2004 DAEWOO LACETTI battery

ENGINE CONTROLS 1F – 535
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1121
THROTTLE POSITION SENSOR INTERMITTENT HIGH
VOLTAGE
Circuit Description
The Throttle Position (TP) sensor circuit provides a volt-
age signal that changes relative to throttle blade angle.
The TP sensor sends a voltage signal back to the Engine
Control Module (ECM) relative to the throttle plate open-
ing. The voltage signal will vary from approximately 0.33
volts at closed throttle, to over 4.3 volts at Wide Open
Throttle (WOT).
The TP signal is used by the ECM for fuel control and for
most of the ECM controlled outputs. The TP signal is one
of the most important inputs used by the ECM for fuel con-
trol and most of the ECM controlled outputs. If the ECM
detects a TP signal that is intermittently above the range
of the TP sensor, Diagnostic Trouble Code (DTC) P1121
will be set.
Conditions for Setting the DTC
S TP sensor voltage indicates a throttle voltage inter-
mittently greater than 4.9 volts.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will not illumi-
nate.
S The ECM will store conditions which were present
when the DTC set as Failure Records data only.
This information will not be stored as Freeze Frame
data.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S A history will clear after 40 consecutive warm–up
cycles in which the diagnostic runs without a fault.S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Check for the following conditions:
S Poor connection at the ECM. Inspect harness con-
nectors for backed–out terminals, improper mating,
broken locks, improperly formed or damaged termi-
nals, and poor terminal–to–wire connection.
S Damaged harness. Inspect the wiring harness for
damage. If the harness appears OK, observe the
throttle position display on the scan tool while mov-
ing connectors and wiring harnesses related to the
TP sensor. A change in the display will indicate the
location of the fault.
If DTC P1121 cannot be duplicated, reviewing the Fail Re-
cords vehicle mileage since the diagnostic test last failed
may help determine how often the condition that caused
the DTC to be set occurs. This may assist in diagnosing
the condition.
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.

ENGINE CONTROLS 1F – 537
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1122
THROTTLE POSITION SENSOR INTERMITTENT LOW
VOLTAGE
Circuit Description
The Throttle Position (TP) sensor circuit provides a volt-
age signal that changes relative to throttle blade angle.
The TP sensor sends a voltage signal back to the Engine
Control Module (ECM) relative to the throttle plate open-
ing. The voltage signal will vary from approximately 0.33
volts at closed throttle, to over 4.3 volts at Wide Open
Throttle (WOT).
The TP signal is used by the ECM for fuel control and for
most of the ECM controlled outputs. The TP signal is one
of the most important inputs used by the ECM for fuel con-
trol and most of the ECM controlled outputs. If the ECM
detects a TP signal that is intermittently above the range
of the TP sensor, Diagnostic Trouble Code (DTC) P1122
will be set.
Conditions for Setting the DTC
S TP sensor voltage indicates a throttle voltage inter-
mittently less than 0.14 volts.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will not illumi-
nate.
S The ECM will store conditions which were present
when the DTC set as Failure Records data only.
This information will not be stored as Freeze Frame
data.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S A history will clear after 40 consecutive warm–up
cycles in which the diagnostic runs without a fault.S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Check for the following conditions:
S Poor connection at the ECM. Inspect harness con-
nectors for backed–out terminals, improper mating,
broken locks, improperly formed or damaged termi-
nals, and poor terminal–to–wire connection.
S Damaged harness. Inspect the wiring harness for
damage. If the harness appears OK, observe the
throttle position display on the scan tool while mov-
ing connectors and wiring harnesses related to the
TP sensor. A change in the display will indicate the
location of the fault.
If DTC P1122 cannot be duplicated, reviewing the Fail Re-
cords vehicle mileage since the diagnostic test last failed
may help determine how often the condition that caused
the DTC to be set occurs. This may assist in diagnosing
the condition.
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.

