2004 Hyundai Coupe ignition

FEATURES OF YOUR HYUNDAI
1- 22
A fully inflated airbag in combination with a prop- erly worn seat belt slows the driver's or thepassenger's forward motion, thus reducing therisk of head and chest injury.After complete inflation, the airbag immediatelystarts deflating, enabling the driver to maintainforward visibility.
Passanger's Airbag
B240B01GK
FUA1115A
CAUTION: When installing a container of liquid air fresh-ener inside a vehicle, do not place it near theinstrument cluster nor on the instrument panelpad surface. If there is any leakage from theair freshener onto these areas (instrumentcluster, instrument panel pad or air ventila-tor), it may damage these parts. If the liquidfrom the air freshener does leak onto theseareas, wash them with water immediately.
B240B03L
o The SRS can function only when the igni- tion key is in the "ON" position. If the SRS SRI does not come on or illuminatescontinuously when the ignition key isturned to "ON", or continuously remainson after flashing for about 6 seconds whenthe ignition key is turned to the "ON"position, or after the engine is started,comes on while driving, the SRS is notworking properly. If this occurs, have yourvehicle immediately inspected by yourHyundai dealer.
o Before you replace a fuse or disconnect a battery terminal, turn the ignition key tothe "LOCK" position or remove the igni-tion key. Never remove or replace the airbag related fuse(s) when the ignition keyis in the "ON" position. Failure to heed thiswarning will cause the SRS SRI to illumi-nate.
WARNING:
o When the SRS is activated, there may be a loud noise and fine dust will be releasedthroughout the vehicle. These conditionsare normal and are not hazardous. How-ever, the fine dust generated during airbagdeployment may cause skin irritation.Wash your hands and face thoroughlywith lukewarm water and a mild soap afteran accident in which the airbags weredeployed.

FEATURES OF YOUR HYUNDAI 1- 23
WARNING:
o The side impact airbag is supplemental to
the driver's and the passenger's seat beltsystems and is not a substitute for them.Therefore your seat belts must be worn atall times while the vehicle is in motion. Theairbags deploy only in certain side impactconditions severe enough to cause sig-nificant injury to the vehicle occupants.
o For best protection from the side impact airbag system and to avoid being injuredby the deploying side impact airbag, bothfront seat occupants should sit in an up-right position with the seat belt properlyfastened. The driver's hands should beplaced on the steering wheel at the 9:00and 3:00 o'clock positions. Thepassenger's arms and hands should beplaced on their laps.
o Do not use any accessory seat covers.
o Use of seat covers could prevent or re- duce the effectiveness of the system.
o Do not install any accessories on the side or near the side impact airbag.
o Do not use excessive force on the side of the seat.
o Do not place any objects over the airbag or between the airbag and yourself.
o Do not place any objects (an umbrella, bag, etc.) between the front door and thefront seat. Such objects may become dan-gerous projectiles and cause injury if thesupplemental side impact airbag inflates.
Your Hyundai is equipped with a side impactairbag in each front seat. The purpose of theairbag is to provide the vehicle's driver and/or thefront passenger with additional protection thanthat offered by the seat belt alone. The sideimpact airbags are designed to deploy only dur-ing certain side-impact collisions, depending onthe crash severity, angle, speed and point ofimpact. The side impact airbags are not de-signed to deploy in all side impact situations.
B990B04Y-AAT Side Impact Airbag
B990B02Y
o To prevent unexpected deployment of the
side impact airbag that may result in per- sonal injury,avoid impact to the side airbagsensor when the ignition key is on.
B240C02Y-GAT SRS Care The SRS is virtually maintenance-free and there are no parts you can safely service by yourself.The entire SRS system must be inspected by anauthorized Hyundai dealer 10 years after thedate that the vehicle was manufactured. Any work on the SRS system, such as removing, installing, repairing, or any work on the steeringwheel must be performed by a qualified Hyundaitechnician. Improper handling of the SRS sys-tem may result in serious personal injury.
YT10355A

