2004 DAEWOO LACETTI Lamp

5A1 – 148IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE(DTC) P1851
SOLENOID 1 OUTPUT SHORTED TO POWER
Circuit Description
The shift solenoids are two identical, normally open elec-
tronic exhaust valves that control upshifts and downshifts
in all forward gear ranges. These shift solenoids work to-
gether in a combination of ON and OFF sequences to con-
trol the line pressure and shift mechanisms(clutches,
brakes).
Solenoid 1 controls the high or low of the line pressure
(flow to each clutch valve) by the operation type (ON/
OFF), i.e. solenoid 1 is ON, line pressure will be low
(87~116psi (6~8bar)), solenoid 1 is OFF, line pressure will
be high (232~261psi (16~18bar)). Solenoid 2 controls the
oil flow to clutch valve E or lock–up clutch valve by the ON/
OFF signal.
The TCM monitors numerous inputs to determine the ap-
propriate solenoid state combination and transaxle gear
tor the vehicle operating conditions.
Conditions for Setting the DTCS Solenoid wiring shorted to power.
S No DTC P1850, P1852.
S Immediately after the above condition occurs.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.
S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction has
not occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S When DTC P1851 sets, the possible cause of fault
could be solenoid 1.

5A1 – 150IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE(DTC) P1852
SOLENOID 1 OUTPUT OPEN
Circuit Description
The shift solenoids are two identical, normally open elec-
tronic exhaust valves that control upshifts and downshifts
in all forward gear ranges. These shift solenoids work to-
gether in a combination of ON and OFF sequences to con-
trol the line pressure and shift mechanisms(clutches,
brakes).
Solenoid 1 controls the high or low of the line pressure
(flow to each clutch valve) by the operation type (ON/
OFF), i.e. solenoid 1 is ON, line pressure will be low
(87~116psi (6~8bar)), solenoid 1 is OFF, line pressure will
be high (232~261psi (16~18bar)). Solenoid 2 controls the
oil flow to clutch valve E or lock–up clutch valve by the ON/
OFF signal.
The TCM monitors numerous inputs to determine the ap-
propriate solenoid state combination and transaxle gear
tor the vehicle operating conditions.
Conditions for Setting the DTC
S Solenoid wiring open.
S No DTC P1850, P1851.S Immediately after the above condition occurs.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.
S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear by hydraulic control.
S After ignition OFF/ON : 3rd gear by hydraulic con-
trol. Possible P, R and N also possible.
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction has
not occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S When DTC P1852 sets, the possible cause of fault
could be solenoid 1.

5A1 – 152IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE(DTC) P1853
SOLENOID 2 OUTPUT SHORTED TO GROUND
Circuit Description
The shift solenoids are two identical, normally open elec-
tronic exhaust valves that control upshifts and downshifts
in all forward gear ranges. These shift solenoids work to-
gether in a combination of ON and OFF sequences to con-
trol the line pressure and shift mechanisms(clutches,
brakes).
Solenoid 2 controls the high or low of the line pressure
(flow to each clutch valve) by the operation type (ON/
OFF), i.e. solenoid 2 is ON, line pressure will be low
(87~116psi (6~8bar)), solenoid 1 is OFF, line pressure will
be high (232~261psi (16~18bar)). Solenoid 2 controls the
oil flow to clutch valve E or lock–up clutch valve by the ON/
OFF signal.
The TCM monitors numerous inputs to determine the ap-
propriate solenoid state combination and transaxle gear
tor the vehicle operating conditions.
Conditions for Setting the DTC
S Solenoid wiring shorted to ground.
S No DTC P1854, P1855.S Immediately after the above condition occurs.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.
S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear by hydraulic control.
S After ignition OFF/ON : 3rd gear by hydraulic con-
trol. Possible P, R and N also possible.
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction has
not occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S When DTC P1853 sets, the possible cause of fault
could be solenoid 2.

5A1 – 154IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE(DTC) P1854
SOLENOID 2 OUTPUT SHORTED TO POWER
Circuit Description
The shift solenoids are two identical, normally open elec-
tronic exhaust valves that control upshifts and downshifts
in all forward gear ranges. These shift solenoids work to-
gether in a combination of ON and OFF sequences to con-
trol the line pressure and shift mechanisms(clutches,
brakes).
Solenoid 2 controls the high or low of the line pressure
(flow to each clutch valve) by the operation type (ON/
OFF), i.e. solenoid 2 is ON, line pressure will be low
(87~116psi (6~8bar)), solenoid 1 is OFF, line pressure will
be high (232~261psi (16~18bar)). Solenoid 2 controls the
oil flow to clutch valve E or lock–up clutch valve by the ON/
OFF signal.
The TCM monitors numerous inputs to determine the ap-
propriate solenoid state combination and transaxle gear
tor the vehicle operating conditions.
Conditions for Setting the DTC
S Solenoid wiring shorted to power.S No DTC P1853, P1855.
S Immediately after the above condition occurs.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.
S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear.
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction has
not occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S When DTC P1854 sets, the possible cause of fault
could be solenoid 2.