ENGINE CONTROLS 1F – 539
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1133
FRONT HEATED OXYGEN SENSOR (HO2S1) TOO FEW
TRANSITION
Circuit Description
The Engine Control Module (ECM) continuously monitors
the Front Heated Oxygen Sensor (HO2S1) activity for 100
seconds. During the monitor period, the ECM counts the
number of times that the HO2S1 switches from rich to lean
and from lean to rich. With this information, a total for all
switches can be determined. If the number of switches is
too low, a Diagnostic Trouble code (DTC) P1133 will set.
The lean–to–rich and rich–to–lean are less than 15
switches.
Conditions for Setting the DTC
S HO2S1 signal switches from 0.3 to 0.6 volts and
0.6 to 0.3 volts is less than 15 times within 90sec-
onds.
S Closed loop stoichiometry.
S Engine Coolant Temperature (ECT) is greater than
70 °C (158 °F).
S System voltage is greater than 10 volts.
S Engine run time is greater than 60 seconds.
S Purge Duty Cycle (DC) is less than 20%.
S The rpm is between 1600 and 4300.
S Airflow is between 9 and 40 g/sec.S DTCs P0106, P0107, P0108, P0117, P0118,
P0122, P0123, P0131, P0132, P0134, P0135,
P1167, P0171, P1171, P0172, P0201, P0202,
P0203, P0204, P0300, P0336, P0337, P0351,
P0352, P0402, P0404, P0405, P0406, P0506,
P0507, P1404, and P0443 are not set.
S 2 second delay after conditions are met.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive ignition cycle with a fail.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.

1F – 544IENGINE CONTROLS
DAEWOO V–121 BL4
S The DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
A malfunction in the HO2S1 ignition feed or ground circuit
may cause a DTC P1134 to set. Check HO2S1 circuitry for
intermittent faults or poor connections. If connections and
wiring are OK and DTC P1134 continues to set, replace
the HO2S1.
Reviewing the Failure Records vehicle mileage since the
diagnostic test last failed may help determine how open
the condition that caused the DTC to be set occurs. This
may assist in diagnosing the condition.Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Chart.
3. A condition that affects pre–converter and post–
converter oxygen sensors indicates probable con-
tamination. To avoid damaging replacement sen-
sors, correct the condition which caused the
contamination before replacing the affected sen-
sors.
5. This step checks for conditions which may cause
the oxygen sensor to appear faulty. Correct any of
the described conditions if present.
8. To avoid damaging replacement sensors, correct
the condition which caused the contamination be-
fore replacing the affected sensors
DTC P1134 – Front Heated Oxygen Sensor (HO2S1) Transition
Ratio
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
2Important : If any Diagnostic Trouble Codes (DTCs)
are set, refer to those DTCs before processing with
this diagnostic chart.
1. Install a scan tool to the Data Link Connector
(DLC).
2. Start the engine and idle at normal operating
temperature.
3. Operate the engine within parameters specified
under Conditions for Setting the DTC.
4. Using a scan tool, monitor specific DTC info for
DTC P1134 until the DTC P1134 test runs.
5. Note the test result.
Does the scan tool indicate DTC P1134 failed this
ignition?–Go to Step 3Go to
”Diagnostic
Aids”
3Perform an exhaust system leak test.
If an exhaust leak is found, repair as needed.
The exhaust leak isolated?–Go to Step 14Go to Step 4
4Visually/physically inspect for the following items:
S Front Heated Oxygen Sensor (HO2S1) is se-
curely installed.
S Corrosion on the terminals.
S Terminal tension.
S HO2S1 wiring harness for poor terminal con-
nection or damaged wiring.
Is a problem found in any of the above areas?–Go to Step 7Go to Step 5

ENGINE CONTROLS 1F – 547
DAEWOO V–121 BL4
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
The DTC P1167 or rich exhaust is most likely caused by
one of the following items:S Leaking injector – A leaking or malfunctioning injec-
tor can cause the system to go rich causing a DTC
P0132.
S Pressure regulator – Check for a leaking fuel pres-
sure regulator diaphragm by checking for the pres-
ence of liquid fuel in the vacuum line to the regula-
tor.
DTC P1167 – Front Heated Oxygen Sensor (HO2S1) Rich in Decel
Fuel Cutoff (DFCO)
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Turn the ignition ON.
Any other component related Diagnostic Trouble
Codes (DTCs) set?–Go to
applicable DTC
tableGo to Step 3
31. Using a scan tool, observe the Front Heated
Oxygen Sensor (HO2S1) voltage while decel-
erating the engine.
2. The HO2S1 voltage should vary from specified
voltage (100–900 mV) and while decelerating
occasionally toggle below the specified voltage.
Is the HO2S1 voltage toggle?550 mVGo to Step 4Go to
”DTC P0134
Oxygen Sensor
No Activity”
4Check the items in ”Diagnostic Aids” and repair or re-
place component as needed. Refer to ”Fuel System
Diagnosis”.
Is the repair complete?–Go to Step 6Go to Step 5
51. Turn the ignition OFF.
2. Replace the Engine Control Module (ECM).
Is the repair complete?–Go to Step 6–
61. Using the scan tool, clear the Diagnostic
Trouble Codes (DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the Conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?–Go to Step 7Go to Step 2
7Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
Applicable DTC
tableSystem OK

