2004 DAEWOO NUBIRA belt

5–164WELECTRICAL WIRING DIAGRAMS
4) WARNING (SSPS, AIR BAG, OIL PRESSURE & SEAT BELT) LAMP & HOLD MODE LAMP
CIRCUITa. CONNECTOR INFORMATION
CONNECTOR(NO.)
(PIN NO. COLOR)
CONNECTING, WIRING HARNESSCONNECTOR POSITION
C108 (24 Pin, Black)Body
EngineLeft Engine Fuse Block
C201 (76 Pin, Black)I.P
I.P Fuse BlockI.P Fuse Block
C202 (89 Pin, White)I.P
BodyLeft CO–Driver Leg Room
C206 (22 Pin, White)I.P
TCMUpper Driver Leg Room
C207 (6 Pin, White)Air Bag
I.PUpper Left Driver Leg Room
G301BodyBelow Driver Cross Member Floor Panel
b. CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION
J3B1P061

6A – 2IPOWER STEERING SYSTEM
DAEWOO V–121 BL4
DIAGNOSIS
POWER STEERING SYSTEM
PRESSURE TEST
Tools Required
KM–354–B Pressure Test Gauge Kit
Check the fluid pressure as follows to determine whether
the trouble is in the pump or the gear unit.
Test Procedure
1. Check the power steering fluid level and the power
steering pump belt tension. Refer to ”Checking and
Adding Fluid” in this section and Section 6B, Power
Steering Pump.
2. Disconnect the high pressure line at the pump. Use
a small container to catch any fluid.
3. Connect the hose of the pressure test gauge kit
KM–354–B to the power steering pressure hose
from the power steering pump.
4. Place the gear selector lever in PARK (automatic
transaxle–equipped vehicles) or NEUTRAL (manual
transaxle–equipped vehicles). Set the parking
brake.
5. Open the gauge valve fully.
6. Start the engine and let it idle.
7. Turn the steering wheel from lock to lock several
times to warm the fluid to operating temperature.
8. Increase the engine speed to 1,500 rpm.
Notice : The power steering pump could be damaged if
the valve is fully closed for more than 5 seconds.
9. Close the gauge valve fully, and read the pressure.
The pump pressure with the valve closed should be
between 8,330 kPa to 8,820 kPa (1,208 psi to
1,279 psi). With electronic variable orifice, the pres-
sure should be between 8,500 kPa to 8,960 kPa
(1,233 psi to 1,299 psi).
10. Immediately open the gauge valve fully.
11. Turn the steering wheel all the way to the left and
the right. If the pressure is within the specified lim-
its, the problem is not in the pump. Check the pow-
er steering gear for leaks.
POWER STEERING SYSTEM LEAK
TEST
General Procedure
Inspect the following:
S The fluid reservoir for overfill.
S Fluid for aeration and overflow.
S The hoses for loose connections.
S The torsion bar, stub shaft and adjuster seals for
leaks.
S The component sealing surfaces for damage.
Important : Verify the exact point of the leak. The point
from which the fluid is dripping is not necessarily the point
at which the system is leaking. When service is required,
clean the leak area upon disassembly, replace the leaking
seal, check the component sealing surfaces for damage
and reset the torque bolt to specifications, where required.
External Leak Check
The purpose of this procedure is to pinpoint the location of
the leak. In some cases, the leak can be easily located, but
seepage–type leaks may be harder to find. To locate seep-
age leaks, use the following method:
1. With the engine off, wipe dry the complete power
steering system.
2. Check the power steering fluid level in the pump’s
reservoir. Adjust the fluid level as necessary. Refer
to ”Checking and Adding Fluid” in this section.
Notice : Do not hold the steering wheel at a stop for any
length of time as this can damage the power steering
pump.
3. Start the engine. Turn the steering wheel counter-
clockwise and clockwise from stop to stop several
times.
4. Find the exact area of the leak and repair it.

SECTION : 6B
POWER STEERING PUMP
TABLE OF CONTENTS
SPECIFICATIONS6B–1 . . . . . . . . . . . . . . . . . . . . . . . . . .
General Specifications 6B–1. . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 6B–1. . . . . . . . . . .
DIAGNOSIS6B–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Steering Pump Diagnosis 6B–2. . . . . . . . . . . . .
MAINTENANCE AND REPAIR6B–3 . . . . . . . . . . . . . . .
ON–VEHICLE SERVICE 6B–3. . . . . . . . . . . . . . . . . . . . . Serpentine Accessory Drive Belt 6B–3. . . . . . . . . . . . .
Pump Assembly 6B–4. . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR 6B–7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pump 6B–7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION AND SYSTEM
OPERATION6B–8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Steering Pump 6B–8. . . . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS
GENERAL SPECIFICATIONS
ApplicationDescription
LubricantPower Steering Fluid DEXRON®–II or III
Pressure
– without EVO8330 kPa ~ 8820 kPa (1208 psi ~ 1279 psi)
– with EVO8500 kPa ~ 8960 kPa (1233 psi ~ 1299 psi)
FASTENER TIGHTENING SPECIFICATIONS
ApplicationNSmLb–FtLb–In
Air Filter Housing Assembly Bolts6–53
High–Pressure Hose Fitting2821–
Power Steering Pump Bolts2518–
Right Side Power Steering Pump Bracket Bolts3526–

