2004 Hyundai Getz length

1- 22 FEATURES OF YOUR HYUNDAI
B180A02A-GAT SEAT BELTS 3-Point System with Emergency Locking Retrac-
tor (If Installed)To Fasten Your Belt
B180A01L
To fasten your seat belt, pull it out of the retractor and insert the metal tabinto the buckle. There will be an au- dible "click" when the tab locks into the buckle.The seat belt automatically adjusts to the proper length only after the lap belt is adjusted manually so that it fitssnugly around your hips. If you lean forward in a slow, easy motion, the belt will extend and let you move around. Ifthere is a sudden stop or impact, how- ever, the belt will lock into position. It
B170A04A-AAT HEIGHT ADJUSTABLE FRONT SEAT SHOULDER BELT(If Installed)
B170A01L
You can adjust the height of the shoul- der belt anchor to one of the 4 posi- tions.If the height of the adjusting seat belt is too near your neck, you will not be getting the most effective protection.The shoulder portion should be adjusted so that it lies across your chest and midway over your shouldernearest the door and not your neck. To adjust the height of the seat belt anchor, lower or raise the height ad-juster into an appropriate position. To raise the height adjuster, pull it up. To lower it, push it down while pressingthe height adjuster button. Release the button to lock the anchorinto position. Try sliding the release button to make sure that it has locked into the position.
WARNING:
o The height adjuster must be in the locked position when thevehicle is moving.
o The misadjustment of height of
the shoulder belt could reduce the effectiveness of the seat belt in a crash.
!

1- 24 FEATURES OF YOUR HYUNDAI
B220A01Y-GAT SEAT BELTS - Rear Seat Center's 3-Point System WithEmergency Locking Retractor(If installed)
1. Before fastening the rear seat cen-
ter belt, confirm the metal tab (a) and buckle (b) are latched together.
2. After confirming that (a) and (b) are latched, pull the seat belt out of theretractor and insert the metal tab (c)into the buckle (d).
There will be an audible "click" when the tab locks in the buckle. The seat belt automatically adjusts to the properlength only after the lap belt is adjusted manually so that it fits snugly around HTB192
HTB226
Correct
Shorten Too high
B220B01A-AAT Adjusting Your Seat Belt With a 2-point static type seat belt, the length must be adjusted manually so it fits snugly around your body. Fastenthe belt and pull on the loose end to tighten. The belt should be placed as low as possible on your hips, not onyour waist. If the belt is too high, it could increase the possibility of your being injured in an accident. B220C01A-AAT To Release the Seat Belt
When you want to release the seat belt, press the button in the locking buckle. HTB190
WARNING:
The center lap belt latching mecha- nism is different from those for the rear seat shoulder belts. When fas-tening the rear seat shoulder belts or the center lap belt, make sure they are inserted into the correctbuckles to obtain maximum protec- tion from the seat belt system and assure proper operation.
!
(a)
(b) (c)
(d)

FEATURES OF YOUR HYUNDAI 1- 65
To adjust the position of either mirror:
1. Move the selecting switch to the
right or left to activate the adjustable mechanism for the correspondingdoor mirror.
2. Now, adjust mirror angle by de-
pressing the appropriate perimeterswitch as illustrated.
HTB213CAUTION:
o Do not operate the switch con- tinuously for an unnecessarylength of time.
o Scraping ice from the mirror face could cause permanent damage.To remove any ice, use a sponge,soft cloth or approved de-icer.
WARNING:
Be careful when judging the size ordistance of any object seen in the passenger side rear view mirror. It is a convex mirror with a curvedsurface. Any objects seen in this mirror are closer than they appear.
!
!
B510B01FC-GAT Electric Type (If installed) The outside rearview mirrors can be adjusted to your preferred rear vision, both directly behind the vehicle, and tothe rear of the left and right sides. The remote control outside rearview mirror switch controls the adjustmentsfor both right and left outside mirrors. HTB104

9- 2 VEHICLE SPECIFICATIONS
1.3 L
1.6 L
Type Wheel free playRack stroke Oil pump type 3,810 (150) 1,665(65.6) 1,495(58.9) 1,490(58.7)2,455(96.7) 1,450(57.1) 1,440(56.7)
Overall lengthOverall width Overall height (unladen)Wheel base Wheel tread J030A02TB-GAT TIRE1.1 L
13.5V,70A
Dual hydraulic with brake booster Ventilated disc DrumCable
J010A01TB-GAT MEASUREMENT
J060A01TB-GAT FUEL SYSTEM
Rack and pinion 0 ~ 30 mm (0 ~ 1.18 in.) 132 mm (5.20 in.)140 mm (5.5 in.) Vane type
155/80R13, 165/65R14 175/65R14, 185/55R15
StandardOption
Front Rear
mm (in.)
J020A01TB-GAT POWER STEERING
Fuel tank Capacity Liter
45 Imp.gal
9.9
J040A03TB-GAT ELECTRICAL
Item Battery Alternator
J050A01FC-GAT BRAKE Type Front brake typeRear brake type Parking brake
J035A01TB-GAT SPARE TIRE
T105/70D14(Temporary) Full size
Standard Option
DIESEL
1.5 L
60AH
12V, 90AGASOLINE
GEN EC
Manual Power 13.5V, 90A
45AH, 55AH

