2004 DAEWOO LACETTI change time

1F – 324IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1537
A/C COMPRESSOR RELAY HIGH VOLTAGE
Circuit Description
The A/C system uses an A/C refrigerant pressure sensor
mounted in the high pressure side of the A/C refrigerant
system to monitor A/C refrigerant pressure. The engine
control module (ECM) uses this information to turn ON the
engine coolant fans when the A/C refrigerant pressure is
high and to keep the compressor disengaged when A/C
refrigerant pressure is excessively high or low.
The air conditioning pressure (ACP) sensor operates like
other 3–wire sensors. The ECM applies a 5.0 volt refer-
ence and a sensor ground to the sensor. Changes in the
A/C refrigerant pressure will causes the ACP sensor input
to the ECM to vary. The ECM monitors the ACP sensor
signal circuit and can determine when the signal is out of
the possible range of the sensor. When the signal is out of
range for a prolonged period of time, the ECM will not allow
the A/C compressor clutch to engage. This is done to pro-
tect the compressor.
Conditions for Setting the DTC
S The air conditioning compressor relay circuit is a
short to battery condition exists.
Action Taken When the DTC SetsS The Malfunction Indicator Lamp (MIL) will not illumi-
nate.
S The ECM will store conditions which were present
when the DTC was set as Failure Records data
only.
S This information will not be stored in the Freeze
Frame data.
Conditions for Clearing the MIL/DTC
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Inspect harness connectors for backed–out terminals, im-
proper mating, broken locks, improperly formed or dam-
aged terminals, and poor terminal–to–wire connection at
the ECM.
Inspect the wiring harness for damage. If the harness ap-
pears to be OK, observe the A/C pressure display on the
scan tool while moving the connectors and wiring har-
nesses related to the ACP sensor. A change in the A/C
pressure display will indicate the location of the fault.

1F – 326IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1538
A/C COMPRESSOR RELAY LOW VOLTAGE
Circuit Description
The A/C system uses an A/C refrigerant pressure sensor
mounted in the high pressure side of the A/C refrigerant
system to monitor A/C refrigerant pressure. The engine
control module (ECM) uses this information to turn ON the
engine coolant fans when the A/C refrigerant pressure is
high and to keep the compressor disengaged when A/C
refrigerant pressure is excessively high or low.
The air conditioning pressure (ACP) sensor operates like
other 3–wire sensors. The ECM applies a 5.0 volt refer-
ence and a sensor ground to the sensor. Changes in the
A/C refrigerant pressure will causes the ACP sensor input
to the ECM to vary. The ECM monitors the ACP sensor
signal circuit and can determine when the signal is out of
the possible range of the sensor. When the signal is out of
range for a prolonged period of time, the ECM will not allow
the A/C compressor clutch to engage. This is done to pro-
tect the compressor.
Conditions for Setting the DTC
S The air conditioning compressor relay circuit is a
short to ground an open condition exists.
Action Taken When the DTC SetsS The Malfunction Indicator Lamp (MIL) will not illumi-
nate.
S The ECM will store conditions which were present
when the DTC was set as Failure Records data
only.
S This information will not be stored in the Freeze
Frame data.
Conditions for Clearing the MIL/DTC
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Inspect harness connectors for backed–out terminals, im-
proper mating, broken locks, improperly formed or dam-
aged terminals, and poor terminal–to–wire connection at
the ECM.
Inspect the wiring harness for damage. If the harness ap-
pears to be OK, observe the A/C pressure display on the
scan tool while moving the connectors and wiring har-
nesses related to the ACP sensor. A change in the A/C
pressure display will indicate the location of the fault.

