2004 DACIA SOLENZA ESP

IGNITION AND INJECTION
17
17 - 67
Diagnostic – Conformity checking
Sequence Function Parameter /Controlled state or action Visualization Diagnostic
and Observations
ET032 : Canister purging ACTIV E
1 C anister purging X > 1.5 % and vari ableNothing to be
PR023 : RCO canister purging noticed
valve
2S peed vehicle PR018 : Vehicle speed X = The spe ed red on In case of a problem
the speedometer consult the PR018
in Km/hour diagnostic
3 Detonation Vehicle in charge In case of a problem
se nsor PR013 : Detonation average X is variable consult the PR013
signal and different of 0 dia gnostic
PR 015 : Anti-detonation 0° < X < 7° RAC
correction.
4 Downstream PR010 : Oxygen sensor voltage Do not ta ke into
oxygen sensor c onside ration
voltage at idling
R unning in full charge The sensor is
showing
enriched mixture, Nothing to be
X is increasing with a notic e d
small responding time
At deceleration, after an The sensor is showing
acceleration with the pedal poor mixture,
fully pressed. X is decreasing with
a small responding
time.
RECOMMEND AT IONS The values show n on this conformity checking are only as indication.
Performing conditions : During a drive test
vnx.su

IGNITION AND INJECTION
17
17 - 81
AC010FUEL PUMP RELAY
RECOMMEND AT IONS No failure must be prese nt or memorized.
Before perform this checking, check the lines corresponde nce on the
electric diagram adequate to that vehic le.
Ch eck that choke sensor is in operating condition
M end the choke sensor if necessa ry.
Ch eck the continuity between ways 1 and 3 of the choke sensor.
If there is no continuity, repla ce the choke sensor.
Ch eck, under starter operation, the prese nce of the +12 volts at way 3 of t he choke sensor connector.
If there is no +12 volts, restore in function the line from way 3 of the choke sensor to pole 5 of the fuel
pump relay.
Ch eck the wiring condition and the mass presence at the fuel pump.
Ch eck the wiring insu lation and cont inuity :
Way 3 choke sensor > fuel pump
M end if necessary.
If the incident is persisting, repla ce the fuel pump.
Diagnostic – Parameters interpretation
AF TER Restart the conformity checking from the beginning.
REPARATION
vnx.su

IGNITION AND INJECTION
17
17 - 85
ALP 2 STARTING PROBLEMS engine is not starting or is difficulty starting)
RECOMMEND AT IONS Do not consult this diagnostic but before performing a complete
checking by means of the CLI P tester.
Ch eck that starter is well operating
Ch eck there is petrol in the fuel tank (fuel indicator failure).
Ensure that vehic le is supplied with adequate fuel.
Ch eck tha t supply cir cuit hoses are not broken (espe cially further to a dismounting)
Ch eck the condition of the fuel filter
Ch eck the condition of the fuel tank
Ch eck that fuel tank aeration is taking place.
Ch eck the electric supply of the fuel pump.
Ch eck the good operation of the choke sensor.
Ch eck the motor of the idling regula tor.
In order to unblock it, you may slightly hit it.
Disconnect the connection hose between the canister purging valve and the intake manifold.
Cl amp the connection hose in order to stop the air passing.
If there are no more disturbances, the cause is the canister purging valve.
Ch eck the spark plugs and ignition coil condition
Ch eck tha t these eleme nts are specific to that vehicle.
Ch eck that the exhaust route is not clogged and the catalyst is not clogged.
Ch eck the engine compressions
Ch eck the flywheel condition
Ch eck the distribution setting on.
AFTER Perform a checking by means of the CLI P tester.
REPARATION
Fa ilure locating algorithm
vnx.su

IGNITION AND INJECTION
17
17 - 86
ALP 3 IDLING PROBLEMS (unstable idling)
RECOMMEND AT IONS Do not consult this diagnostic but before performing a complete
checking by means of the CLI P tester.
C heck if there is petrol in the fuel tank (fuel indicator failure)
C heck if the vehic le is supplied with adequate fuel
C heck tha t supply cir cuit hoses are not broken (espe cially further to a dismounting)
C heck the condition of the fuel filter
C heck the condition of the fuel tank
C heck that fuel tank aeration is taking place.
C heck the connection and the condition of the idling regulator connector.
Re place the connector if necessary.
C heck the motor of the idling regulator
In order to unblock it, you may slightly hit it.
Disconnect the connection hose between the canister purging valve and the intake manifold.
Cl amp the connection hose in order to stop the air passing.
If there are no more disturbances, the cause is the canister purging valve.
C heck the spark plugs and ignition coil condition
C heck tha t these eleme nts are specific to that vehicle.
C heck that the exhaust route is not clogged and the catalyst is not clogged.
Check, by means of the oil dipstick, that oil level is not too high.
C heck for lack of sealing at servo-brake (noise).
C heck the intake manifold condition
C heck if the valve body is not clogged
C heck the engine compressions.
C heck the engine flywheel condition
C heck the distribution setting on.
AFTER Perform a checking by means of the CLI P tester.
REPARATION
Fa ilure locating algorithm
vnx.su