FEATURES OF YOUR HYUNDAI 1- 27
B260B01GK-GAT
SRS (Airbag) Service Reminder Indicator (SRI)
The SRS service reminder indicator (SRI) comes on and flashes for about 6 seconds after theignition key is turned to the "ON" position or afterthe engine is started, after which it will go out. This light also comes on when the SRS is not working properly. If the SRI does not come on orilluminates continuously when the ignition key isturned to "ON", or continuously remains on afterflashing for about 6 seconds when you turned theignition key to the "ON" position or started theengine, or if it comes on while driving, have theSRS inspected by an authorized Hyundai Dealer. B260P02Y-GAT
ABS Service Reminder Indicator (SRI)(If installed)
When the key is turned to the "ON" position, the Anti-Lock Brake System will come on and thengo off in a few seconds. If the ABS SRI remainson, comes on while driving, or does not come onwhen the key is turned to the "ON" position, thisindicates that there may be a problem with theABS.If this occurs, have your vehicle checked by yourHyundai dealer as soon as possible. The normalbraking system will still be operational, but with-out the assistance of the anti-lock brake system. B260F01A-AAT
High Beam Indicator Light
The high beam indicator light comes on when-ever the headlights are switched to the highbeam or flash position.
B260D01A-AAT
Turn Signal Indicator Lights
The blinking green arrows on the instrumentpanel show the direction indicated by the turnsignals. If the arrow comes on but does not blink,blinks more rapidly than normal, or does notilluminate at all, a malfunction in the turn signalsystem is indicated. Your dealer should be con-sulted for repairs. B260G01A-AAT
Low Oil Pressure Warning Light
CAUTION:If the oil pressure warning light stays onwhile the engine is running, serious enginedamage may result. The oil pressure warninglight comes on whenever there is insufficientoil pressure. In normal operation, it shouldcome on when the ignition switch is turnedon, then go out when the engine is started. Ifthe oil pressure warning light stays on whilethe engine is running, there may be a seriousmalfunction.If this happens, stop the car as soon as it issafe to do so, turn off the engine and checkthe oil level. If the oil level is low, fill the engineoil to the proper level and start the engineagain. If the light stays on with the enginerunning, turn the engine off immediately. Inany instance where the oil light stays onwhen the engine is running, the engine shouldbe checked by an authorized Hyundai dealerbefore the car is driven again.
WARNING:If the both ABS SRI and Parking Brake/Brakefluid level warning lights remain "ON" orcome on while driving, there may be a prob-
lem with E.B.D (Electronic Brake Force Dis-tribution).If this occurs, avoid sudden stops and haveyour vehicle checked by your Hyundai dealeras soon as possible.
AIR
BAG

