2004 DAEWOO LACETTI transmission fluid

5A1 – 90IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DTC P0710 – Transmission Fluid Temperature Sensor Circuit
Malfunction
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the check completed?–Go to Step 2Go to ”On–
Board Diagnos-
tic System
Check”
21. Install the scan tool.
2. Turn the ignition ON, with the engine OFF.
3. Record then clear DTC(s) and turn the ignition
OFF, then turn the ignition ON.
4. Select TFT on the scan tool.
5. Drive the vehicle and observe the scan tool for
either of the flowing conditions:
6. The TFT does not change more than 1.5°C
(34.7°F) in 80 seconds since start–up.
7. The TFT changes more than 20°C (68°F) with-
in 7 seconds (unrealistic change).
Did either of the fail conditions occur?–Go to Step 3Go to ”Diag-
nostic Aids”
31. Turn the ignition OFF.
2. Disconnect the transaxle wiring connector.
3. Measure the resistance between terminals 9
and 4 of the transaxle wiring connector.
Is the resistance within the values shown?TFT 25°C
990 ΩGo to Step 7Go to Step 4
41. Remove the oil pan.
2. Disconnect the wiring connector of the trans-
axle fluid temperature sensor.
3. Inspect the automatic transaxle wiring harness
for an intermittent short or open.
Was a problem found?–Go to Step 5Go to Step 6
5Replace the automatic transaxle wiring harness.
Is the replacement complete?–System OK–
6Replace the TFT sensor.
Is the action complete?–System OK–
71. Disconnect the automatic transaxle wiring con-
nector and disconnect the wiring connector of
the TCM(transaxle control module).
2. Measure the resistance between terminal 4 of
the transaxle wiring connector and terminal B1
of the TCM wiring connector.
3. Measure the resistance between terminal 9 of
the transaxle wiring connector and terminal A4
of the TCM wiring connector.
Is the resistance within the values shown?0ΩGo to Step 9Go to Step 8
81. Inspect the automatic transaxle wiring harness
for an intermittent short to ground or open con-
dition.
2. Inspect the automatic TFT sensor wiring har-
ness for an intermittent short to ground or open
condition.
3. Repair the circuits if necessary.
Is the repair complete?–System OK–

ZF 4 HP 16 AUTOMATIC TRANSAXLE 5A1 – 203
DAEWOO V–121 BL4
CONTROL VALVE BODY ASSEMBLY
Tools Required
DW260–070 Plug Remover/Installer
Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the transaxle wiring harness and the
park/neutral position switch electrical connector.
3. Raise and suitably support the vehicle.
4. Remove the engine under cover. Refer to Section
9N, Frame and Underbody.
5. Remove the transaxle fluid drain plug using the
plug remover/installer DW260–070 and drain the
transaxle fluid.
6. Remove the oil pan, oil pan gasket. Refer to ”Oil
Pan, Oil Pan Gasket” in this section.
7. Remove the valve body mounting bolts.
8. Remove the automatic transmission input speed
sensor mounting bolt.
9. Remove the automatic transmission output speed
sensor mounting bolt.

