2004 DAEWOO LACETTI Ground

4F – 32IANTILOCK BRAKE SYSTEM
DAEWOO V–121 BL4
J3B14F08
Right Rear
Wheel Speed
Sensor EBCM
BRN
BRN
GRYC302 C110
WHT WHT
WHT1
110
1 3
3
2
2
DIAGNOSTIC TROUBLE CODE (DTC) C0050
RIGHT REAR WHEEL SPEED SENSOR CIRCUIT
MALFUNCTION
Circuit Description
The toothed wheel generates a voltage pulse as it moves
past the sensor. Each tooth–gap–tooth series on the
wheel generates the pulses. The electronic brake control
module (EBCM) uses the frequency of these pulses to de-
termine the wheel speed. The voltage generated depends
on the air gap between the sensor and the toothed wheel,
and on the wheel speed.
Diagnosis
This procedure checks for a malfunctioning wheel speed
sensor, a short to ground or to voltage in the wiring, or a
contact problem in a connector.
Cause(s)
S The wheel speed sensor is defective or discon-
nected.
S There is a problem in the wiring.
S There is a problem with a connector.
S There is a problem in the toothed ring.
S Wrong installed WSS.
S Wrong sensor signal.
S Signal noise via WSS.
Fail Action
ABS action is disabled, and the ABS warning lamp is ON.
EBD is enabled. (Refer to the EBD failure matrix in this
section)
Test Description
The number(s) below refer to step(s) on the diagnostic
table.1. This step begins an examination for a defective
wheel speed sensor.
6. This step tests the wiring for a short to voltage.
8. This step tests the wiring for a short to ground.
10. This step tests for an open or high resistance in the
wiring.
Diagnostic Aids
Be sure that the speed sensor wiring is properly routed and
retained. This will help to prevent false signals due to the
pickup of electrical noise.
It is very important to perform a thorough inspection of the
wiring and the connectors. Failure to inspect the wiring
and the connectors carefully and completely may result in
misdiagnosis, causing part replacement with the reap-
pearance of the malfunction.
You can use the scan tool to monitor wheel speeds during
a road test. Watch the wheel speeds being displayed on
the scan tool to see if any of the readings is unusual, such
as one sensor varying in speed from the other three, a sig-
nal going intermittently high or low, etc. If this does not
identify the intermittent, wet the speed sensor harness on
the underside of the vehicle and perform a road test, moni-
toring wheel speeds with the scan tool.
Important : If the WSS signal fault input to the EBCM, the
ABS warning lamp turns on. As if a sensor signal fault can
be removed by the scan tool, the ABS warning lamp
doesn’t turn off. In order to turn ABS warning lamp off, you
should drive a car up to 12 km/h.

ANTILOCK BRAKE SYSTEM 4F – 33
DAEWOO V–121 BL4
DTC C0050 – Right Rear Wheel Speed Sensor Circuit Malfunction
StepActionValue(s)YesNo
1Examine the wheel speed sensor.
Are there any signs of physical damage?–Go to Step 3Go to Step 2
21. Turn the ignition switch to LOCK.
2. Disconnect the left rear wheel speed sensor
connector.
3. Use a digital voltmeter (DVM) to measure the
resistance between the sensor terminals.
Is the resistance within the specified value at
approximately 25°C (77°F)?1280–1920 WGo to Step 4Go to Step 3
3Replace the wheel speed sensor.
Is the repair complete?–System OK–
41. Switch the DVM to the AC millivolt range.
2. Measure the voltage output of between the
wheel speed sensor terminals while rotating
the wheel about 1 revolution every 2 seconds.
Is the output within the specified value?
120 vGo to Step 6Go to Step 5
5Replace the speed sensor or the toothed wheel as
required.
Is the repair complete?–System OK–
61. Disconnect the harness from the EBCM.
2. Connect a DVM between ground and one ter-
minal of the wheel speed connector.
3. Turn the ignition to ON.
4. Repeat the above test for the other terminal of
the wheel speed connector.
Is the voltage for either of these terminals within the
specified value?> 1 vGo to Step 7Go to Step 8
7Repair the short to voltage in the affected circuit.
Is the repair complete?–System OK–
81. Turn the ignition switch to LOCK.
2. Measure the resistance to ground from termi-
nal 1 at the harness EBCM connector.
3. Measure the resistance to ground from termi-
nal 2 at the harness EBCM connector.
Is the resistance at either circuit less than the speci-
fied value?Go to Step 9Go to Step 10
9Repair the short to ground in the affected circuit.
Is the repair complete?–System OK–
101. Measure the resistance between terminal 1 at
the harness EBCM connector and the harness
wheel speed sensor connector terminal con-
nected to the WHT wire.
2. Measure the resistance between terminal 2 at
the harness EBCM connector and the harness
wheel speed sensor connector terminal con-
nected to the GRY wire.
Is the resistance on either circuit within the specified
value?> 5 WGo to Step 11Go to Step 12