5A1 – 156IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE(DTC) P1855
SOLENOID 2 OUTPUT OPEN
Circuit Description
The shift solenoids are two identical, normally open elec-
tronic exhaust valves that control upshifts and downshifts
in all forward gear ranges. These shift solenoids work to-
gether in a combination of ON and OFF sequences to con-
trol the line pressure and shift mechanisms(clutches,
brakes).
Solenoid 2 controls the high or low of the line pressure
(flow to each clutch valve) by the operation type (ON/
OFF), i.e. solenoid 2 is ON, line pressure will be low
(87~116psi (6~8bar)), solenoid 1 is OFF, line pressure will
be high (232~261psi (16~18bar)). Solenoid 2 controls the
oil flow to clutch valve E or lock–up clutch valve by the ON/
OFF signal.
The TCM monitors numerous inputs to determine the ap-
propriate solenoid state combination and transaxle gear
tor the vehicle operating conditions.
Conditions for Setting the DTC
S Solenoid wiring open.
S No DTC P1853, P1854.S Immediately after the above condition occurs.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.
S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear.
S After ignition OFF/ON : 3rd gear by hydraulic con-
trol. Possible P, R and N also possible.
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction has
not occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S When DTC P1855 sets, the possible cause of fault
could be solenoid 2.

5A1 – 158IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE(DTC) P1861
EDS 4 OUTPUT SHORTED TO GROUND
Circuit Description
The pressure control valves (EDS valves 3,4,5 and 6) are
precision electronic pressure regulators that control the
operation of the clutches, brakes and lock–up clutch.
The valve reduces the system pressure with which the
downstream solenoid valves and electrical pressure regu-
lating valves are supplied. It is possible to use smaller so-
lenoid valves as a result. The EDS require a constant input
pressure.
Conditions for Setting the DTC
S Output voltage of the EDS 4 is less than 2 volt.
S No DTC P1862, P1863.
S Immediately after the above condition occurs.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear by hydraulic control.
S After ignition OFF/ON : 3rd gear by hydraulic con-
trol. Possible P, R and N also possible.
S Power supply cut off to the EDS valve.
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction has
not occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S When DTC P1861 sets, the possible cause of fault
could be EDS4 valve.

5A1 – 160IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE(DTC) P1862
EDS 4 OUTPUT SHORTED TO POWER
Circuit Description
The pressure control valves (EDS valves 3,4,5 and 6) are
precision electronic pressure regulators that control the
operation of the clutches, brakes and lock–up clutch.
The valve reduces the system pressure with which the
downstream solenoid valves and electrical pressure regu-
lating valves are supplied. It is possible to use smaller so-
lenoid valves as a result. The EDS require a constant input
pressure.
Conditions for Setting the DTC
S Output voltage of the EDS 4 (at ON) is 12 volt.
S No DTC P1861, P1863.
S Immediately after the above condition occurs.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear by hydraulic control.
S After ignition OFF/ON : 3rd gear by hydraulic con-
trol. Possible P, R and N also possible.
S Power supply cut off to the EDS valve.
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction has
not occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S When DTC P1862 sets, the possible cause of fault
could be TCM.

5A1 – 162IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE(DTC) P1863
EDS 4 OUTPUT OPEN
Circuit Description
The pressure control valves (EDS valves 3,4,5 and 6) are
precision electronic pressure regulators that control the
operation of the clutches, brakes and lock–up clutch.
The valve reduces the system pressure with which the
downstream solenoid valves and electrical pressure regu-
lating valves are supplied. It is possible to use smaller so-
lenoid valves as a result. The EDS require a constant input
pressure.
Conditions for Setting the DTC
S Output ampere of the EDS 4 is less than 10mA.
S No DTC P1861, P1862.
S Immediately after the above condition occurs.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear by hydraulic control.
S After ignition OFF/ON : 3rd gear by hydraulic con-
trol. Possible P, R and N also possible.
S Power supply cut off to the EDS valve.
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction has
not occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S When DTC P1863 sets, the possible cause of fault
could be EDS4 valve.