2004 DAEWOO NUBIRA automatic transaxle

POWER STEERING GEAR 6C – 13
DAEWOO V–121 BL4
2. Install the bolts and nuts on the steering gear
mounting bracket.
Tighten
Tighten the steering gear mounting bracket bolts and
nuts to 60 NSm (44 lb–ft).
3. Install the return line into the clip on the crossmem-
ber.
Tighten
Tightem the return line clip bolt to 8 NSm (71 lb–in).
4. On vehicles equipped with a manual transaxle,
position the transaxle center bracket in place and
install the bolts securing the bracket to the engine
and the transaxle.
Tighten
Tighten the transaxle center bracket–to–transaxle
bolts and the transaxle center bracket–to–engine bolt
to 80 NSm (59 lb–ft).
5. On vehicles equipped with an automatic transaxle,
install the transaxle center bracket. Refer to Section
5A, Automatic Transaxle.
6. Install the crossmember. Refer to Section 2C, Front
Suspension.
7. Connect the tie rod ends to the strut assembly.
8. Install the outer tie rod nuts.
Tighten
Tighten the outer tie rod nuts to 50 NSm (37 lb–ft).

9B – 26ILIGHTING SYSTEMS
DAEWOO V–121 BL4
Backup Lamps Inoperative
StepActionValue(s)YesNo
11. Block the wheels.
2. Apply the parking brake to prevent the vehicle
from moving.
3. Turn the ignition on.
4. Put the transaxle in reverse (R).
5. Remove one of the backup lamps from its
socket.
6. Test the lamp socket positive terminal with a
voltmeter.
Does the battery voltage available at the backup
lamp socket positive terminal equal the specified
value?11–14 vGo to Step 3Go to Step 2
2Repair the open circuit between fuse F20 and the
backup lamps.
Is the repair complete?–System OK–
3Connect an ohmmeter between ground and the neg-
ative terminal at the bulb socket.
Is the resistance equal to the specified value?0 WGo to Step 4Go to Step 5
4Replace the faulty backup lamps.
Is the repair complete?–System OK–
51. Reinstall the backup lamps.
2. Disconnect the electrical connector at the re-
verse switch. (On automatic transaxle (A/T)
vehicles, disconnect the neutral safety/backup
switch.)
3. Turn the ignition on.
4. Put the transaxle in R.
5. Use a voltmeter to check for the reverse switch
terminal 1. (On A/T vehicles, test terminal 7 of
the neutral safety/backup switch).
Does the battery voltage available at terminal 1 (or
terminal 7, if equipped with A/T) equal the specified
value?11–14 vGo to Step 7Go to Step 6
6Repair the open circuit between the backup lamps
and the, reverse switch (or the neutral safety/backup
switch if equipped with A/T).
Is the repair complete?–System OK–
71. Put the transaxle in R.
2. Use an ohmmeter to check the continuity be-
tween reverse switch terminal 1 and terminal 2
(terminals 7 and 8 on the neutral safety/backup
switch, if equipped with A/T).
Does the continuity between terminals 1 and 2 (ter-
minals 7 and 8, if equipped with A/T) equal the speci-
fied value?0 WGo to Step 9Go to Step 8

LITHING SYSTEMS 9B – 47
DAEWOO V–121 BL4
BACKUP LAMPS
The backup lamps are located in the rear combination
lamps They will come on when the transaxle is shifted into
reverse. On a vehicle with an automatic transaxle, the
backup lamps are activated by the neutral safety backup
(NSBU) switch. On a vehicle with a manual transaxle, they
are activated by a reverse switch which is part of the trans-
axle.