIAGNOSTIC PROCEDURE FOR INSUFFI-
CIENT COOLING ................................................. 98
Insufficient Heating ...............................................100
INSPECTION FLOW ..........................................100
Noise .....................................................................101
INSPECTION FLOW ..........................................101
Self-diagnosis .......................................................102
INSPECTION FLOW ..........................................102
Memory Function ..................................................103
INSPECTION FLOW ..........................................103
Ambient Sensor Circuit .........................................104
COMPONENT DESCRIPTION ..........................104
AMBIENT TEMPERATURE INPUT PROCESS .104
DIAGNOSTIC PROCEDURE FOR AMBIENT
SENSOR ............................................................104
COMPONENT INSPECTION .............................106
In-vehicle Sensor Circuit .......................................107
COMPONENT DESCRIPTION ..........................107
DIAGNOSTIC PROCEDURE FOR IN-VEHICLE
SENSOR ............................................................108
COMPONENT INSPECTION .............................109
Sunload Sensor Circuit .........................................110
COMPONENT DESCRIPTION ..........................110
SUNLOAD INPUT PROCESS ...........................110
DIAGNOSTIC PROCEDURE FOR SUNLOAD
SENSOR ............................................................110

ATC-3
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2004 November 2004 FX35/FX45COMPONENT INSPECTION ............................. 112
Intake Sensor Circuit ............................................. 113
COMPONENT DESCRIPTION .......................... 113
DIAGNOSTIC PROCEDURE FOR INTAKE SEN-
SOR ................................................................... 113
COMPONENT INSPECTION ............................. 114
CONTROLLER ........................................................115
Removal and Installation of A/C and AV Switch .... 115
REMOVAL .......................................................... 115
INSTALLATION .................................................. 115
AUTO AMP ..............................................................116
Removal and Installation of Unified Meter and A/C
Amp. ...................................................................... 116
REMOVAL .......................................................... 116
INSTALLATION .................................................. 116
AMBIENT SENSOR .................................................117
Removal and Installation ....................................... 117
REMOVAL .......................................................... 117
INSTALLATION .................................................. 117
IN-VEHICLE SENSOR .............................................118
Removal and Installation ....................................... 118
REMOVAL .......................................................... 118
INSTALLATION .................................................. 118
SUNLOAD SENSOR ...............................................119
Removal and Installation ....................................... 119
REMOVAL .......................................................... 119
INSTALLATION .................................................. 119
INTAKE SENSOR ................................................... 120
Removal and Installation ...................................... 120
REMOVAL ......................................................... 120
INSTALLATION ................................................. 120
BLOWER UNIT ....................................................... 121
Removal and Installation ...................................... 121
REMOVAL ......................................................... 121
INSTALLATION ................................................. 121
Disassembly and Assembly ................................. 122
BLOWER MOTOR .................................................. 123
Removal and Installation ...................................... 123
REMOVAL ......................................................... 123
INSTALLATION ................................................. 123
INTAKE DOOR MOTOR ......................................... 124
Removal and Installation ...................................... 124
REMOVAL ......................................................... 124
INSTALLATION ................................................. 124
IN-CABIN MICROFILTER ....................................... 125
Removal and Installation ...................................... 125
FUNCTION ........................................................ 125
REPLACEMENT TIMING .................................. 125
REPLACEMENT PROCEDURES ..................... 125
HEATER & COOLING UNIT ASSEMBLY .............. 126
Removal and Installation ...................................... 126
REMOVAL ......................................................... 126
INSTALLATION ................................................. 127
Disassembly and Assembly ................................. 128
MODE DOOR MOTOR ........................................... 130
Removal and Installation ...................................... 130
REMOVAL ......................................................... 130
INSTALLATION ................................................. 130AIR MIX DOOR MOTOR .........................................131
Removal and Installation ......................................131
REMOVAL .........................................................131
INSTALLATION .................................................131
HEATER CORE .......................................................132
Removal and Installation ......................................132
REMOVAL .........................................................132
INSTALLATION .................................................132
DUCTS AND GRILLES ...........................................133
Removal and Installation ......................................133
REMOVAL .........................................................133
INSTALLATION .................................................136
REFRIGERANT LINES ...........................................137
HFC-134a (R-134a) Service Procedure ...............137
SETTING OF SERVICE TOOLS AND EQUIP-
MENT ................................................................137
Components .........................................................139
VK45DE .............................................................139
VQ35DE ............................................................140
Removal and Installation of Compressor ..............140
REMOVAL .........................................................140
INSTALLATION .................................................142
Removal and Installation of Compressor Clutch ..143
REMOVAL .........................................................143
INSTALLATION .................................................145
Removal and Installation of Low-pressure Flexible
Hose .....................................................................147
REMOVAL .........................................................147
INSTALLATION .................................................148
Removal and Installation of High-pressure Flexible
Hose .....................................................................148
REMOVAL .........................................................148
INSTALLATION .................................................149
Removal and Installation of Low-pressure Pipe 1
(Engine Compartment) .........................................149
REMOVAL .........................................................149
INSTALLATION .................................................150
Removal and Installation of High-pressure Pipe 1
and 2 (Engine Compartment) ...............................150
REMOVAL .........................................................150
INSTALLATION .................................................151
Removal and Installation of Low-pressure Pipe 2
and High-pressure Pipe 3 .....................................151
REMOVAL .........................................................151
INSTALLATION .................................................152
Removal and Installation of Liquid Tank ...............153
REMOVAL .........................................................153
INSTALLATION .................................................153
Removal and Installation of Condenser ................154
REMOVAL .........................................................154
INSTALLATION .................................................154
Removal and Installation of Refrigerant Pressure
Sensor ..................................................................155
REMOVAL .........................................................155
INSTALLATION .................................................155
Removal and Installation of Evaporator ................155
REMOVAL .........................................................155
INSTALLATION .................................................155
Removal and Installation of Expansion Valve .......156

