2004 DACIA SUPERNOVA check engine light

82A
HORN - ENGINE IMMOBILISER
82A - 14
7. Set the contact in “M” position with one of the keys (without starting the engine), for about
2 seconds and then check the following states, which must be:
9D RECEIVED KEY CODE………………………………………. ACTIVE
19G NOT PERFORMED KEY PROGRAMMING ……………… ACTIVE
8. Set the contact with the second key (without starting the engine) for about 2 seconds.
Check then the following states:
-case (a)- the second key belongs to the vehicle;9D RECEIVED KEY CODE………………………………………. ACTIVE
19G NOT PERFORMED KEY PROGRAMMING……………… PASSIVE
- case (b)- the second key does not belong to the vehicle or the first key was used once again;
9D RECEIVED KEY CODE………………………………………PASSIVE
19G NOT PERFORMED KEY PROGRAMMING……………… ACTIVE
9. The anti starting indicator blinks rapidly.
10. Take off the contact. In t he menu “COMMAND MODE” select “ACTUATORS” and
validate “ FINISHED CALIBRATION” launching the command on the blue rectangle situated
on the right top of the screen. The message “COMMAND IN PROGRESS” will appear,
followed by “ FINISHED COMMAND”. 11 . The anti starting indicator will blink rarely.
12. Get back to the “ STAT E LIST”, which now must be as follows: 18G FIRST CYCLE MEMORISING……………………………... ACTIVE
19G NOT PERFORMED KEY PROGRAMMING……………… PASSIVE
19D UNLOCKED KEY PROGRAMMING………………………PASSIVE
13. In the m enu “COMMAND MODE” choose “ ACTUATORS”. Select the command “
FORCED PROTECTION MODE” launching the command from the blue button situated on
the ri ght topside of the screen. The display will show “COMMAND IN PROGRESS” and
then “FINISHED COMMAND”. Get back to t he “STATE LIST “ and check the state:
9G FORCED PROTECTION MODE …………………………….. ACTIVE
14. Set the contact on “M” position. The anti starting indicator will start to blink rapidly. Check
in the “ STATE LIST” if the state “ANTI STARTING” is “ACTIVE”.
15. In the menu “COMMAND MODE” access “ACTUA TORS”, then select the command “
MANUAL INTRODUCTI ON CODE”. Type the four figures of the repairing code, then validate
with the key “ENTER”. On the screen the message “COMMAND IN PROGRESS” will
appear and then “FINISHED COMMAND”. 16. Take off and then set again the contact, without starting the engine, in order to send the
new anti starting code to the injection computer. The anti starting indicator will light for 3 seconds,
and then it will turn off.
17. The procedure is finished. Check the engine starting with both keys. PROCEDURES
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 16
D. SIMPLE S
YNCHRONISED PROCEDURE
This procedure allows the synchronisation of a RF remote control with E.C.U. decoder and
is to be applied in the following situations:
- the RF remote control c ode is no longer i n the range of the E.C.U. decoder re ception,
because of consecutive pushing over a 1000 time on the RF remote control button.;
- the replacement of the E.C.U. decoder with a new one;
- the replacement of the RF remote control if the E.C.U. decoder is new (E.C.U. decoder
replacement plus a RF key.)
The following operations will be performed: - take off t he contact
- push and maintain like that for about 5 seconds, the doors locking switch located on the
dashboard ; the doors actuators are performing a closing/opening course.
- during the next 10 seconds, confirmed by the permanent lightening of the anti starting
system indicator, push twice the RF remote control button; the doors actuators are performing a
closing/o pening course.
- the procedure of synchronisation is finished; check the blocking/ unlocking by pushing
the RF remote control.
OBSERVAT ION
Duri ng those 10 seconds you can visualise by means of the CLIP tester the state 17G
“THE PROGRAMMING IN PROGRESS OR THE TIR/TRF
RESYNCHRONISATION” which must be ACTIVE.
E. SPECIFIC SYNCHRONISED PROCEDURE
This procedure is used for the synchronisation of the second RF key with E .C.U. decoder
and will be performed as follows:
- connect the CLIP tester to the diagnostic socket and the battery (or the lighter socket) of
the vehicle. - select the vehicle type “SUPERNOVA” and the “050” equipping level;
- select the m enu “ COMPUTERS TEST” then “ ANTI STARTING”
- enter the m enu “COMMAND MODE” and select “CONFIGURATION”
- validate the command “ PROGRAMMI NG THE SECOND TIR / TRF KEY” launching
the command from the blue button situated on the right top of the screen; the doors actuators are
performing a closing/opening course.