6B – 2IPOWER STEERING PUMP
DAEWOO V–121 BL4
DIAGNOSIS
POWER STEERING PUMP DIAGNOSIS
Foaming or Milky Power Steering Fluid (Air in Fluid)
ChecksAction
Check for internal leakage in the power steering pump,
causing an overflow.Repair the internal pump leakage.
Bleed the system.
Check for a low fluid level.Repair the internal pump leakage.
Bleed the system.
Cold temperatures will cause the air bubbles in the system
if the fluid level is low.
Low Pressure Due to Power Steering Pump
ChecksAction
Check for an external leakage of the power steering pump
at the seals.Replace the seals.
Repair the leak.
Bleed the system.
Check for a worn serpentine accessory drive belt.Replace the serpentine accessory drive belt.
Low Pressure Due to Power Steering Gear
ChecksAction
Check for a scored housing bore.Replace the housing bore.
Check for leakage at the valve rings or the seals.Repair the leak.
Bleed the system.
Groaning Noise in the Power Steering Pump
ChecksAction
Check for air in the power steering fluid.Perform the checks listed in ”Foaming or Milky Power
Steering Fluid (Air in Fluid)” above.
Check for a low level of power steering fluid.Repair any internal or external leaks.
Bleed the system.
Check for a loose mounting of the power steering pump.Tighten the pump mounting to specifications.

POWER STEERING PUMP 6B – 3
DAEWOO V–121 BL4
MAINTENANCE AND REPAIR
ON–VEHICLE SERVICE
SERPENTINE ACCESSORY DRIVE
BELT
Removal Procedure
1. Remove the air filter housing assembly bolts and
the air intake tube.
2. Remove the air filter housing assembly from the
vehicle.
3. Use a wrench to turn the tensioner bolt clockwise,
compressing the tensioner, and releasing the ten-
sion on the serpentine accessory drive belt.
4. Remove the serpentine accessory drive belt.

6B – 4IPOWER STEERING PUMP
DAEWOO V–121 BL4
Installation Procedure
1. Use a wrench to turn the tensioner bolt clockwise,
compressing the tensioner, and releasing the ten-
sion on the serpentine accessory drive belt.
2. With the wrench in place on the tensioner bolt, loop
the serpentine accessory drive belt loosely over the
pulleys.
3. Slip the belt over the tensioner.
4. Remove the wrench from the tensioner bolt and the
belt will tighten itself.
5. Install the air filter housing assembly into the ve-
hicle.
6. Install the air intake tube and the air filter housing
assembly bolts.
Tighten
Tighten the air filter housing assembly bolts to 6 NSm
(53 lb–in).
PUMP ASSEMBLY
Removal Procedure
1. Remove the serpentine accessory drive belt. Refer
to ”Serpentine Accessory Drive Belt” in this sec-
tion.
2. Disconnect the electrical connector at the Electronc
Vaariable Orifice (EVO) solenoid actuator.

6B – 6IPOWER STEERING PUMP
DAEWOO V–121 BL4
3. Connect the supply hose to the power steering
pump.
4. Connect the high–pressure hose fitting to the power
steering pump.
Tighten
Tighten the high–pressure hose fitting to 28 NSm (21
lb–ft).
5. Connect the electrical connector at the Electronic
Variable Orifice (EVO) solenoid actuator.
6. Install the serpentine accessory drive belt. Refer to
”Serpentine Accessory Drive Belt” in this section.
7. Refill the power steering fluid. Refer to Section 6A,
Power Steering System.
8. Bleed the power steering system. Refer to Section
6A, Power Steering System.

6B – 8IPOWER STEERING PUMP
DAEWOO V–121 BL4
GENERAL DESCRIPTION
AND SYSTEM OPERATION
POWER STEERING PUMP
The power steering pump is a multivaned hydraulic pump.
The serpentine accessory drive belt on the engine drives
the power steering pump.The power steering pump provides the hydraulic pressure
to the power steering gear.
The power steering gear uses the hydraulic pressure to
assist in steering the vehicle.
The power steering system uses a remote reservoir in or-
der to make available more space in the engine compart-
ment.