SECTION : 5A2
AISIN AUTOMATIC TRANSAXLE
CAUTION : Disconnect the negative battery cable before removing or installing any electrical unit or when a tool
or equipment could easily come in contact with exposed electrical erminals. Disconnecting this cable will help
prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise noted.
TABLE OF CONTENTS
SPECIFICATIONS5A2–3 . . . . . . . . . . . . . . . . . . . . . . . . .
General Specifications 5A2–3. . . . . . . . . . . . . . . . . . . .
Transaxle Gear Ratio 5A2–3. . . . . . . . . . . . . . . . . . . . . .
Fluid Capacity 5A2–3. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Line Pressure Specification 5A2–3. . . . . . . . . . . . . . . .
Fastener Tightening Specifications 5A2–4. . . . . . . . . .
SPECIAL TOOLS5A2–5 . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Tools Table 5A2–5. . . . . . . . . . . . . . . . . . . . . . .
SCHEMATIC DIAGRAMS5A2–8 . . . . . . . . . . . . . . . . . . .
Transmission Control Module (1 of 4) 5A2–8. . . . . . . .
Transmission Control Module (2 of 4) 5A2–9. . . . . . . .
Transmission Control Module (3 of 4) 5A2–10. . . . . . .
Transmission Control Module (4 of 4) 5A2–11. . . . . . .
Shift Mode Diagram 5A2–12. . . . . . . . . . . . . . . . . . . . . .
COMPONENT LOCATOR5A2–17 . . . . . . . . . . . . . . . . . .
Shift Select Control 5A2–17. . . . . . . . . . . . . . . . . . . . . .
Automatic Transaxle Components 5A2–18. . . . . . . . .
Bearing and Races Installation Position
Direction 5A2–24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS5A2–25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Connector View 5A2–25. . . . . . . . . . . . . . . . .
Wiring Harness and Connector Inspection 5A2–27. . .
Road Test 5A2–27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Function Check 5A2–28. . . . . . . . . . . . . . . . . . . . . . . . . .
Unit Inspection 5A2–30. . . . . . . . . . . . . . . . . . . . . . . . . .
On–Vehicle Repair (Matrix Chart) 5A2–34. . . . . . . . . .
DIAGNOSIS TROUBLE CODE DIAGNOSIS5A2–36 .
Diagnosis Trouble Code Chart 5A2–36. . . . . . . . . . . . .
DTC P0562 System Voltage Low 5A2–37. . . . . . . . . .
DTC P0563 System Voltage High 5A2–40. . . . . . . . . .
DTC P0601 Internal Control Module Memory
Checksum Error 5A2–43. . . . . . . . . . . . . . . . . . . . . . .
DTC P0604 Internal Transmission Control Module
(TCM) Random Access Memory (RAM)
Error 5A2–45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DTC P0705 Transmission Range (TR) Switch
Circuit Malfunction 5A2–47. . . . . . . . . . . . . . . . . . . . .
DTC P0712 Transmission Fluid Temperature
(TFT) Sensor Circuit Low Input 5A2–50. . . . . . . . . .
DTC P0713 Transmission Fluid Temperature
(TFT) Sensor Circuit High Input 5A2–53. . . . . . . . . .
DTC P0717 Input Shaft Speed (ISS) Sensor
Circuit No Signal 5A2–56. . . . . . . . . . . . . . . . . . . . . . .
DTC P0722 Ouput Shaft Speed (OSS) Sensor
Circuit No Signal 5A2–59. . . . . . . . . . . . . . . . . . . . . . .
DTC P0727 Engine Speed Input Circuit No
Signal 5A2–62. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0741 Torque Converter Clutch (TCC)
Circuit Stuck Off 5A2–65. . . . . . . . . . . . . . . . . . . . . . .
DTC P0742 Torque Converter Clutch (TCC)
Circuit Stuck On 5A2–67. . . . . . . . . . . . . . . . . . . . . . .
DTC P0743 Torque Converter Clutch (TCC)
Electrical 5A2–69. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0748 Pressure Control Solenoid (PCS)
Electrical 5A2–72. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0751 Shift Solenoid 1 (SS1) Stuck Off 5A2–75
DTC P0753 Shift Solenoid 1 (SS1) Electrical 5A2–77
DTC P0756 Shift Solenoid 2 (SS2) Stuck Off 5A2–80
DTC P0758 Shift Solenoid 2 (SS2) Electrical 5A2–82
DTC P0785 Timing Solenoid (ST) Electrical 5A2–85.
DTC P1781 Engine Torque Signal Error 5A2–88. . . . .
DTC P1791 Throttle Position Signal Error 5A2–91. . .
DTC P1792 Engine Coolant Temperature (ECT)
Signal Error 5A2–93. . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC U2105 Can Error 5A2–95. . . . . . . . . . . . . . . . . . . .
MAINTENANCE AND REPAIR5A2–97 . . . . . . . . . . . . .
ON–VEHICLE SERVICE 5A2–97. . . . . . . . . . . . . . . . . . .
Transaxle Fluid Level Checking Procedure 5A2–97. .
Fluid Drain Procedure 5A2–97. . . . . . . . . . . . . . . . . . . .
Locating Fluid Leaks 5A2–98. . . . . . . . . . . . . . . . . . . . .
Case Porosity Repair 5A2–98. . . . . . . . . . . . . . . . . . . . .
Fluid Cooler Flushing 5A2–99. . . . . . . . . . . . . . . . . . . . .
Control Cable Adjustment 5A2–99. . . . . . . . . . . . . . . . .