1F – 548IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1171
FUEL TRIM SYSTEM LEAN DURING POWER
ENRICHMENT
System Description
The internal circuitry of the Engine control Module (ECM)
can identify if the vehicle fuel system is capable of supply-
ing adequate amounts of fuel during heavy acceleration(
power enrichment). When a Power Enrichment (PE)
mode of operation is requested by heavy acceleration dur-
ing Closed Loop operation, the ECM will provide more fuel
to the engine. Under these conditions the ECM should de-
tect a rich condition. If this reich condition is nor detected
at this time, Diagnostic Trouble Code (DTC) P1171 will set.
A plugged fuel filter or restricted fuel line can prevent ade-
quate amount of fuel from being supplied during Power
Enrichment mode.
Conditions for Setting the DTC
S HO2S1 voltage is less than 0.35 volts in Power En-
richment (PE) mode.
S Engine is operating in Closed Loop and in PE
mode.
S Engine Coolant Temperature (ECT) is greater than
60°C (140°F).
S System voltage is greater than 10 volts.
S Air/Fuel ration is less than 13.5:1.
S DTCs P0106, P0107, P0108, P0117, P0118,
P0122, P0123, P0171, P0172, P0201, P0202,
P0203, P0204, P0300, P0336, P0337, P0351,
P0352, P0402, P0404, P0405, P0406, P0506,
P0507, P1404, and P0443 are not set.
S 3 second delay after in PE mode.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after two consecutive ignition cycle with a fail.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
S The vehicle will operate in Open Loop.Conditions for Clearing the MIL/DTC
S The MIL will turn off after three consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.v
Diagnostic Aids
A restricted fuel filter can supply adequate amounts of fuel
at idle, but may not be able to supply enough fuel during
heavy acceleration.
Water or alcohol n fuel may cause low HO2S1 voltage dur-
ing acceleration.
Check for adequate amount of fuel in the Tank.
When the engine is idling or at steady cruise, the HO2S1
voltage should vary from between approximately a00 to
900 millivolts. During power enrichment mode, more fuel
is needed, and the HO2S1 should rise above 444 milli-
volts.
Check for faulty or plugged injector(s).
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
4. This step checks to see if the HO2S1 is operating
properly.
6. If no faults have been found at this point and no
additional DTCs were set, refer to ”Diagnostic Aids”
in this section for additional checks and informa-
tion.