1F – 330IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1610
MAIN RELAY HIGH VOLTAGE (1.6L DOHC)
Circuit Description
When the ignition switch to ON, main relay will grounded
to ECM internal ground by ECM controlling.
A system voltage Diagnostic Trouble Code (DTC) will set
whenever the voltage is below a calibrated value.
Conditions for Setting the DTC
S The main relay circuit is a short to battery condition
exists.
Action Taken When the DTCs Sets
S The Malfunction Indicator Lamp (MIL) will illumi-
nate.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using the scan tool can clear DTC(s).
S Disconnecting the ECM battery feed for 10 sec-
onds.
Diagnostic Aids
Inspect harness connectors for backed–out terminals, im-
proper mating, broken locks, improperly formed or dam-
aged terminals, and poor terminal–to–wire connection at
the ECM.
Inspect the wiring harness for damage. If the harness ap-
pears to be OK, observe the A/C pressure display on the
scan tool while moving the connectors and wiring har-
nesses related to the ACP sensor. A change in the A/C
pressure display will indicate the location of the fault.
If DTC P1610 cannot be duplicated, reviewing the Fail Re-
cords vehicle mileage since the diagnostic test last failed
may help determine how often the condition that caused
the DTC to set occurs. This may assist in diagnosing the
condition.

1F – 334IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1611
MAIN RELAY LOW VOLTAGE (1.6L DOHC)
Circuit Description
When the ignition switch to ON, main relay will grounded
to ECM internal ground by ECM controlling.
A system voltage Diagnostic Trouble Code (DTC) will set
whenever the voltage is below a calibrated value.
Conditions for Setting the DTC
S The main relay circuit is a short to ground or an
open condition exists.
Action Taken When the DTCs Sets
S The Malfunction Indicator Lamp (MIL) will illumi-
nate.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using the scan tool can clear DTC(s).
S Disconnecting the ECM battery feed for 10 sec-
onds.
Diagnostic Aids
Inspect harness connectors for backed–out terminals, im-
proper mating, broken locks, improperly formed or dam-
aged terminals, and poor terminal–to–wire connection at
the ECM.
Inspect the wiring harness for damage. If the harness ap-
pears to be OK, observe the A/C pressure display on the
scan tool while moving the connectors and wiring har-
nesses related to the ACP sensor. A change in the A/C
pressure display will indicate the location of the fault.
If DTC P1611 cannot be duplicated, reviewing the Fail Re-
cords vehicle mileage since the diagnostic test last failed
may help determine how often the condition that caused
the DTC to set occurs. This may assist in diagnosing the
condition.

ENGINE CONTROLS 1F – 347
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0106
MANIFOLD ABSOLUTE PRESSURE RATIONALITY
Circuit Description
The Engine Control Module (ECM) uses the Manifold Ab-
solute Pressure (MAP) sensor to control the fuel delivery
and the ignition timing. The MAP sensor measures the
changes in the intake manifold pressure which results
from engine load (intake manifold vacuum) and the rpm
changes, and it converts these into voltage outputs. The
ECM can detect if the MAP sensor is not responding to the
Throttle Position (TP) changes by comparing the actual
MAP change to a predicted MAP change based on the
amount of TP change that occurs. If the ECM does not see
the expected MAP change or more, DTC P0106 will set.
Conditions for Setting the DTC
S Altitude compensated MAP reading is higher than
high threshold or lower than low threshold table
based on rpm and TP signal.
S DTCs P0107, P0108, P0117, P0118, P0122,
P0123, P0201, P0202, P0203, P0204, P0300,
P0351, P0352, P0402, P0404, P1404, P0405,
P0406, P0506, P0507 are not set.
S Engine running.
S Valid Barometric Pressure (BARO) update.
S Torque Converter Clutch (TCC) steady (A/T).
S A/C steady state.
S No TP sensor fail conditions present.
S No MAP fail conditions present.
S Change in Idle Air Control (IAC) is less than 5%.
S Coolant temperature is greater than –10°C (14°F).
S Change in rpm is less than 200.
S Change in TP sensor is less than 3%.
S Change in Exhaust Gas Recirculation (EGR) value
is less than 6%.
S The rpm is between 1300 and 4500.
S All of the above are stabilized for 1.5 seconds.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive ignition cycle with a fail.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
S The ECM will substitute a fixed MAP value and use
TP sensor to control the fuel delivery. (The scan
tool will not show defaulted value.)
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.Diagnostic Aids
With the ignition ON and the engine stopped, the manifold
pressure is equal to atmospheric pressure and the signal
voltage will be high. This information is used by the ECM
as an indication of vehicle altitude. Comparison of this
reading with a known good vehicle with the same sensor
is a good way to check the accuracy of a suspect sensor.
Readings should be the same +0.4 volt.
The MAP sensor vacuum source should be thoroughly
checked for restrictions at the intake manifold.
Test Description
Numbers below refer to the step numbers on the Diagnos-
tic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the occurred. The information is then stored on the
scan tool for later reference.
2. A sensor that displays an ignition ON, engine OFF
BARO value that does not appear normal for the
altitude the vehicle is in should be considered to be
malfunctioning.
3. While starting the engine, the MAP sensor should
detect any changes in the manifold pressure. This
test is to determine if the sensor is stuck at a value.
4. A normal MAP sensor will react as quickly to the
throttle changes as they can be made. A sensor
should not appear to be lazy or catch up with the
throttle movements.
5. This step checks if the reason for no MAP change
was due to a faulty sensor or vacuum source to the
sensor.
6. The MAP sensor vacuum source should be thor-
oughly checked for restrictions. A drill bit can be
used to clean out any casting flash that may exist in
the vacuum port.
7. The MAP sensor vacuum source should be thor-
oughly checked for restrictions. A drill bit can be
used to clean out any casting flash that may exist in
the vacuum port.
9. The MAP Sensor System Performance diagnostic
may have to complete several tests before deter-
mining if the diagnostic has passed or failed the last
test. Operate the vehicle in the Conditions for Set-
ting the DTC several times to ensure that the diag-
nostic runs enough tests to pass or fail.
10. If no faults have been found at this point and no
additional DTCs were set, refer to ”Diagnostic
Aids”in this section for additional checks and infor-
mation.

