2004 DAEWOO NUBIRA battery

GENERAL INFORMATION 0B – 5
DAEWOO V–121 BL4
Cooling System
Application1.4L DOHC1.6L DOHC1.8L DOHC
Cooling TypeForced Water
Circulation


Radiator TypeCross–flow


Water Pump TypeCentrifugal


Thermostat TypePellet Type


Coolant Capacity7.0L (7.49 qts)7.2L (7.6 qts)7.4L (7.8 qts)
Electric System
Application1.4L DOHC1.6L DOHC1.8L DOHC
Battery12V–55 AH


610 CCA
(Cold Cranking Amps)


Alternator85 Amps
95 Amps
Starter1.2 KW
1.4 KW
No–Load Test @ 12.2
volts
Drive Pinion Speed at :90 Amps Max
Min. 2,600 rpm


85 Amps Max
Min. 2,550 rpm

GENERAL INFORMATION 0B – 15
DAEWOO V–121 BL4
GENERAL DESCRIPTION
AND SYSTEM OPERATION
GENERAL REPAIR INSTRUCTIONS
S If a floor jack is used, the following precautions are
recommended.
S Park the vehicle on level ground,
block" the front
or rear wheels, set the jack against the frame, raise
the vehicle and support it with chassis stands and
then perform the service operation.
S Before performing the service operation, disconnect
the negative battery cable in order to reduce the
chance of cable damage and burning due to short–
circuiting.
S Use a cover on the body, the seats and the floor to
protect them against damage and contamination.
S Handle brake fluid and antifreeze solution with care
as they can cause paint damage.
S The use of proper tools, and the recommended es-
sential and available tools where specified, are im-
portant for efficient and reliable performance of the
service repairs.S Use genuine DAEWOO parts.
S Discard used cotter pins, gaskets, O–rings, oil
seals, lock washers and self–locking nuts. Prepare
new ones for installation. Normal function of these
parts cannot be maintained if these parts are re-
used.
S Keep the disassembled parts neatly in groups to
facilitate proper and smooth reassembly.
S Keep attaching bolts and nuts separated, as they
vary in hardness and design depending on the posi-
tion of the installation.
S Clean the parts before inspection or reassembly.
S Also clean the oil parts, etc. Use compressed air to
make certain they are free of restrictions.
S Lubricate rotating and sliding faces of parts with oil
or grease before installation.
S When necessary, use a sealer on gaskets to pre-
vent leakage.
S Carefully observe all specifications for bolt and nut
torques.
S When service operation is completed, make a final
check to be sure service was done properly and the
problem was corrected.

HOW TO USE ELECTRICAL WIRING DIAGRAMW1–3
2. CIRCUIT IDENTIFICATION SYMBOL
IDENTIFICATION
SYMBOLMEANING
CConnector
DDiode
EfFuse in engine room fuse box
FFuse in passenger room fuse box
GGround
SSplice pack(Junction connector)
3. FUNCTION OF POWER SUPPLY LINE (NUMBER)
Power supply NoPower supply condition
15Battery Voltage(B+) supply in Ignition Switch ”ON” and ”ST” (IGN 1)
15ABattery Voltage(B+) supply in Ignition Switch ”ON” (IGN 2)
15CBattery Voltage(B+) supply in Ignition Switch ”ON” and ”ACC”
30Battery Voltage(B+) supply directly regardless of Ignition Switch
31Ground connected to battery(
)
58Battery Voltage(B+) supply in Head Lamp Switch 1st and 2nd step (Illumination circuit)
4. WIRING HARNESS COLOR IDENTIFICATION
AbbreviationColorAbbreviationColor
BrBrownSbSky Blue
GGreenRRed
VVioletLBlue
PPinkYYellow
WWhiteGrGray
OrOrangeBBlack
LgLight Green
5. HOW TO CHECK TERMINAL NUMBER OF CONNECTOR
" Terminal number is given based on Female Terminal Connectorex) Terminal Number 4 of C901 connection

