2004 DAEWOO LACETTI fuse

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 67
DAEWOO V–121 BL4
DTC 57
Passenger Side Airbag Deployment Loop Resistance Is
Low
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Disconnect the connector of passenger side
airbag module.
3. Remove the connector of SDM.
4. Check the resistance between the terminal 1,2
of passenger side airbag module. Is the resist-
ance ?Go to Step 3Go to Step 2
2Replace the airbag wiring.–––
31. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Remove the DTC with scan tool.
4. Check the circuit. Does the DTC still exist?–Go to Step 4The system is
OK.
4Replace the passenger side airbag module.–––

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 69
DAEWOO V–121 BL4
DTC 58
Passenger Side Airbag Deployment Loop Is Shorted To
Ground
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute the SDM charger to be dis-
charged.
3. Visually check any damage for the airbag wir-
ing. Is the airbag wiring damaged?–Go to Step 3Go to Step 2
21. Check the resistance between the SDM and
the high, low terminal of passenger side airbag
module and the ground. Is the resistance
10KΩ?
10K ΩGo to Step 4Go to Step 3
3Replace the airbag wiring.–––
41. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Remove the DTC with scan tool.
4. Check the circuit. Does the DTC still exist?–Go to Step 5The System is
OK.
5Replace the passenger side airbag module.–––

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 71
DAEWOO V–121 BL4
DTC 59
Passenger Airbag Deployment Loop Is Shorted To Power
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute the SDM charger to be dis-
charged.
3. Visually check any damage for the airbag wir-
ing. Is the airbag wiring damaged?–Go to Sep 3Go to Step 2
21. Check the resistance between the SDM and
the high, low terminal of passenger side airbag
module and the battery. Is the resistance
10KΩ?
10K ΩGo to Step 4Go to Step 3
3Replace the airbag wiring.–––
41. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Remove the DTC with scan tool.
4. Check the circuit. Does the DTC still exist?–Go to Sep 5The system is
OK.
5Replace the passenger side airbag module.–––

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 73
DAEWOO V–121 BL4
DTC 80
Driver Side Airbag Sensor Loop Is Shorted To Power
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute the SDM charger to be dis-
charged.
3. Visually check any damage for the driver side
airbag sensor wiring and the connector. Are the
airbag wiring and connector OK?–Go to Step 3Go to Step 2
2Connect the wiring or repair the damage.
Check the system again.–––
31. Check the resistance between the SDM and
the high, low terminal of driver side airbag sen-
sor and the battery. Is the resistance 10KΩ?
10K ΩGo to Step 4Go to Step 6
41. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Remove the DTC with scan tool.
4. Check the circuit. Does the DTC still exist?–Go to Step 5The system is
OK.
5Replace the driver side airbag sensor.–––
6Replace the airbag wiring.–––

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 75
DAEWOO V–121 BL4
DTC 81
Driver Side Airbag Sensor Loop Is Shorted To Ground
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute the SDM charger to be dis-
charged.
3. Visually check any damage for the driver side
airbag sensor wiring and the connector. Are the
airbag wiring and connector OK?–Go to Step 3Go to Step 2
2Repair and reconnect the circuit. Check the circuit
again.–––
31. Check the resistance between the SDM and
the high, low terminal of driver side airbag sen-
sor and the ground. Is the resistance 10KΩ?
10K ΩGo toStep 5Go to Step 4
4Replace the airbag wiring.–––
51. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Remove the DTC with scan tool.
4. Check the circuit. Is the DTC still exist?–Go to Step 5The system is
OK.
6Replace the driver side airbag sensor.–––

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 77
DAEWOO V–121 BL4
DTC 82
Driver Side Airbag Sensor Communication Error
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute the SDM charger to be dis-
charged.
3. Visually check any damage for the driver side
airbag sensor wiring and the connector. Are the
airbag wiring and connector OK?–Go to Step 3Go to Step 2
2Replace the airbag wiring.–––
31. Replace the driver side airbag sensor.
2. Confirm the ignition switch ”ON”.
3. Remove the DTC with scan tool.
4. Check the circuit. Is the DTC still exist?–Go to Step 4The system is
OK.
4Replace the SDM.–––

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 79
DAEWOO V–121 BL4
DTC 83
Driver Side Airbag Sensor Failure
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute the SDM charger to be dis-
charged.
3. Visually check any damage for the driver side
airbag sensor wiring and the connector. Are the
airbag wiring and connector damaged?–Go to Step 2Go toStep 3
2Replace the wiring of airbag sensor.–––
3Replace the driver side airbag sensor.–––

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 81
DAEWOO V–121 BL4
DTC 84
Passenger Side Airbag Sensor Loop Is Shorted To
Power
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute the SDM charger to be dis-
charged.
3. Visually check any damage for the passenger
side airbag sensor wiring and the connector.
Are the airbag wiring and connector damaged?–Go to Step 3Go to Step 2
2Repair and reconnect the circuit. Check the circuit
again.–––
3Check the resistance between the SDM and the
high, low terminal of passenger side airbag sensor
and the battery. Is the resistance 10KΩ?
10K ΩGo to Step 5Go to Step 4
4Replace the airbag wiring.–––
51. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Remove the DTC with scan tool.
4. Check the circuit. Is the DTC still exist?–Go to Step 6The system is
OK.
6Replace the passenger side airbag sensor.–––