ANTILOCK BRAKE SYSTEM 4F – 35
DAEWOO V–121 BL4
J3B14F09
DLC
(Data Link
Connector)
EBCM
DK BLUDK BLU
BLK/WHTC202
C110
11 2
1912 19
G106
DIAGNOSTIC TROUBLE CODE (DTC) C0060/C0065
LEFT FRONT INLET AND OUTLET VALVE SOLENOID
FAULT
Circuit Description
The solenoid valve coil circuits are supplied with power
from the battery when the valve relay is energized.
Switched ground is provided by the electronic brake con-
trol module (EBCM) to each coil.
Diagnosis
This procedure checks whether the left front inlet and out-
let valves are functioning.
Cause(s)
S A valve has failed.S A solenoid coil is open or shorted.
Fail Action
ABS is disabled, and the ABS warning lamp is turned ON
for the remainder of the ignition cycle. EBD is disabled. If
the failure is intermittent, the EBCM will enable the system
at the next ignition cycle and set a history DTC.
Test Description
The number(s) below refer to step(s) on the diagnostic
table.
1. This step begins the test of the inlet valve.
3. This step tests the outlet valve.

ANTILOCK BRAKE SYSTEM 4F – 37
DAEWOO V–121 BL4
J3B14F09
DLC
(Data Link
Connector)
EBCM
DK BLUDK BLU
BLK/WHTC202
C110
11 2
1912 19
G106
DIAGNOSTIC TROUBLE CODE (DTC) C0070/C0075
RIGHT FRONT INLET AND OUTLET VALVE SOLENOID
FAULT
Circuit Description
The solenoid valve coil circuits are supplied with power
from the battery when the valve relay is energized.
Switched ground is provided by the electronic brake con-
trol module (EBCM) to each coil.
Diagnosis
This procedure checks whether the right front inlet and
outlet valves are functioning.
Cause(s)
S A solenoid coil is open or shorted.Fail Action
ABS is disabled, and the ABS warning lamp is turned ON
for the remainder of the ignition cycle. EBD is disabled. If
the failure is intermittent, the EBCM will enable the system
at the next ignition cycle and set a history DTC.
Test Description
The number(s) below refer to step(s) on the diagnostic
table.
1. This begins the test of the inlet valve.
3. This tests the outlet valve.

ANTILOCK BRAKE SYSTEM 4F – 39
DAEWOO V–121 BL4
J3B14F09
DLC
(Data Link
Connector)
EBCM
DK BLUDK BLU
BLK/WHTC202
C110
11 2
1912 19
G106
DIAGNOSTIC TROUBLE CODE (DTC) C0080/C0085
LEFT REAR INLET AND OUTLET VALVE SOLENOID
FAULT
Circuit Description
The solenoid valve coil circuits are supplied with power
from the battery when the valve relay is energized.
Switched ground is provided by the electronic brake con-
trol module (EBCM) to each coil.
Diagnosis
This procedure checks whether the left rear inlet and outlet
valves are functioning.
Cause(s)
S A valve has failed.S A solenoid coil is open or shorted.
Fail Action
ABS is disabled, and the ABS warning lamp is turned ON
for the remainder of the ignition cycle. EBD is disabled. If
the failure is intermittent, the EBCM will enable the system
at the next ignition cycle and set a history DTC.
Test Description
The number(s) below refer to step(s) on the diagnostic
table.
1. This begins the test of the inlet valve.
3. This tests the outlet valve.