SECTION : 1A
GENERAL ENGINE INFORMATION
TABLE OF CONTENTS
DIAGNOSIS1A–1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compression Test 1A–1. . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pressure Test 1A–2. . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Leak Diagnosis 1A–3. . . . . . . . . . . . . . . . . . . . . . . .
Knock Diagnosis 1A–4. . . . . . . . . . . . . . . . . . . . . . . . . . Noise Diagnosis 1A–8. . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL INFORMATION1A–11 . . . . . . . . . . . . . . . . . .
Cleanliness and Care 1A–11. . . . . . . . . . . . . . . . . . . . .
On–Engine Service 1A–11. . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS
COMPRESSION TEST
Important : Disconnect the Crankshaft Position (CKP)
Sensor connector to disable the fuel and the ignition sys-
tems.
Test the compression pressure for each cylinder. Low
compression pressure may be the fault of the valves or the
pistons. The following conditions should be considered
when you check the cylinder compression:
S The engine should be at normal operating tempera-
ture.
S The throttle must be wide open.
S All the spark plugs should be removed.
S The battery must be at or near full charge.
1. Place approximately three squirts of oil from a
plunger– type oiler into each spark plug port.
2. Insert the engine compression gauge into each
spark plug port.
3. Crank test each cylinder with four to five compres-
sion strokes using the starter motor.4. The lowest reading should not be less than 70% of
the highest reading. The compression gauge read-
ing should not be less than 689 kPa (100 psi) for
any of the cylinders.
5. Examine the gauge readings obtained after the four
”puffs” per cylinder are obtained from cranking the
starter motor. The readings are explained in the
following descriptions:
S Normal Condition – Compression builds up quickly
and evenly to the specified compression on each
cylinder.
S Piston Rings Faulty – Compression is low on the
first stroke and tends to build up on following
strokes, but the compression pressure does not
reach normal. The compression pressure improves
considerably with the addition of oil into the cylin-
der.
S Valves Faulty – Low compression pressure on the
first stroke. The compression pressure does not
tend to build up on the following strokes. The com-
pression pressure does not improve much with the
addition of oil into the cylinder.

GENERAL ENGINE INFORMATION 1A – 11
DAEWOO V–121 BL4
GENERAL INFORMATION
CLEANLINESS AND CARE
An automobile engine is a combination of many machined,
honed, polished and lapped surfaces with tolerances that
are measured in the ten–thousandths of an inch. When
any internal engine parts are serviced, care and cleanli-
ness are important. A liberal coating of engine oil should
be applied to friction areas during assembly, to protect and
lubricate the surfaces on initial operation. Proper cleaning
and protection of machined surfaces and friction areas is
part of the repair procedure. This is considered standard
shop practice even if not specifically stated.
Whenever valve train components are removed for ser-
vice, they should be kept in order. They should be installed
in the same locations, and with the same mating surfaces,
as when they were removed.Battery cables should be disconnected before any major
work is performed on the engine. Failure to disconnect
cables may result in damage to wire harness or other elec-
trical parts.ON–ENGINE SERVICE
CAUTION : Disconnect the negative battery cable be-
fore removing or installing any electrical unit, or
when a tool or equipment could easily come in con-
tact with exposed electrical terminals. Disconnecting
this cable will help prevent personal injury and dam-
age to the vehicle. The ignition must also be in LOCK
unless otherwise noted.
Notice : Any time the air cleaner is removed, the intake
opening should be covered. This will protect against acci-
dental entrance of foreign material, which could follow the
intake passage into the cylinder and cause extensive
damage when the engine is started.