ENGINE CONTROLS 1F – 349
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0107
MANIFOLD ABSOLUTE PRESSURE LOW VOLTAGE
Circuit Description
The Engine Control Module (ECM) uses the Manifold Ab-
solute Pressure (MAP) sensor to control the fuel delivery
and the ignition timing. The MAP sensor measures the
changes in the intake manifold pressure which results
from engine load (intake manifold vacuum) and the rpm
changes, and it converts these into voltage outputs. The
ECM sends a 5 volt reference voltage to the MAP sensor.
As the manifold pressure changes, the output of MAP sen-
sor also changes. By monitoring the Map sensor output
voltage, the ECM knows the manifold pressure. A low
pressure (low voltage) output voltage will be about 1.0 to
1.5 volts while the higher pressure (high voltage) output
voltage will be about 4.5 to 4.8 volts at Wide Open
Throttle(WOT). The MAP sensor is also used, under cer-
tain conditions to measure Barometric Pressure (BARO),
allowing the ECM to make adjustments for different alti-
tude.
Conditions for Setting the DTC
S MAP is less than 12 kPa (1.7 psi)
S No TP sensor fail conditions present.
S TP sensor is greater than 0% if the rpm is less than
1000.
S TP sensor is greater than 5% if the rpm is greater
than 1000.
S System voltage is between 11.0 and 11.5 volts.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illumi-
nate.S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
S The ECM will substitute a fixed MAP value and use
TP sensor to control the fuel delivery. (The scan
tool will not show defaulted value.)
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
With the ignition ON and the engine stopped, the manifold
pressure is equal to atmospheric pressure and the signal
voltage will be high. This information is used by the ECM
as an indication of vehicle altitude. Comparison of this
reading with a known good vehicle with the same sensor
is a good way to check the accuracy of a suspect sensor.
Readings should be the same 12 kPa.
If a DTC P0107 is intermittent, refer to ”Manifold Absolute
Pressure Check” in this section for further diagnosis.
Important : After repairs, use the scan tool FUEL TRIM
RESET function to reset long–term fuel trim to 128 (0%).
Test Description
Numbers below refer to the step numbers on the Diagnos-
tic Table.