FEATURES OF YOUR HYUNDAI
1- 28
B260J01S-GAT Charging System Warning Light
The charging system warning light should come on when the ignition is turned on, then go outwhen the engine is running. If the light stays onwhile the engine is running, there is a malfunctionin the electrical charging system. If the lightcomes on while you are driving, stop, turn off theengine and check under the hood. First, makecertain the generator drive belt is in place. If it is,check the tension of the belt.And then, have the system checked by yourHyundai dealer. CAUTION: If the drive belt (generator belt) is loose,broken, or mission while the vehicle is driv-ing, there may be a serious malfunction, en-gine could overheat because this belt alsodrives the water pump. B260L01A-GAT
Door Ajar Warning Light
The door ajar warning light warns you that a dooris not completely closed.
B260H01GK-AAT Parking Brake/Low Brake Fluid Level Warning Light
CAUTION: If you suspect brake trouble, have your brakeschecked by a Hyundai dealer as soon aspossible. Driving your car with a problem ineither the brake electrical system or brakehydraulic system is dangerous, and couldresult in a serious injury or death. Warning Light Operation The parking brake/brake fluid level warning light should come on when the parking brake is ap-plied and the ignition switch is turned to "ON" or"START". After the engine is started, the lightshould go out in three seconds.If the parking brake is not applied, the warninglight should come on when the ignition switch isturned to "ON" or "START", then go out in threeseconds. If the light comes on at any other time,you should slow the vehicle and bring it to acomplete stop in a safe location off the roadway.The brake fluid level warning light indicates thatthe brake fluid level in the brake master cylinderis low and hydraulic brake fluid conforming toDOT 3 or DOT 4 specifications should be added.After adding fluid, if no other trouble is found, thecar should be immediately and carefully driven toa Hyundai dealer for inspection. If further troubleis experienced, the vehicle should not be drivenat all but taken to a dealer by a professionaltowing service or some other safe method. Your Hyundai is equipped with dual-diagonalbraking systems. This means you still have brak-ing on two wheels even if one of the dual systemsshould fail. With only one of the dual systemsworking, more than normal pedal travel andgreater pedal pressure are required to stop thecar. Also, the car will not stop in as short adistance with only half of the brake system work-ing. If the brakes fail while you are driving, shift toa lower gear for additional engine braking andstop the car as soon as it is safe to do so.
B260M01A-AAT
Low Fuel Level Warning Light
The low fuel level warning light comes on when the fuel tank is approaching empty. When itcomes on, you should add fuel as soon aspossible. Driving with the fuel level warning lighton or with the fuel level below "E" can cause theengine to misfire and damage the catalytic con-verter.
B260K01F-AAT Tail Gate Open Warning Light
This light remains on unless the tail gate is completely closed and latched.
B265C01O-AAT Traction Control Indicator Lights (If installed)
The traction control indicators change operation according to the ignition switch position andwhether the system is in operation or not.They will illuminate when the ignition key isturned to the "ON" position, but should go outafter three seconds. If the TCS or TCS-OFF

FEATURES OF YOUR HYUNDAI 1- 29
B280A01A-AAT FUEL GAUGE The needle on the gauge indicates the approxi- mate fuel level in the fuel tank. The fuel capacityis given in Section 9. B290A02A-AAT ENGINE COOLANT TEMPERATURE GAUGE
B270A01A-AATBRAKE PAD WEAR WARNING SOUNDThe front disc brake pads have wear indicators
that should make a high-pitched squealing orscraping noise when new pads are needed. The
sound may come and go or be heard all the time
when the vehicle is moving. It may also be heardwhen the brake pedal is pushed down firmly.
Excessive rotor damage will result if the wornpads are not replaced. See your Hyundai dealerimmediately.
HGK133
HGK132
B260N01GK-AAT
Malfunction Indicator Light (If installed)
This light illuminates when there is a malfunction of an exhaust gas related component, and thesystem is not functioning properly so that theexhaust gas regulation values are not satisfied.This light will also illuminate when the ignition keyis turned to the "ON" position, and will go out afterengine starting. If it illuminates while driving, ordoes not illuminate when the ignition key isturned to the "ON" position, take your car to yournearest authorized Hyundai dealer and have thesystem checked.
B260E01HP-GAT Seat Belt Warning Light (If Installed)
The seat belt warning light blinks for about 6 seconds when the ignition key is turned from the"OFF" position to "ON" or "START".
B260Q01E-GAT
Cruise Indicator (If Installed)
The cruise indicator light in the instrument cluster is illuminated when the cruise control main switchon the end of the barrel is pushed.The indicator light does not illuminate when thecruise control main switch is pushed a secondtime.Information about the use of cruise control isbeginning on page 1-46.indicator stays on, take your car to your autho- rized Hyundai dealer and have the systemchecked. See section 2 for more informationabout the TCS.