ATC-4Revision: 2004 November 2004 FX35/FX45REMOVAL .........................................................156
INSTALLATION ..................................................156
Checking for Refrigerant Leaks ............................157
Checking System for Leaks Using the Fluorescent
Leak Detector .......................................................157
Dye Injection .........................................................157
Electronic Refrigerant Leak Detector ....................158
PRECAUTIONS FOR HANDLING LEAK DETECTOR .......................................................158
CHECKING PROCEDURE ................................159
SERVICE DATA AND SPECIFICATIONS (SDS) ....161
Compressor ..........................................................161
Lubricant ...............................................................161
Refrigerant ............................................................161
Engine Idling Speed ..............................................161
Belt Tension ..........................................................161

PRECAUTIONS
ATC-13
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2004 November 2004 FX35/FX45

After connecting line, perform leak test and make sure that there is no leakage from connections.
When the gas leaking point is found, disconnect that line and replace the O-ring. Then tighten con-
nections of seal seat to the specified torque.
Precautions for Servicing CompressorAJS0013Z

Plug all openings to prevent moisture and foreign matter from entering.

When the compressor is removed, store it in the same position as it is when mounted on the car.

When replacing or repairing compressor, follow “Maintenance of Lubricant Quantity in Compres-
sor” exactly. Refer to AT C - 2 7 , "
Maintenance of Lubricant Quantity in Compressor" .

Keep friction surfaces between clutch and pulley clean. If the surface is contaminated, with lubri-
cant, wipe it off by using a clean waste cloth moistened with thinner.

After compressor service operation, turn the compressor shaft by hand more than five turns in
both directions. This will equally distribute lubricant inside the compressor. After the compressor
is installed, let the engine idle and operate the compressor for one hour.

After replacing the compressor magnet clutch, apply voltage to the new one and check for usual
operation.
Precautions for Service EquipmentAJS00140
RECOVERY/RECYCLING EQUIPMENT
Be certain to follow the manufacturer’s instructions for machine operation and machine maintenance. Never
introduce any refrigerant other than that specified into the machine.
ELECTRONIC LEAK DETECTOR
Be certain to follow the manufacturer’s instructions for tester operation and tester maintenance.
RHA861F

ATC-16
PRECAUTIONS
Revision: 2004 November 2004 FX35/FX45
Precautions for Leak Detection DyeAJS00141

The A/C system contains a fluorescent leak detection dye used for locating refrigerant leaks. An ultraviolet
(UV) lamp is required to illuminate the dye when inspecting for leaks.

Always wear fluorescence enhancing UV safety goggles to protect your eyes and enhance the visibility of
the fluorescent dye.