1F – 352IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0108
MANIFOLD ABSOLUTE PRESSURE HIGH VOLTAGE
Circuit Description
The Engine Control Module (ECM) uses the Manifold Ab-
solute Pressure (MAP) sensor to control the fuel delivery
and the ignition timing. The MAP sensor measures the
changes in the intake manifold pressure which results
from engine load (intake manifold vacuum) and the rpm
changes, and it converts these into voltage outputs. The
ECM sends a 5 volt reference voltage to the MAP sensor.
As the manifold pressure changes, the output of MAP sen-
sor also changes. By monitoring the Map sensor output
voltage, the ECM knows the manifold pressure. A low
pressure (low voltage) output voltage will be about 1.0 to
1.5 volts while the higher pressure (high voltage) output
voltage will be about 4.5 to 4.8 volts at Wide Open
Throttle(WOT). The MAP sensor is also used, under cer-
tain conditions to measure Barometric Pressure (BARO),
allowing the ECM to make adjustments for different alti-
tude.
Conditions for Setting the DTC
S MAP is greater than 103 kPa (15 psi)
S No Throttle Position (TP) sensor fail conditions
present.
S Engine is running more than 10 seconds.
S TP sensor is less than 10% if the rpm is less than
2500.
S TP sensor is less than 35 % if the rpm is great than
2500.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illumi-
nate.S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
S The ECM will substitute a fixed MAP value and use
TP sensor to control the fuel delivery. (The scan
tool will not show defaulted value.)
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
With the ignition ON and the engine stopped, the manifold
pressure is equal to atmospheric pressure and the signal
voltage will be high. This information is used by the ECM
as an indication of vehicle altitude. Comparison of this
reading with a known good vehicle with the same sensor
is a good way to check the accuracy of a suspect sensor.
Readings should be the same 12 kPa.
If a DTC P0108 is intermittent, refer to ”Manifold Absolute
Pressure Check” in this section for further diagnosis.
DTC P0108 may set as result of a misfire. If misfire is pres-
ent, repair the cause of misfire before using this table. The
misfire counters may be used to determine which cylin-
der(s) is misfiring.
Note : After repairs, use the scan tool FUEL TRIM RESET
function to reset long–term fuel trim to 128 (0%).

ENGINE CONTROLS 1F – 353
DAEWOO V–121 BL4
If DTC P0172 is also set, check 5 volt reference circuit for
short to voltage.
Test Description
Numbers below refer to the step numbers on the Diagnos-
tic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
2. This step will determine if DTC P0108 is the result
of a hard failure or an intermittent condition.
3. This step simulates conditions for a DTC P0107. If
the ECM recognizes the change, the ECM, the 5
volt reference and the sensor signal circuits are
OK.5. This step also looks for an open in the sensor
ground circuit. If the circuit was open, additional
DTCs will also be set. If no other DTCs are set and
the circuit is found to be open, then the open must
be between the MAP sensor and the electrical con-
nector ground splice.
6. When the sensor signal circuit is shorted to battery
voltage, the TP will be displayed above 0% at all
times and A/C High Side will be displayed high. The
vehicle will also remain in Open Loop.
8. The MAP sensor vacuum source should only sup-
ply vacuum to the MAP sensor. Check the vacuum
port for a restriction caused by casting flash.
9. Disconnect all sensors that use a 5 volt reference
one at a time while monitoring the short on the 5
volt reference circuit. Replace any sensor that may
have caused the short on the 5 volt reference cir-
cuit.
11. The replacement ECM must be programmed to the
latest Techline procedure for the ECM reprogram-
ming.
DTC P0108 – Manifold Absolute Pressure High Voltage
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Start the engine.
3. Read the Manifold Absolute Pressure (MAP).
Does the scan tool display a MAP of the specified
value or over?85 kPaGo to Step 3Go to Step 4
31. Turn the ignition switch OFF.
2. Disconnect the MAP sensor electrical connec-
tor.
3. Turn the ignition switch ON.
Does the MAP read less than the specified value?28 kPaGo to Step 5Go to Step 6
41. Turn the ignition switch ON with the engine
OFF, review the Freeze Frame data, and note
the parameters.
2. Operate the vehicle within the freeze frame
conditions and Conditions For Setting the DTC
as noted.
Does the scan tool display MAP equal to or greter
than the specified value?85 kPaGo to Step 3Go to
”Diagnostic
Aids”
5Probe the MAP sensor signal ground circuit at termi-
nal 3 with a test light connected to battery +.
Does the test light illuminate?–Go to Step 7Go to Step 11
6Check the MAP sensor signal circuit at terminal M8
of ECM for a short to voltage and repair as needed.
Is a repair necessary?–Go to Step 14Go to Step 12