2004 Hyundai Getz check oil

6- 16 DO-IT-YOURSELF MAINTENANCE
G100B01L
Recommended Oil
Use only the approved transaxle lubri-
cant. The recommended lubricants are
complete in themselves and the use of
additives is neither required nor recom-
mended. The use of additives may
invalidate the vehicle warranty.
Transaxle Lubricant Level
Checking
Ensure that the vehicle is parked on
level ground with the parking brake
firmly applied and the engine cool. Re-
move the level plug from the transaxle
when lubricant should begin to drip from
the level hole. If the level is low and no
lubricant is seen to drip, add the re-
G100B02A-EAT
TRANSAXLE FLUID LEVEL
CHECKING
The vehicle must be parked on level
ground with the parking brake firmly
applied and the engine at normal oper-
ating temperature. (Normal operating
temperature will only be achieved when
the vehicle has been driven for 6 miles
or more).
SG110A1-E
AUTOMATIC TRANSAXLE
FLUID
The automatic transaxle fluid level
should be checked and changed at
those intervals prescribed in the main-
tenance schedule. It is of paramount
importance that only the specified fluid
is used when replenishing or changing
the fluid. The use of other fluids may
irreparably damage the transaxle and
invalidate the manufacturers warranty.
In addition the ingress of dirt or lint may
prevent correct functioning of the
transaxle and care must be exercised
to prevent the ingress of such matter.
CAUTION:
The transaxle on fluid level must be
checked with the engine running and
at normal operating temperature and
therefore care must be exercised to
prevent injury occurring through
contact with rotating or hot parts of
the engine.
! G110B03A-AAT
Recommended Fluid
Your Hyundai automatic transaxle is
specially designed to operate with DIA-
MOND ATF SP-III or SK ATF SP-III.
Damage caused by a nonspecified fluid
is not covered by your new vehicle
limited warranty.
tbuk-6.p65
3/23/04, 4:26 PM
16

DO-IT-YOURSELF MAINTENANCE 6- 27
!
5. Open the bonnet.
6. Draw the vertical line (through the
center of each headlight beam pat-
tern) and the horizontal line (through
the center of each headlight beam
pattern) on the aiming screen.
And then, draw the horizontal paral-
lel line at 1.18 in. (30 mm ) under the
horizontal line.
7. Adjust each cut-off line of the low beam to the parallel line with a phillips
screwdriver - VERTICAL AIMING.
8. Adjust each cut-off line of the low
beam to each vertical line with a
phillips screwdriver - HORIZONTAL
AIMING. HTB269
Horizontal Aiming
Vertical
Aiming
G290A01FC-EAT
HEADLIGHT AIMING ADJUST-
MENT
Before performing aiming adjustment,
make sure of the following.
1. Keep all tires inflated to the correct pressure.
2. Place the vehicle on level ground
and press the front bumper and rear
bumper down several times. Place
the vehicle at a distance of 118 in.
(3,000 mm) from the test wall.
3. See that the vehicle is unloaded (except for full levels of coolant,
engine oil and fuel, and spare tire,
jack, and tools).
4. Clean the head lights lens and turn
on the headlight (low beam). WARNING:
Be sure to carefully wipe away any
water drained out in this manner,
because the fuel mixed in the water
might be ignited and result in a fire.
1. Remove the engine cover.
2. Disconnect the air intake hose from air cleaner cover.
3. Loosen the drain plug at the bottom
of the fuel filter.
4. Tighten the drain plug when water no longer comes out.
5. Check to be sure that the warning lamp illuminates when the ignition
key is turned to "ON", and that it
goes off when the engine is started.
If in doubt, consult your nearest au-
thorized HYUNDAI dealer.
G300B01FC
tbuk-6.p65 3/23/04, 4:27 PM
27

