2004 DACIA SOLENZA rims

GENERAL
30 - 17
30Angles checking principle
PRELIMINARY CHECKING
Before starting the steering angles checking, it will be necessary to check the following points
and exclude the possible non-conformities.
1. Tires and rims checking, regarding: - type and dimension;
- inflating pressure;
- wear de gree.
2. Joints : - elastic bearings and bushings condition;
- ball joints clearance;
- bearing clearance;
- steering wheel column clearance.
3. Tires runout and axial runout (compensation is to be performed by means of the reading
instruments);
4. Dimensions symmetry under carriage body (suspension condition).
5. Manufacturer’s method : each vehicle manufactu rer is prescribing the checking conditions,
loading repartition on axles, under carriage body dimensions presentation.
vnx.su

35
WHEELS AND TIRES
35 - 1
Characteristics
WHEELS
The wheels identification marking is repre sented in two ways: -engraved marking for steel rims
- cast marking for aluminum rims
The marking enables acknowledgment of the main wheels dimensions criteria.
This marki ng may be:
- Complete Example : 5.5 J 14 4 CH 43 , or
- Simplified
Example: 5.5 J 14
The wheel attachment holes are situated on a diameter of 100 mm.
Maximum axial runout : to be measured in points P1 and P2.
Maximum radial runout : to be measured in points G1 and G2.
AB C D E F
Rim width Rim Rim nominal Number of Tire Offset
Rim type ( in inches) edge diameter attachment staffing ( in mm) profile (in inches) points profile
5.5 J 14 4CH 43 5.5 J 14 4 CH 43
5.5 B 13 4CH 46 5.5 B 13 4 CH 46
G1
P1P2
G2
vnx.su

WHEELS AND TIRES
35
35 - 4
Wheels balancing
BALANCING WEIGHTS
Use exclusively t he weights delivered as spare pa rts, with a ttachment by m eans of mass
incorporated clamps.
A = balancing weights for steel rims
B = balancing weights for aluminum alloy rims.
A
B
vnx.su

INSIDE ACCESSORIES
Dashboa rd .......................................................... 57-1
Inside rear view mirror ..................................... 57-8
S un visors ........................................................... 57-9
Central console ................................................. 57-10
Handbrake case ................................................ 57-11
Turning handle .................................................. 57-12
SECU RITY ELEMENTS
Fr ont safety belts ............................................... 59 - 1
Re ar safety belts ............................................... 59 - 2
HEATING
General .............................................................. 61-1
Operating principle ........................................... 61-2
C limate c ontrol unit .......................................... 61-4
Ve n t ilation- climate control air
distributor (RACV) .......................................... 61-5
Heating radiator ................................................ 61-6
C ontrol panel ..................................................... 61-7
C ontrol cable s ................................................... 61-9
Motor fan control resistance............................ 61-10
Diagnose ............................................................. 61-11
AIR CONDITIONING
General ............................................................... 62-1
Draining – filling the refrigerant circuit ......... 62-3
Air conditioning unit operating diagram ........ 62-4
Operating principle ........................................... 62-5
Part icles filter .................................................... 62-7
Cold ai r blowing device (DSAF) ...................... 62-8
Evaporator ........................................................ 62-10
Control panel ..................................................... 62-11
Comp ressor ........................................................ 62-12
C ondenser .......................................................... 62-13
Pressu re controller ............................................ 62-14
F ilter reser voir ................................................... 62-15
Unit piping ......................................................... 62-16
Thermostatic expansion valve ......................... 62-19
C limate c ontrol blower ..................................... 62-20
Blow er control resistance .................................. 62-21
Rec ycling flap motor fan ................................. 62-22
Diagnose ............................................................. 62-23
CARRIAGE BODY SEALING
Ca rriage body se aling ....................................... 64 - 1 OPENINGS SEALING
Opennings sealing ............................................. 65 - 1 GLASSES SEALING
Glasses gaskets .................................................. 66 - 1
Inside wipers ..................................................... 66 - 2
Outside wipers ................................................... 66 - 3
Fr ont door glass channel ................................. 66 - 4
Rear door gla ss run channel ............................ 66 - 5
CARRIAGE BODY INSIDE TRIMS
C arriage body inside trims ............................. 71-1
Upper front pillar trim ..................................... 71-2
Mi ddle pillar trim ............................................. 71-3
Rear quarter panel tr im ................................... 71-4
R oof lining ......................................................... 71-5
Trunk carpet ...................................................... 71-6
Cowl panel noise absor bent ............................. 71-7
Cockpit carpet ................................................... 71-8
LATERAL OPENINGS TRIMS
Fr ont door panel ................................................ 72-1
R ear door panel ................................................. 72-2
REAR TABLE
Lateral table ....................................................... 74-1 FRONT SEATS SLIDES GUIDES
Fr ont seat ........................................................... 75-1
Fr ont seats slides guide s ................................... 75-2
SEATS / R EAR BENCH
R ear bench ......................................................... 76-1
BATTERY - FRONT HEADLIGHTS
Battery ... ............................................................ 80-1
Headlamp assembly .......................................... 80-4
F og projectors ................................................... 80-5
Bulbs ... ................................................................ 80-6
Headlamps adjustment .................................... 80-9
Repl acement of the headlamps mechanic
adjustment control ........................................... 80-1157
Mechanisms and accesoires5
59
61
62
Climatisation6
64
65
66
71
72
74
75
76
80
Echuipment electr ique8
Garnishing and tack room7
vnx.su

71
CARRIAGE BODY INSIDE TRIMS
71 - 1
Carriage body inside trims
1 - Upper front pillar tri m
2 - Middle pillar t rim
3 - Rear quart er panel tri m
12 3
vnx.su

CARRIAGE BODY INSIDE TRIMS
71
71 - 2
DISMOUNTING
Dismount :
- dashboard upper part (see chapter 57 );
- front door sealing gasket in the contact area with the front pillar tri m;
- trim attachment screw (2) on the side fra me lining.
Upper front pillar trim
Detach from clips the upper front pillar trim (1) and release it.
REMOUNTING
Perform the dismounting operations in the reverse order.
The screw tightening moment is of 0,12 daNm.
1
2
vnx.su

71
CARRIAGE BODY INSIDE TRIMS
71 - 3
Middle pillar trim
DISMOUNTING
Move the front seat to e nable opera tor
access to the front pillar. Dismount:
- partially the front/re ar door ga skets
(in the contact are as with middle pi llar tri m);
- attachment screws (2) and (5) of the
front belt on the middle pillar at upper part,
consequently, at lower part;
- attachment screws (3) and (4) of the
middle pillar tri m on the side frame lining.
Release the middle pillar tri m (1).
REMOUNTING
Perform the dismounting ope rations in
the reverse order.
The tightening moment of the be lt attach-
ment screws is of 2,7 daNm, and the one of
the attachment screws of the middle pillar
trim is of 0,12 daNm.
vnx.su

CARRIAGE BODY INSIDE TRIMS
71
71 - 4
Rear quarter panel trim
DISMOUNTING
Dismount:
- rear quart er panel ornament;
- partially the rear door sealing gasket in the contact area with the rear quarter panel
trim; - rear table;
- table support ( see chapter 74);
- attachment screw (2) of the rear belt on the upper pa rt;
- attachment screws (4) and (5) of the rear quart er pa nel trim to t he side frame l ining.
Detach from clips the rear quarter pa nel trim (1).
REMOUNTING
Perform the dismounting operations in the reverse order.
The tightening moment of the belt attachment screw is of 2,7 daNm.
vnx.su