- during the next 10 seconds, confirmed by the permanent lightening of the anti starting
system, push twice the RF remote control button; the doors will block and then unlock and the
anti starting indicator will t urn off. The second remote control is now synchronised. Check the
blocking/ unlocking by pushing the RF remote control. PROCEDURES
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 20
D)
Memorising of the new code of the injection computer
- in ACTUATORS
launch the command MANUAL INTRODUCTION CODE ; type
the repairing code of the old key kit, then validate it with the key
ENTER.
- the message “COMMAND IN PROGRESS ” will be displayed followed by the message
“FINISHED COMMAND ”.
-s et the contact on; t he anti starting LED indicator will start blinking, then take off the
contact;
-set the c ontact on for 10 seconds ; take off the contact;
- check if the engine starts with the two keys.
If the engine doesn’t start, repeat this operation (point D).
E) Key resynchronisation (remote controls)
-if the vehicle is equipped with only one remote control, its resynchronisation will be
performed as follows (simple resynchronisation);
- with t he contact taken off, push continuously on the c entra l l ocking but ton from the
dashboard, up to the moment the anti starting LED indicator remains lighted (the doors actuators
are performing a closing/opening course.) From this moment, t he operator has 10 seconds to
perform the next operation; - push twice on the remote control (the doors actuators are performing a closing/opening
course.) and the anti starting LED indicator turns off; - if the vehicle is equipped with two remotes controls, perform the simple resynchronisatio n
procedure for the first key and a specific resynchronisation procedure for the second key, with
the CLIP tester as follows: - in COMPUTER TEST select ANTISTARTING with t he c ontact t aken off, then
COMMAND MODE , CONFIGURATION ; launch the command PROGRAMMING OF
THE SECOND TIR/TIE KEY and validate (the doors actuators are performing a closing/
opening course.). Then within 10 seconds, push twice on the remote control (the doors actuators
are performing a closing/o pening course).DIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 32
ALP3. THE ANTI STARTING INDICATOR REMAINS PERMANENTLY LIGHTED
(even when the contact is taken off) OR IT REMAINS PERMANENTLY SWITCHE D OFF.
RECOMMENDATIONCheck if the “Procedure E.C.U. decoder replacement” was correctly
performed.
Check the fuse F15 ( up to 01.06.2001) or
F07 (after 01.06.2001).
Is the fuse good?
Is there the failure “ DOORS’ LOCKING
CONTACT”?
Check the continuity and the isolation related
to the ground, between t he pin A 5 of the
E.C.U. decoder and the dashboard.
Is the wiring good?
Replace the fuse.
Analyse this failure and replace.
Fix the wiring.
Perform the following tests in order to find the
failure element:
- if the anti starting indicator is permanently
lighted, disconnect the connector of the E.C.U.
decoder and check if the indicator switches off;
- if the anti starting system is turned off,
c onnect the pin A5 of the wiring connector from
the E.C.U. decoder to an electric ground and
check if the indicator turns on.
Are the answers affirmatives?
Replace the instrument panel.
Replace the E .C.U. decoder.
Perform a conformity checking.
AFTER REPAIRING Check the operation of the anti starting system. Remove by means of the CLIP tester the possibl e memorised failures.
No
No
No
Yes
Yes
No
Yes
YesDIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 37
A
LP8. TURNING LIGHTS DO NOT SWITCH ON AT THE BLOCKING /
UNLOCKING OF THE DOORS
RECOMMENDATION Check the absence of the failures with the CLIP tester.
If there are failures, fix them first.
Check if the synchronisatio n of the RF remote control and the E.C.U. decoder has been performed .
Are the turning lights functioning normally at the activation of the signalling switch ?
Check the continuity and the isolation related to
the ground and the +12 V of the electric layout:
E.C.U. decoder FLASH relay
Pin B3 pole 2
Is it correct?
Repair the signalli ng system.
Check t he fuse F03 and F04.
Fix the electric layout.
Check the fuse F15 ( up to 01.06.2001) or
F 07 (after 01.06.2001).
Is it good?Replace the fuse.
Disconnect the FLASH relay. Supply with
+ 12, the pole 4 of the relay. Are the l eft
turning lights turning on? Supply with +12 V
the pole 5 of the signal relay.