1- 20 FEATURES OF YOUR HYUNDAI
B200A01S-GAT
Adjusting Your Seat Belt
B200A01L-D You should place the belt as low as
possible on your hips, not on your
waist. If the belt is located too high on
your body, you could slide under it in
case of accident or a sudden stop.
This could result of death, serious
injury or property damage. Both arms
should not be under or over the belt.
Rather, one should be over and the
other under, as shown in the illustration.
Never wear the seat belt under the arm
nearest the door.
The mechanism will also lock if the seat
belt webbing is withdrawn too quickly
when the belt is being fastened or if
attempts are made to withdraw the
webbing whilst the vehicle is not on
level ground. Should the seat belt lock
under these conditions, it will be pos-
sible to release the mechanism by al-
lowing a small amount of webbing to be
retracted and the belt withdrawn again.
SB090P1-E
SEAT BELTS (3-Point Type)
To Fasten The Seat Belt
B180A01L-D
The seat belts are fastened by pulling
the belt buckle towards the seat belt
stalk and inserting the metal tongue of
the buckle into the stalk. The buckle
should be firmly pressed into the stalk
until locked which will be indicated by
an audible "click".
The length of the seat belt webbing will
be automatically adjusted by the seat
belt mechanism to allow the wearer
maximum freedom of movement whilst
the belt is being worn. However, in the
event of rapid deceleration or impact,
the belt mechanism will automatically
lock.
tbuk-1a.p65 3/23/04, 2:21 PM
20

FEATURES OF YOUR HYUNDAI 1- 21
B220A01Y-DAT
SEAT BELTS - Rear Seat
Centre's 3-Point System With
Emergency Locking Retractor
1. Before fastening the rear seat centre
belt, confirm the metal tab (a) and
buckle (b) are latched together.
2. After confirming that (a) and (b) are latched, pull the seat belt out of the
retractor and insert the metal tab (c)
into the buckle (d).
There will be an audible "click" when the
tab locks in the buckle. The seat belt
automatically adjusts to the proper length
only after the lap belt is adjusted manu-
ally so that it fits snugly around your HTB192
hips. If you lean forward in a slow, easy
motion, the belt will extend and let you
move around. If there is a sudden stop
or impact, the belt will lock into position.
It will also lock if you try to lean forward
too quickly.
(a)
(b) (c)
(d) B220A02YB210A01A-AAT
To Release the Seat Belt
The seat belt is released by pressing
the release button in the locking buckle.
When it is released, the belt should
automatically draw back into the re-
tractor.
If this does not happen, check the belt
to be sure it is not twisted, then try
again. B210A01L-D
tbuk-1a.p65
3/23/04, 2:21 PM
21

1- 60 FEATURES OF YOUR HYUNDAI
To adjust the position of either
mirror:
1. Move the selecting switch to the "L"
(or "R") position to activate the ad-
justable mechanism for the adjust-
ing door mirror.
2. Now, adjust mirror angle by depress-
ing the appropriate perimeter switch
as illustrated.
HTB213CAUTION:
o Do not leave the switch on for an unnecessary length of time.
o Scraping ice from the mirror face could cause permanent damage.
To remove any ice, use a sponge,
soft cloth or approved deicer.
o Be careful when judging the size or distance of any object seen in
the passenger side rear view mir-
ror. It is a convex mirror with a
curved surface, any objects seen
in this mirror are closer than they
appear.
!
B510B01FC-EAT
OUTSIDE REAR VIEW MIRROR
Electric Type (Not all models)
The outside rear view mirror can be
adjusted in any direction to give the
maximum rear view vision.
The remote control outside rear view
mirror switch controls the adjustments
for passenger side door mirror. HTB104-D
tbuk-1a.p65
3/23/04, 2:22 PM
60

9- 2 VEHICLE SPECIFICATIONS
1.3 L
1.6 L
Type Wheel free playRack stroke Oil pump type 150 (3,810) 65.6(1,665) 58.7(1,490) 96.7(2,455)57.1(1,450) 56.7(1,440)
Overall length Overall width Overall height (unladen) Wheel baseWheel tread J030A02TB-EAT TYRE1.1 L
13.5V,70A
Dual hydraulic with brake booster Ventilated disc DrumCable
J010A01TB-EAT MEASUREMENT
J060A01TB-DAT FUEL SYSTEM
Rack and pinion 0 ~ 1.18 in. (0 ~ 30 mm) 5.20 in. (132 mm) 5.5 in. (140 mm) Vane type
165/65R14 175/65R14, 185/55R15
StandardOption
Front Rear
in. (mm)
J020A01TB-EAT POWER STEERING
Fuel tank Capacity Litre
45 Imp.gal
9.9
J040A02TB-EAT ELECTRICAL
Item Battery Alternator
J050A01FC-GAT BRAKE Type Front brake typeRear brake type Parking brake
J035A03TB-EAT SPARE TYRE
Temporary (space-saver) (T 150/70 D14) Full size
1.1L 1.3/1.5/1.6L
DIESEL
1.5 L
60AH
12V, 90APETROL
Manual Power 13.5V, 90A
45AH
tbuk-9.p65
7/3/2008, 4:11 PM
2