ANTILOCK BRAKE SYSTEM 4F – 41
DAEWOO V–121 BL4
J3B14F09
DLC
(Data Link
Connector)
EBCM
DK BLUDK BLU
BLK/WHTC202
C110
11 2
1912 19
G106
DIAGNOSTIC TROUBLE CODE (DTC) C0090/C0095
RIGHT REAR INLET AND OUTLET VALVE SOLENOID
FAULT
Circuit Description
The solenoid valve coil circuits are supplied with power
from the battery when the valve relay is energized.
Switched ground is provided by the electronic brake con-
trol module (EBCM) to each coil.
Diagnosis
This procedure checks whether the right rear inlet and out-
let valves are functioning.
Cause(s)
S A valve has failed.S A solenoid coil is open or shorted.
Fail Action
ABS is disabled, and the ABS warning lamp is turned ON
for the remainder of the ignition cycle. EBD is disabled. If
the failure is intermittent, the EBCM will enable the system
at the next ignition cycle and set a history DTC.
Test Description
The number(s) below refer to step(s) on the diagnostic
table.
1. This begins the test of the inlet valve.
3. This tests the outlet valve.

ANTILOCK BRAKE SYSTEM 4F – 43
DAEWOO V–121 BL4
J3B14F04
60A Ef230A Ef5
2
42
C107 C105
2
C110
G106
A19
A13 A1 A14
C110 C202
C202WHT LT GRN
DK
GRN LT GRN/
BLK
BLK
DK BLUDK BLU
PPL/WHT
PPL/WHT ABS
TCS Parking
Brake
Hot at all times
RED REDRED/WHT
Ignition
Switch
RED
RED
I/P Cluster
EBCM8
20
22 2216 41
1211
18 1621
1
C107
10A F410AF11
32 31
43
6 62 C201
C201 C201C201
C110 C202
Hot in Run and Start
30
4
1711
C202
15
B15
DLC
(Data Link
Connector)12
G106
BLK/WHTOil Feeding
Connector
”2” Ter.
BRNBRN BRN
BRN PNK PNK PNK
19J1
59B1
ONStart Lock
Acc
IG1
19
DIAGNOSTIC TROUBLE CODE (DTC) C0110
PUMP MOTOR CIRCUIT MALFUNCTION
Circuit Description
When the electronic brake control module (EBCM)
grounds the pump motor relay, it closes and provides bat-
tery voltage to the pump motor if the valve relay is closed.
The EBCM senses the voltage applied to the pump motor
to verify motor operation.
Diagnosis
This DTC sets when the EBCM detects B+ without motor
relay activation or if the EBCM does not detect B+ after
motor relay activation.
Cause(s)
S There is a faulty terminal in pump motor connector.
S There is a faulty terminal in EBCM connector.
S There is a problem in the ABS wiring harness.
S There is high resistance in the chassis ground.
S The EBCM is defective.S There is a problem in the wiring from pump motor
connector to the motor.
Fail Action
ABS is disabled, and the ABS warning lamp is ON. EBD
is disabled.
Test Description
The number(s) below refer to step(s) on the diagnostic
table.
1. This step checks for connector damage.
3. This step checks for a poor ground connection.
7. This step checks for a possible problem with the
motor connector at the ABS unit.
Diagnostic Aids
It is very important to perform a thorough inspection of the
wiring and the connectors. Failure to do so may result in
misdiagnosis, causing part replacement with reappear-
ance of the malfunction.

4F – 44IANTILOCK BRAKE SYSTEM
DAEWOO V–121 BL4
DTC C0110 – Pump Motor Circuit Malfunction
StepActionValue(s)YesNo
11. Disconnect connector from the EBCM.
2. Examine terminal 16 on the harness connector
and on the EBCM connector.
Is the terminal damaged or corroded?–Go to Step 2Go to Step 3
2Repair or replace the terminal, the connector, the
wiring harness, or the EBCM as required.
Is the repair complete?–System OK–
3Measure the resistance from terminal 16 of the har-
ness connector to a good chassis ground.
Is the resistance equal to the specified value?
0 WGo to Step 7Go to Step 4
4Measure the resistance at the chassis ground con-
nection G106.
Is the resistance equal to the specified value?
0 WGo to Step 6Go to Step 5
5Repair the connection at chassis ground G106.
Is the repair complete?–System OK–
6Repair the open or the high resistance in the harness
between terminal 16 of connector J1 and the ground
lug, or replace the ABS wiring harness.
Is the repair complete?–System OK–
71. Remove the ABS unit from the vehicle.
2. Disconnect connector J2 and examine the ter-
minals.
Is there any sign of damage or corrosion that would
prevent a good ground contact?–Go to Step 8Go to Step 9
8Repair or replace the defective terminal, connector,
or ABS unit as required.
Is the repair complete?–System OK–
9Replace the ABS unit.
Is the repair complete?–System OK–