5A2 – 2IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
Shift Control Lever Assembly 5A2–100. . . . . . . . . . . . .
Transmission Range (TR) Switch 5A2–101. . . . . . . . .
Shift Control Cable 5A2–104. . . . . . . . . . . . . . . . . . . . . .
Shift Select Cover 5A2–105. . . . . . . . . . . . . . . . . . . . . .
Input Shaft Speed (ISS) Sensor 5A2–106. . . . . . . . . .
Output Shaft Speed (OSS) Sensor 5A2–107. . . . . . . .
Transmission Control Module (TCM) 5A2–108. . . . . .
Fluid Cooler Inlet Pipes and Hoses 5A2–109. . . . . . . .
Fluid Cooler Outlet Pipes and Hoses 5A2–110. . . . . .
Transaxle Assembly 5A2–111. . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR 5A2–117. . . . . . . . . . . . . . . . . . . . . . . . . . .
Major Component Disassembly 5A2–117. . . . . . . . . . .
Major Component Assembly 5A2–137. . . . . . . . . . . . .
Oil Pump 5A2–167. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Direct Clutch 5A2–171. . . . . . . . . . . . . . . . . . . . . . . . . . .
Planetary Ring Gear 5A2–178. . . . . . . . . . . . . . . . . . . .
One–Way Clutch 5A2–180. . . . . . . . . . . . . . . . . . . . . . .
Forward and Reverse Clutch 5A2–183. . . . . . . . . . . . .
Counter Driven Gear 5A2–192. . . . . . . . . . . . . . . . . . . .
Valve Body 5A2–195. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential Case 5A2–208. . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION AND SYSTEM
OPERATION5A2–218 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transaxle Description 5A2–218. . . . . . . . . . . . . . . . . . .
Electronical Components 5A2–218. . . . . . . . . . . . . . . .
Hydraulic Control System 5A2–221. . . . . . . . . . . . . . . .
Automatic Transaxle System 5A2–222. . . . . . . . . . . . .

5A2 – 4IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
FASTENER TIGHTENING SPECIFICATIONS
ApplicationNSmLb–FtLb–In
Drain Plug1713–
Control Cable Adjusting Nut8–71
Shift Control Lever Assembly Mounting Bolts8–71
Manual Valve Lever Shaft Nut12–106
Transmission Range (TR) Switch Bolts5.4–48
Input Speed Sensor Retaining Bolt5.4–48
Output Speed Sensor Retaining Bolt7.4–65
TCM Retaining Bolts5–44
Fluid Cooler Inlet Pipe Fitting Nut3526–
Fluid Cooler Inlet Pipe Bolt9–80
Inlet Pipe Union Bolt3526–
Fluid Cooler Rear Outlet Pipe Fitting Nut3526–
Fluid Cooler Rear Outlet Pipe Clip Bolt9–80
Front Outlet Pipe Union Bolt3526–
Lower Transaxle–to–Engine Retaining Bolts (a)7354–
Lower Transaxle–to–Engine Retaining Bolts (b)3123–
Lower Transaxle–to–Engine Retaining Bolts (c)2115–
Upper Transaxle–to–Engine Mounting Bolts7354–
Upper Transaxle Mounting Bracket Bolts6044–
Rear Mounting Bracket Bolts6044–
Damping Block Connection Nut and Bolt8059–
Torque Converter Bolts4543–
Screw Plugs7.4–65
Transaxle Apply Clamp Bolt5.4–48
Oil Reservoir Lock Plate Bolts5.4–48
Transaxle Case Plate Bolt9.8–87
Transaxle Housing Bolts2922–
Manual Detent Spring Bolt9.8–87
Parking Lock Pawl Bracket Bolts7.4–65
Planetary Ring Gear Nut (Standard)9.8–87
Planetary Ring Gear Nut (Maximum)2922–
Transaxle Rear Cover Bolts2518–
Oil Pump Bolts2518–
Valve Body Bolts11–97
Oil Strainer Bolts9.8–87
Oil Pan Bolts7–62
Unions2518–
Stator Shaft Bolts2518–
Shift Solenoid Valve Bolts11–97
Differential Case–to–Differential Ring Gear Bolt10275–