6- 28 DO-IT-YOURSELF MAINTENANCE
SPECIFICATIONS:
"H"
Horizontal center line of headlights
from ground.
: 26.8 in.(656 mm)
"W"
Distance between each headlight
center.
: 43.3 in. (1,100 mm)
"L"
Distance between the headlights
and the wall that the lights are tested
against.
: 118 in. (3,000 mm). G270A01TB-EAT
REPLACING LIGHT BULBS
Headlight Bulb
In the event of bulb failure being expe-
rienced, ensure that the relative lighting
circuit is turned off prior to attempting to
replace the bulb. The illustrations on
the following page will assist in locating
and removing the various bulbs. En-
sure that the replacement bulb has the
same cap configuration and wattage as
the original.
!
CAUTION:
Keep the lamps out of contact with
petroleum product, such as oil, gaso-
line, etc.
If the vehicle has had front body repair
and the headlight assembly has been
replaced, the headlight aiming should
be checked using the aiming screen as
shown in the illustration. Turn on the
headlight switch. (Low Beam Position)
1. Adjust headlights so that main axis
of light is parallel to center line of the
body and is aligned with point "P"
shown in the illustration.
2. Dotted lines in the illustration show
the center of headlights.
G290B01TB-EAT
Adjustment After Headlight As-
sembly ReplacementG290B01L
L
W
H
H Cut-off line
Ground
line
"P"
Horizontal line0.59in. (15mm)
1.18 in. (30mm) Vertical line
tbuk-6.p65
3/23/04, 4:27 PM
28

10- 2 INDEX
A
AIR BAG ................................................... ................1-30
AIR CONDITIONING SWI TCH ................................. 1-74
AIR CONDITIONING SYSTEM MAINTENANCE .....6-19
AIR CLEANER FILTER ............................................. 6-14
ANTENNA ................................................... ..............1-84
ANTI-LOCK BRAKE SYSTEM .................................. 2-13
ANTI-THEFT ALARM SYSTEM .................................. 1-7
ASHTRAY ................................................... ..............1-54
AUTO FUEL CUT SWITCH...................................... 1-68
AUTOMATIC TRANSAXLE ......................................... 2-9
AUTOMATIC TRANSAXLE FLUID .......................... .6-16
B
BATTERY MAINTENANCE ......................................6-25
BEFORE STARTING THE ENGINE........................... 2-3
BONNET RELEASE .................................................. 1-62
BRAKE PEDAL FREEPLAY ..................................... 6-22
BRAKE SYSTEM CHECKI NG ..................................6-18
C
CARE OF DI SC ................................................. ........1-82
CARE OF SEAT BELTS ........................................... 1-19
CARGO AREA COVER ............................................ 1-66
CATALYTIC CONVERTOR OPERATING PRECAUTIONS ................................................... ... 7-3
CENTRAL DOOR LOCKS .......................................... 1-5
CHANGING A FLAT TYRE ......................................... 3-6 CHILD-PROOF REAR DOOR LOCK
.......................... 1-5
CHILD RESTRAINT SYST EM ..................................1-22
CIGAR LIGHTER ................................................... ...1-53
CLUTCH PEDAL FREEPLAY ...................................6-22
COMBINATION IGNITION SWITCH AND STEERING LOCK ................................................... 2-3
CONSOLE TRAY ................................................... ...1-54
COOLANT TEMPERATURE GAUGE .......................1-44
D
DAILY OPERATING CHECKS .................................... 6-6
DIGITAL CLOCK ........ ............................................... 1-53
DOOR LOCKS ................................................... ......... 1-5
DOOR WINDOWS ................................................... .1-10
DRINK HOLDER ... ................................................... .1-54
DRIVE BELTS ................................................... ........6-23
DRIVING FOR ECONOMY .......................................2-14
E
EFFECTIVE BRAKING ............................................. 2-13
ELECTRIC COOLING FANS ....................................6-25
EMERGENCY TOWI NG ........................................... 3-12
EMISSION CONTROL SYSTEM ................................ 7-2
ENGINE COM PARTMENT......................................... 6-2
ENGINE COOLANT CHECKING AND REPLACI NG ................................................. ........6-10
ENGINE OIL AND FILTER REPLACEMENT .............. 6-9
ENGINE OIL CO NSUMPTION................................... 6-8
tbuk-10.p65 3/23/04, 4:31 PM
2