IGNITION AND INJECTION
17
17 - 87
ALP 4 INTEMP ERATE ACCELERATION OR DECELERATION
(engine unstable running)
RECOMMEND AT IONS Do not consult this diagnostic but before a complete checking by
means of the CLIP tester
Ch eck if air filter is not deformed.
Ch eck if there is petrol in the fuel tank (fuel indicator failure)
Ch eck if the vehic le is supplied with adequate fuel
Ch eck tha t supply cir cuit hoses are not broken (espe cially further to a dismounting)
Ch eck the condition of the fuel filter
Ch eck the condition of the fuel tank
Ch eck that fuel tank aeration is taking place.
Disconnect the connection hose between the canister purging valve and the intake manifold.
Cl amp the connection hose in order to stop the air passing.
If there are no more disturbances, the cause is the canister purging valve.
Ch eck the spark plugs and ignition coil condition
Ch eck tha t these eleme nts are specific to that vehicle.
Ch eck that the exhaust route is not clogged and the catalyst is not clogged.
Ch eck the se aling of the exhaust manifold.
Ch eck, by means of the oil dipstick, that oil level is not too high.
Ch eck for lack of sealing at servo-brake (noise).
Ch eck the intake manifold condition
Ch eck if the valve body is not clogged
Ch eck the engine compressions.
Ch eck tha t brake calipers, drums and bearings are not gripped.
Ch eck that tires are inflated
Ch eck the engine flywheel condition
Ch eck tha t cooling system is properly operating
AFTER Perform a checking by means of the CLI P tester.
REPARATION
Fa ilure locating algorithm
vnx.su

19
19 - 7
COOLING - EXHAUST - TANK
Cooling engine fan for vehicles without air conditioning
DISMOUNTIN G
Disconnect the battery (-) terminal.
Remove the air inlet pipe from the attachment of the battery screen.
Detach from clips the oil reservoir of the power steering from the battery screen.
Disconnect the engine fan connector ( 1) and detach from clips wiring of point ( 2)
Dismount the four attachment screws ( 3) of the engine fan on radiator.
Carefully dismount the engine fan assembly from guiding points (4).
REMOUNTING
Check the condition of the fan impeller and of the engine fan electric motor.
Carefully position the engine fan assembly in the guiding points (4).
Mount the attachment screws ( 3) of the assembly on the radiator.
Connect the engine fan connector ( 1).
Attach in clips the wiring in point ( 2).
Attach in clips the power steering oil reservoir on the battery screen.
Mount the air inlet pipe.
Connect t he battery (-) terminal. In case the vehicle is equipped with programmable
r adio-cassettes player, e lectronic clock, etc, there are t o be re-programmed before returning
the vehicle to the client.
Check the engine fan operation: start the vehicle engine and disconnect the water
temperature sensor. The engine fan must start. Reconnect the water temperature sensor
then by means of the CLIP tester erase the memorized failure corresponding to the water
temperature sensor.
vnx.su

19
19 - 9
COOLING - EXHAUST - TANK
Cooling engine fan for vehicles with air conditioning
DISMOUNTIN G
Disconnect the battery (-) terminal.
Remove the air inlet pipe from the attachment of the battery screen.
Detach from clip the power steering oil reservoir from the battery screen.
Disconnect the engine fan connector ( 1)
Detach wiring from clips ( 2) and (3).
Disconnect the connector of the cooling engine fan resistance (4).
Carefully dismount the engine fan assembly from the radiator, from sustaining points (5).
REMOUNTING
Check the condition of the fan impeller and of the engine fan electric motor.
Carefully mount the engine fan assembly in the sustaining points (5).
Connect the connector of the engine fan resistance ( 4).
Connect the cooling engine fan connector ( 1) and attach it in clip (3) then in clip (2).
Attach in clips the power steering oil reservoir on the battery screen. Mount the air inlet
pipe.
Connect the battery (-) terminal. In case the vehicle is equipped with programmable
r adio-cassettes player, electronic clock, etc, there are t o be re-programmed before returning
the vehicle to the client. Check the engine fan operation: start the vehicle engine and disconnect the water
temperature sensor. The engine fan must start. Reconnect the water temperature sensor
then by means of the CLIP tester erase the memorized failure corresponding to the water
temperature sensor.
vnx.su

19
19 - 23
COOLING - EXHAUST - TANKFuel pump
VEHICLES WI THOUT VISITING CAP
SPECIAL TOOLS
MOT 1397 Wrench for pump assembly dismounting- remounting
TIGHTENING MOMENTS (daNm)
Fuel tank attachment screws 2.1
Pump assembly attachment nut 7
In order to dismount the fuel p ump as-
sembly, it is n eces s ary th e fuel tank dis-
mounting.
IMPORTANT
Duri ng this operation it is compulsory:
-n ot smoking and not approaching
with inca ndescent objects in the working
area, - keep away from fuel spraying when
disconnecting the fuel connections, -protect the sensitive area of fuel leak.
DISMOUNTIN G
Dismount the fuel tank.
Dismount the attachme nt nut of the fuel pump
assembly by means of the wrench MOT 1397.
Dismount the fuel pump assembly
AT T E N T I O N !
When dismounting the nut, take c are that
fuel pump assembly i s not geared in rotation
with t he nut, which may lead to float rod
di st ortion and c onseque ntly t o fuel l evel
wrong indication.
Remark:
If until fuel pump mounting on t ank,
more than an hou r is taken in to
consideration, remount the nut on t he
tank, in order to avoid any distortion.
R EMOU NT I NG
Replace the sealing gasket of the fuel
pump assembly. The gasket shall have the
same color with the dismounted one. Mount the fuel pump assembly so that
arrow (1) from t he fuel pump assembly i s
corresponding to the arrow (20 from the
tank.
Position the nut and tighten it by hand to
maximum possible, pre venting t he pum p
assembly rotation.
Tighten the nut by m eans of the MOT
1397 wrench until arrow (3) from the nut is
aligned with the marks from fuel tank a nd
pump assembly .
2
3 1
vnx.su