SECTION : 1C1
1.4L/1.6L DOHC ENGINE MECHANICAL
CAUTION : Disconnect the negative battery cable before removing or installing any electrical unit or when a tool
or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable will help
prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise noted.
TABLE OF CONTENTS
SPECIFICATIONS1C1–2 . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Specifications 1C1–2. . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifcations 1C1–5. . . . . . . . . .
SPECIAL TOOLS1C1–7 . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Tools Table 1C1–7. . . . . . . . . . . . . . . . . . . . . . .
COMPONENT LOCATOR1C1–9 . . . . . . . . . . . . . . . . . . .
Cylinder Head 1C1–9. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Block 1C1–10. . . . . . . . . . . . . . . . . . . . . . . . . . .
Intake & Exhaust Manifold 1C1–12. . . . . . . . . . . . . . . .
Timing Belt 1C1–13. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Mounting 1C1–14. . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE AND REPAIR1C1–15 . . . . . . . . . . . . .
ON–VEHICLE SERVICE 1C1–15. . . . . . . . . . . . . . . . . . .
Engine Cover 1C1–15. . . . . . . . . . . . . . . . . . . . . . . . . . .
Camshaft Cover 1C1–15. . . . . . . . . . . . . . . . . . . . . . . . .
Intake Manifold 1C1–16. . . . . . . . . . . . . . . . . . . . . . . . . .
Exhaust Manifold 1C1–20. . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head and Gasket 1C1–21. . . . . . . . . . . . . . . .
Camshaft 1C1–29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timing Belt Check and Adjust 1C1–30. . . . . . . . . . . . .
Timing Belt 1C1–34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oil Pan 1C1–38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pump 1C1–40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Mount 1C1–43. . . . . . . . . . . . . . . . . . . . . . . . . . .
Camshaft Gears 1C1–45. . . . . . . . . . . . . . . . . . . . . . . . .
Rear Timing Belt Cover 1C1–46. . . . . . . . . . . . . . . . . . .
Engine 1C1–48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pistons and Rods 1C1–53. . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR 1C1–58. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head and Valve Train Components 1C1–58.
Crankshaft 1C1–65. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Crankshaft Bearing and Connecting Rod
Beadings – Gauging Plastics 1C1–74. . . . . . . . . . . .
GENERAL DESCRIPTION AND SYSTEM
OPERATION1C1–77 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head and Gasket 1C1–77. . . . . . . . . . . . . . . .
Crankshaft 1C1–77. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timing Belt 1C1–77. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pump 1C1–77. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pan 1C1–77. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exhaust Manifold 1C1–77. . . . . . . . . . . . . . . . . . . . . . . .
Intake Manifold 1C1–77. . . . . . . . . . . . . . . . . . . . . . . . . .
Camshaft 1C1–77. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.4L/1.6L DOHC ENGINE MECHANICAL 1C1 – 15
DAEWOO V–121 BL4
MAINTENANCE AND REPAIR
ON–VEHICLE SERVICE
ENGINE COVER
Removal Procedure
1. Remove the bolts and nuts from the engine cover.
2. Remove the engine cover.
Installation Procedure
1. Position the engine cover on the engine.
2. Install the engine cover bolts and nuts.
Tighten
Tighten the engine cover bolts and nuts to 10 NSm(89
lb–ft).
CAMSHAFT COVER
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the engine cover. Refer to ”Engine” in this
section.
3. Remove the breather hose, ventilation hose and
cam position sensor wiring connector from the cam-
shaft cover.

1C1 – 16I1.4L/1.6L DOHC ENGINE MECHANICAL
DAEWOO V–121 BL4
4. Remove the ignition wires from the spark plug.
5. Remove the camshaft cover bolts and camshaft
cover.
6. Remove the camshaft cover gasket.
Installation Procedure
1. Install the camshaft cover gasket on the camshaft
cover.
2. Position the camshaft cover on the engine block.
3. Install the camshaft cover bolts.
Tighten
Tighten the camshaft cover bolts to 10 NSm(89 lb–ft).
4. Install the ignition wires to the spark plugs and con-
nect the breather hose, ventilation hose and cam
position sensor wiring connector to the canshaft
cover.
5. Install the engine cover.
6. Connect the negative battery cable.
INTAKE MANIFOLD
Removal Procedure
1. Remove the fuel pump fuse.
2. Start the engine. After it stalls, crank the engine for
10 seconds to rid the fuel system of fuel pressure.
3. Disconnect the negative battery calbe.
4. Drain the engine coolant. Refer to Section 1D, En-
gine Cooling.
5. Remove the engine cover and throttle body. Refer
to Section 1F, Engine Control.