1F – 550IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1336
58X CRANK POSITION TOOTH ERROR NOT LEARNED
Circuit Description
In order to detect engine misfire at higher engine speeds,
the Engine Control Module (ECM) must know of any varia-
tion between the crankshaft sensor pulses. Most varia-
tions are due to the machining of the crankshaft reluctor
wheel. However, other sources of variation are also pos-
sible. A Crankshaft Position (CKP) system variation learn-
ing procedure must be performed any time a change is
made to the crankshaft sensor to crankshaft relationship
of if the ECM is replaced or reprogrammed. The ECM
measures the variations and then calculates compensa-
tion factors needed to enable the ECM to accurately de-
tect engine misfire at all speeds and loads. A scan tool
must be used to command the ECM to learn these varia-
tions. If for any reason the ECM is unable to learn these
variations or they are out of an acceptable range, the ECM
will set Diagnostic Trouble Code (DTC) P1336. An ECM
that has not had the CKP system variation learning proce-
dure performed due to replacement or reprogramming will
also set DTC P1336.
Conditions for Setting the DTC
S Tooth error not learned if the manufacture enable
counter is set to zero.
S DTCs P0106, P0107, P0108, P0117, P0118,
P0122, P0123, P0132, P0201, P0202, P0203,
P0204, P0325 , 0327, P0336, P0337, P0341,
P0342, P0351, P0352, P0402, P1404, P0404,
P0405, P0406 and P0502 are not set.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illumi-
nate.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffer.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF after four consecutive igni-
tion cycles in which the diagnostic runs without a
fault.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Disconnecting the ECM battery feed for more than
10 seconds.
S DTC(s) can be cleared by using the scan tool.Diagnostic Aids
CAUTION : To avoid personal injury when performing
the crankshaft position system variation learning
procedure, always set the vehice parking brake and
block the drive wheels. Release the throttle immedi-
ately when the engine starts to decelerate. Once the
learn procedure is completed, engine control will be
returned to the operator, and the engine will respond
to throttle position.
DTC P1336 will only set if the ECM has not learned the
CKP system variation. The ECM only needs to learn this
variation once per life cycle of the vehicle unless the crank
sensor to crankshaft relationship is disturbed. Removing
a part is considered a disturbance. A fully warmed engine
is critical to learning the variation correctly. If a valid learn
occurs, no other learns can be completed that ignition
cycle.
If the engine cuts out before the specified learn procedure
engine speed or at normal fuel cutoff rpm, the ECM is not
in the learn procedure mode.
Test Description
The number(s) below refer to step(s) on the diagnostic
table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the fault occurred. The information is then stored on
the scan tool for later reference.
2. Engine temperature is critical to properly learn the
CKP system variation. Failure to properly warm the
engine before performing this procedure will result
in an inaccurate measurement of the CKP system
variation. The ECM learns this variation as the en-
gine is decelerating and then allows engine control
to be returned to the operator. All accessories must
be OFF when learning the CKP system angle varia-
tion. If the A/C is not disabled when the learn pro-
cedure is enabled, the ECM will disable the A/C.
3. If after the specified number attempts the ECM
cannot learn the CKP system variation, then the
variation is too large and no further attempts should
be made until the variation problem is corrected.
4. Being unable to learn the procedure indicates that
the variation is out of range.
5. After the CKP system variation has been learned,
wait above 10 seconds with ignition switch OFF to
prevent being cleared the learned value.

1F – 552IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1391
G SENSOR ROUGH ROAD RATIONALITY
Circuit Description
TThe Gravity Sensing Rough Road (G) sensor is a vertical
low g–acceleration sensor. By sensing vertical accelera-
tion caused by bumps or potholes in the road, the Engine
Control Module (ECM) can determine if the changes in
crankshaft speed are due to engine misfire or are driveline
induced. If the G sensor detects a rough road condition,
the ECM misfire detection diagnostic will be de–activated.
The G sensor at rest output should be between 2.35–2.65
volts (+1G). During a rough road condition, the voltage
output can vary between 0.5 (–1G) and 4.5 volts (+3G).
Conditions for Setting the DTC
S Engine is running.
S Vehicle speed is less than or equal to 5 km/h (3.1
mph).
S G sensor output at idle indicates below –0.39 volts
or above 2.21 volts.
OR
S Engine is running more than 10 seconds and ve-
hicle speed is between 30 mph (50 km/h) and 70
mph (112 km/h).
S G sensor signal changes less than 0.00024 volts
while driving.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will not illumi-
nate.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.Conditions for Clearing the MIL/DTC
S A history Diagnostic Trouble Code (DTC) will clear
after 40 consecutive warm–up cycles without a
fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Check for the following conditions:
S Poor connection at the ECM – Inspect the harness
connections for backed–out terminals, improper
mating, broken locks, improperly formed or dam-
aged terminals, and poor terminal–to–wire connec-
tion.
S Damaged harness –– Inspect the wiring harness for
damage. If the harness appears to be OK, observe
the G sensor display on the scan tool while moving
connectors and wiring harnesses related to the sen-
sor. A change in the display will indicate the loca-
tion of the fault.
Since the G sensor shares the ECM 5 volt reference and
ground terminals with the A/C Pressure Sensor, a dam-
aged A/C Pressure Sensor harness or sensor could cause
a G sensor DTC to set. Refer to ”Multiple ECM Information
Sensor DTCs Set” in this section. in this section.
The G sensor will give correct voltages only if it is level and
mounted securely to its bracket.
Reviewing the Failure Records vehicle mileage since the
diagnostic test last failed may help determine how often
the condition that caused the DTC to be set occurs. This
may assist in diagnosing the con