The fluorescent dye leak detector is not a replacement for an electronic refrigerant leak detector. The fluo-
rescent dye leak detector should be used in conjunction with an electronic refrigerant leak detector to (J-
41995) pin-point refrigerant leaks.

For your safety and your customer′s satisfaction, read and follow all manufacture′s operating instructions
and precautions prior to performing the work.

A compressor shaft seal should not be repaired because of dye seepage. The compressor shaft seal
should only be repaired after confirming the leak with an electronic refrigerant leak detector (J-41995).

Always remove any remaining dye from the leak area after repairs are complete to avoid a misdiagnosis
during a future service.

Do not allow dye to come into contact with painted body panels or interior components. If dye is spilled,
clean immediately with the approved dye cleaner. Fluorescent dye left on a surface for an extended period
of time cannot be removed.

Do not spray the fluorescent dye cleaning agent on hot surfaces (engine exhaust manifold, etc.).

Do not use more than one refrigerant dye bottle (1/4 ounce /7.4 cc) per A/C system.

Leak detection dyes for HFC-134a (R-134a) and CFC-12 (R-12) A/C systems are different. Do not use
HFC-134a (R-134a) leak detection dye in CFC-12 (R-12) A/C system or CFC-12 (R-12) leak detector dye
in HFC-134a (R-134a) A/C system or A/C system damage may result.

The fluorescent properties of the dye will remain for over three (3) years unless a compressor malfunction
occurs.
IDENTIFICATION
NOTE:
Vehicles with factory installed fluorescent dye have a green label.
Vehicles without factory installed fluorescent dye have a blue label.
IDENTIFICATION LABEL FOR VEHICLE
Vehicles with factory installed fluorescent dye have this identification
label on the front side of hood.
Wiring Diagrams and Trouble DiagnosisAJS00142
When you read wiring diagrams, refer to the following:

GI-15, "How to Read Wiring Diagrams" in GI section.

PG-4, "Wiring Diagram - POWER -" in PG section.
When you perform trouble diagnosis, refer to the following:

GI-11, "How to Follow Trouble Diagnoses" in GI section.

GI-27, "How to Perform Efficient Diagnosis for an Electrical Incident" in GI section.
SHA436FA

LUBRICANT
ATC-27
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2004 November 2004 FX35/FX45
LUBRICANTPFP:KLG00
Maintenance of Lubricant Quantity in CompressorAJS00149
The lubricant in the compressor circulates through the system with the refrigerant. Add lubricant to compres-
sor when replacing any component or after a large refrigerant leakage occurred. It is important to maintain the
specified amount.
If lubricant quantity is not maintained properly, the following malfunctions may result:

Lack of lubricant: May lead to a seized compressor

Excessive lubricant: Inadequate cooling (thermal exchange interference)
LUBRICANT
LUBRICANT RETURN OPERATION
Adjust the lubricant quantity according to the test group shown below.
1. CHECK LUBRICANT RETURN OPERATION
Can lubricant return operation be performed?

A/C system works properly.

There is no evidence of a large amount of lubricant leakage.
CAUTION:
If excessive lubricant leakage is noted, do not perform the lubricant return operation.
YES or NO
YES >> GO TO 2.
NO >> GO TO 3.
2. PERFORM LUBRICANT RETURN OPERATION, PROCEEDING AS FOLLOWS:
1. Start engine, and set the following conditions:
–Test condition
Engine speed: Idling to 1,200 rpm
A/C switch: ON
Blower speed: Max. position
Temp. control: Optional [Set so that intake air temperature is 25 to 30°C (77 to 86°F).]
Intake position: Recirculation (REC)
2. Perform lubricant return operation for about 10 minutes.
3. Stop engine.
>> GO TO 3.
3. CHECK REPLACEMENT PART
Should the compressor be replaced?
YES >> GO TO AT C - 2 9 , "LUBRICANT ADJUSTING PROCEDURE FOR COMPRESSOR REPLACE-
MENT" .
NO >> GO TO AT C - 2 8 , "
LUBRICANT ADJUSTING PROCEDURE FOR COMPONENTS REPLACE-
MENT EXCEPT COMPRESSOR" . Name : NISSAN A/C System Oil Type S
Part number : KLH00-PAGS0