Are the right turning lights turning on?
Repair the electric layout from
poles 4 and 5 of the FLASH relay.
Replace the FLASH relay.
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
No
No
No
Yes
Yes
Yes
Yes No
DIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 38
No
AFTER REPAIRING Perform a conformity
checking.
Check the operation of the anti starting system.
A LP9. THE CEILING LAMP DOES NOT SWITCH ON AT THE BLO CKING /
UNLOCKING OF THE DOORS OR IT REMAINS PERMANENTLY TURNED ON.
RECOMMENDATION Check the absence of failures with the CLIP tester.
If there are memorised failures, fix them first.
Check if t he doors are locked?
Has the ceiling lamp turned on? The ceiling lamp was in the
position “p
ermanently
lighting”. Normal
operation.Yes Yes
Unlock the doors with the RF remote control.
The ceiling is in the position “dome lighting”
Has the ceiling lamp turned on?
Check the isolation of the wiring
related to the ground on the line pinA1.
decoder ceiling
After 15 seconds, the ceiling lamp will
turn off.
Normal operation.
Was the E.C.U. decoder confi gured “With
dome ceiling ”?Configure the E.C.U. decoder with
the CLIP tester.
Check the continuity on the line
E. C.U. decoder pin A1 ceiling
Is the line good?Repair .
Check the ceiling lamp bulb.
No
No
No
Yes
Yes Yes
No
DIAGNOSTIC
vnx.su

82B
HORN - ENGINE IMMOBILISER
82B - 45
Vo l u m etric protection checking.
Perform the following checking steps after locking using the RF remote control, the doors, the
engine hood and the hatchback. The operations must be performed in no more than 40 seconds
since the anti i ntrusion system has been activated with the RF remote control; if operating after
these 40 seconds, the siren will start and the turning lights will blink.
Close the door. The sound signal (buzzer)
will stop.
Th e pr oper operation of the anti intrusion system on different situations must be according to
those shown in Table 01. For detecting the causes of possible incidents of the anti intrusion system, perform the checking
steps presented in Table 02.
Lo wer the rear windows with about 10
cm. Close the doors, the engine hood
and the ha tchback.
Check out if there is any movement in
the cockpit.
Ac tivate the system pressing the button
of the RF remote control.
In troduce a hand through the window,
inside the cockpit and move it.
Th e LED indicator will blink quickly,
showing there has been a volumetric
detection and that volumetric sensors are
f unctioning correctly.
Deac tivate the system using the RF
remote contro l, then clos e al l the
vehicle windows.
Reactivate the system and then hit by
ha nd the windows surfa c e of the
vehicle. The LED indicator should
continue to normally blink and the siren
starting shall not occur.
Functional checking of the peripheral
protection.
Close the doors, the engine hood and the
hatchback.
Ac tivate the system pressing the button
of th e RF remote.
The doors will lock and the LED indicator
will blink.
Open a do or with the vehicle key.
The LED indicator will continuously be on,
a nd a sound signal (buzzer) will be heard.
Deac tivate and reactivate the sys tem
w ith the RF remote control.
Deac tivate t he system by pressing the
button of the RF remote control.
The do ors will unlock and t he LED
indicator will go off.
Rep eat a.m. operations for both front
door s, engine hood and hatchback.
FUNCTIONAL CHECKING OF THE SYSTEM
vnx.su

83
INSTRUMENT PANEL
OIL PRESSURE WARNING LIGHT STILL ON
AFTER ENGINE STARTING
Check the oil pressure
The pressure is correct.
Replace the oil pressure switch. The pressure is not correct.
There is a failure in the oil circuit.
OIL PRESSURE WARNING LIGHT IS NOT ON
WHEN CONTACT SWITCH ON
Place the wire from the oil pressure switch to the ground.
Wa r ning light is not on.
Check if the bulb is not burnt.
Warning light is on. Replace the oil pressure
switch.
Burnt bulb. Replace it. Bulb is not burnt . Check the bulb
supply wiring and fix it.
FUEL LEVEL INDICATOR
SHOWING ALWAYS FULL
Disconnect the connection wire t o the probe.
The indicator comes back
to zero. Re place the probe. The indicator
does not come to zero.Is there
any ground short-circuit of the connection
wi re to the probe?
Yes. Fix the wiring layout. No. Replace the indicator.
83-7
DIAGNOSTIC
vnx.su