5A2 – 26IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
X–1 : TCM Vehicle Side Wiring Connector
A1GroundB1R
A2Pressure Control Solenoid GroundB3Clock
A4Pressure Control SolenoidB4Hold
A5Lock–Up SolenoidB6Input Speed Sensor
A6Ignition (+)B7D
A7CAN (Low)B8N
A11Transmission Fluid Temperature SensorB16Input Speed Sensor Ground
A12Transmission Fluid Temperature Sensor
GroundB18L
A14Timing SolenoidB192
A15Shift Solenoid No.2B20P
A16Shift Solenoid No.1B22Stop Lamp Switch
A17CAN (High)B23DLC
A23GroundB25Output Speed Sensor
A24B+––
X–2 : Transmission Range (TR) Switch Connector
1P
2R
3Ground
42
5N
6ST(–)
7D
81
9ST(+)
X–4 : Output Speed Sensor Connector
1Ignition
2Ground
3Output Speed Sensor
X–3 : Transaxle Wiring Connector
1Transmission Fluid Temperature Sensor
2Timing Solenoid
3Pressure Control Solenoid
4Lock–Up Solenoid
5Shift Solenoid No.1
6Transmission Fluid Temperature Sensor
Ground
8Pressure Control Solenoid Ground
10Shift Solenoid No.2
X–5 : Input Speed Sensor
1Input Speed Sensor Ground
2Input Speed Sensor

AISIN AUTOMATIC TRANSAXLE 5A2 – 31
DAEWOO V–121 BL4
Input Speed Sensor
S Inspect resistance of each input speed senor be-
tween terminals.
Notice :
S Make sure to inspect resistance again at 20°C
(68°F) when resistance differ from standards ex-
cept 20°C (68°F).
S It might become infinity ohm when inspect resist-
ance at higher temperature.
Action : If the result of inspection is bad, replace ISS.
Transmission Range (TR) Switch
S Remove TR switch connector and inspect continuty
each range according to the conection chart.
Action : If the result of inspection is bad, replace the TR
switch.
Transmission Fluid Temperature Sensor
S Inspect the resistance between the terminals of
TFT sensor at 10°C (50°F) and 110°C (230°F).
Standard Value
10°C (50°F)11 0°C (230°F)
5.80~7.09 kΩ0.23~0.263 kΩ
Action : If the result of inspection is bad, replace the TFT
sensor.

5A2 – 36IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE DIAGNOSIS
DIAGNOSTIC TROUBLE CODE CHART
DTCDESCRIPTIONTYPEIlluminate
MILBlink
Hold
Lamp
P0562System Voltage LowBYe sNo
P0563System Voltage HighBYe sNo
P0601Internal Control Module Memory Checksum ErrorAYe sNo
P0604Internal Transmission Control Module (TCM) Random Access
Memory (RAM) ErrorBYe sNo
P0705Transmission Range (TR) Switch Circuit MalfunctionBYe sNo
P0712Transmission Fluid Temperature Sensor Circuit Low InputAYe sNo
P0713Transmission Fluid Temperature Sensor Circuit High InputAYe sNo
P0717Input Shaft Speed (ISS) Sensor Circuit No SignalAYe sNo
P0722Output Shaft Speed (OSS) sensor Circuit No SignalAYe sNo
P0727Engine Speed Input Circuit No SignalAYe sNo
P0741Torque Converter Clutch (TCC) Circuit Stuck OffBYe sNo
P0742Torque Converter Clutch (TCC) Circuit Stuck OnBYe sNo
P0743Torque Converter Clutch (TCC) ElectricalBYe sNo
P0748Pressure Control Solenoid (PCS) ElectricalAYe sNo
P0751Shift Solenoid 1 (SS1) Stuck OffBYe sNo
P0753Shift Solenoid 1 (SS1) ElectricalAYe sNo
P0756Shift Solenoid 2 (SS2) Stuck OffBYe sNo
P0758Shift Solenoid 2 (SS2) ElectricalAYe sNo
P0785Timing Solenoid (ST) ElectricalAYe sNo
P1781Engine Torque Signal ErrorAYe sNo
P1791Throttle Position Signal ErrorAYe sNo
P1792Engine Coolant Temperature (ECT) Signal ErrorDNoNo
U2105CAN ErrorAYe sNo
* Description of Type
S Type A : TCM will request the illumination of MIL and store DTC when TCM detects a failure on the first ignition
cycle.
S Type B : TCM will request the illumination of MIL and store DTC when TCM detects failures on two consecutive
ignition cycle.
S Type D : TCM will not request the illumination of MIL or hold lamp, but will store DTC when TCM detects a failure
on the first ignition cycle.