FEATURES OF YOUR HYUNDAI
1- 30 B330A02A-AAT TACHOMETER
HGK131A
The tachometer registers the speed of your en- gine in revolutions per minute (rpm). CAUTION: The engine should not be raced to such aspeed that the needle enters the red zone onthe tachometer face. This can cause severeengine damage and may void your warranty.
WARNING:Never remove the radiator cap when the en-gine is hot. The engine coolant is under pres-sure and could erupt and cause severe burns.Wait until the engine is cool before removingthe radiator cap. The needle on the engine coolant temperature gauge should stay in the normal range. If itmoves across the dial to "H" (Hot), pull over andstop as soon as possible and turn off the engine.Then open the hood and, after the engine hascooled, check the coolant level and the waterpump drive belt. If you suspect cooling systemtrouble, have your cooling system checked by aHyundai dealer as soon as possible. B300A01A-GAT SPEEDOMETER Your Hyundai's speedometer is calibrated in kilometers per hour or miles per hour.
HGK130A
B310B01GK-GAT ODOMETER/TRIP ODOMETER
HGK028A
Function of digital odometer/trip odom- eter
Pushing in the reset switch on the right side of speedometer when the ignition switch is turned"ON" will display the following sequence:
HGK055A
132

FEATURES OF YOUR HYUNDAI 1- 33
To operate the headlights, turn the barrel on the end of the multi-function switch. The first positionturns on the parking lights, sidelights, tail lightsand instrument panel lights. The second positionturns on the headlights. NOTE: The ignition must be in the "ON" position toturn on the headlights. Parking light auto cut (If installed) If you do not turn the parking lights "OFF" after driving, the parking lights will automatically shut"OFF" when the driver's door is opened.To turn them "ON" again, you must simply turnthe ignition key to the "ON" position.
Instantaneous Fuel Consumption gauge It shows instantaneous fuel consumption ac- cording to the driving condition. The more indi-cated figure is low, the more it indicates efficientdriving situation. Volt gauge It shows moment volt change and makes for diver correspond to low volt situation.
HGK231B340B01A-AAT Lane Change Signal
To indicate a lane change, move the lever up or down to a point where it begins flashing.
B340C03E-AAT Headlight Switch
HGK038 HGK039
B340A01A-AAT COMBINATION TURN SIGNAL, HEADLIGHT AND HIGH-BEAMSWITCH Turn Signal Operation Pulling down on the lever causes the turn signals on the left side of the car to blink. Pushingupwards on the lever causes the turn signals onthe right side of the car to blink. As the turn iscompleted, the lever will automatically return tothe center position and turn off the turn signals atthe same time. If either turn signal indicator lightblinks more rapidly than usual, goes on but doesnot blink, or does not go on at all, there is amalfunction in the system. Check for a burned-out fuse or bulb or see your Hyundai dealer.
The lever will automatically return to the center position when released.

FEATURES OF YOUR HYUNDAI
1- 36
B370A01A-AAT HAZARD WARNING SYSTEM The hazard warning system should be used whenever you find it necessary to stop the car ina hazardous location. When you must makesuch an emergency stop, always pull off the roadas far as possible.The hazard warning lights are turned on bypushing in the hazard switch. This causes all turnsignal lights to blink. The hazard warning lightswill operate even though the key is not in theignition.To turn the hazard warning lights off, push theswitch a second time.
HGK140 B380A01A-AAT REAR WINDOW DEFROSTER SWITCH The rear window defroster and heated outsides rearview mirrors are turned on by pushing in theswitch. To turn the defroster off, push the switcha second time. The rear window defroster auto-matically turns itself off after about 15 minutes.To restart the defroster cycle, push in the switchagain after it has turned itself off. CAUTION: Do not clean the inner side of the rear windowglass with an abrasive type of glass cleaneror use a scraper to remove foreign depositsfrom the inner surface of the glass as thismay cause damage to the defroster elements. NOTE: The ignition must be in the "ON" position forthe rear window defroster to operate. B400A01A-AAT DIGITAL CLOCK (If Installed) There are three control buttons for the digital clock. Their functions are: HOUR
- Push "H" to advance the hour indicated.
MIN - Push "M" to advance the minute indicated.
RESET - Push "R" to reset minutes to ":00" to
facilitate resetting the clock to the correct time. When this is done: Pressing "R" between 10 : 30 and 11 : 29 changes the readout to 11 : 00. Pressing "R" between 11: 30 and 12 : 29 changes the readout to 12 : 00.
B380A01GK
A Type
B TypeHGK143
A Type
B Type