2004 Citroen C3 level

Downloaded from www.Manualslib.com manuals search engine 316
CLUTCH
GEARBOX
TRANSMISSION
MA/5 PILOTED MANUAL GEARBOX
Engines: KFV 8HX
Features.
The piloted gearbox is a modern manual gearbox with technology that offers
enhancements in every driving situation.
The piloted manual gearbox has two operating programmes:

«Sequential»programme.
«Automatic»programme.
The piloted manual gearbox has:
A gearbox ECU
(supplier:SIEMENS). A gearbox actuator with two electric motors (supplier:SACHS).
A clutch actuator with one electric motor (supplier:SACHS).
A gearbox input speed sensor.
The piloted manual gearbox has no gear control cable and no clutch cable.Changes of gear and clutching/declutching are activated by the gearbox
actuator and the clutch actuator.
Lubrication.
Oil capacity : 2 ± 0,15 litres.
Checking of oil level : No oil level check.(*)Lubrication intervals : Lubricated «for life».
(*)= Only a visual check of the sealing at each engine oil change interval.
B2CP3SUD
C2

Downloaded from www.Manualslib.com manuals search engine 331
CLUTCH
GEARBOX
TRANSMISSION
RECOMMENDATIONS PRECAUTIONS: AL4 AUTOMATIC GEARBOX
Engines: KFV NFU RFN RHZ
If a gearbox malfunction occurs, there are two possible
configurations depending on the seriousness of the fault:
Gearbox in backup mode with a replacement programme of
(the
fault values are taken in substitution).
Gearbox in backup mode with an emergency programme (3rd
hydraulic).WARNING:In the emergency programme, an impact is felt
when changing P/R, N/R and N/D.
Réception client.
Discuss with the customer, to find out all the malfunction symptoms.Oil quality Oil level.
Oil quality.
If the gearbox has suffered a serious fault resulting in a malfunction
or the destruction of a clutch, the oil will overheat and become
contaminated with impurities: the oil is said to be
«burnt».
This is characterised by a black colour and the presence of an
unpleasant smell.
ESSENTIAL: The gearbox must be replaced.
Oil level (see corresponding operation).
An excessive oil level can result in the following consequences:
Excessive heating of the oil.
Oil leaks.
An insufficent level causes the destruction of the gearbox.
Top up the level of oil in the gearbox (if necessary).
Check using a diagnostic tool.
Read the fault codes
(engine and gearbox).
Absence of fault codes.Carry out parameter measures, actuator tests and a road test.
Presence of fault codes.Carry out the necessary repairs.
Delete the fault codes.
Carry out a road test to check the repair and, if need be, modify the
gearbox ECU parameters
(this is essential after an initialisation
of the ECU).
XSARA XSARA PICASSO
Procedure to be followed prior to carrying out repairs on AL4 autoactive gearbox

Downloaded from www.Manualslib.com manuals search engine 337
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
Tightening torques (m.daN).
(1)
Oil flow modulation electrovalve fixing: 1 ± 0,2
(2)
Heat exchanger fixing:5 ±1
(3)
Output speed sensor fixing:1 ±0,2
(4)
Output speed sensor fixing: 1 ± 0,2
(5)
Oil overflow and drain fixing: 4 ± 0,2
(6)
Oil level plug:2,4 ±0,4
(7)
Oil pressure sensor fixing: 0,8 ± 0,1
Engines: KFV NFU RFN RHZ
C3 XSARA XSARA PICASSO
B2CP3EDDB2CP311D

Downloaded from www.Manualslib.com manuals search engine 352
CLUTCH
GEARBOX
TRANSMISSION
DRAINING / FILLING / TOPUP: AL4 GEARBOX
Checking the oil level.
Prior conditions:
Vehicle in horizontal position.
Check gearbox is not in backup mode.
Remove the oil filler cap
(2).
Add 0.5 litres extra oilinto the gearbox.
Foot on the brake, change through all the gears.
Selection lever in position
"P".
Engine running, at idle.
Oil temperature:
60°C (+8°C; 2°C).
Remove the oil level plug (3).
C3 TU3enginesDimension «X» = 81 mm
XSARA TU5
and EW10 enginesDimension «X» = 81 mm
XSARADW10
enginesDimension «X» = 77 mm
XSARA PICASSO EW10
enginesDimension «X» = 81 mm
Engines: KFV NFU RFN RHZ
C3 XSARA XSARA PICASSO
B2CP3AZD

Downloaded from www.Manualslib.com manuals search engine 353
CLUTCH
GEARBOX
TRANSMISSION
DRAINING / FILLING / TOPUP: AL4 GEARBOX
Thread of oil then "dripdrip".
Refit the plug (3), Tighten to 2,4± 0,2 m.daN.
"Dripdrip" or nothing.
Refit the oil level plug (3).
Stop the engine.Add
0.5 litresextra oil into the gearbox.
Repeat the oil level procedure.
NOTE:The level is correct at the moment the thread of oil becomes “dripdrip”.
Refit the oil level plug
(3)(equipped with a new seal), tighten to2,4±0,2 m.daN.
Checking the oil level (continued).
Refit the oil filler plug (3) (equipped with a new seal), tighten to 2,4± 0,2 m.daN.
An excessive level of oil can lead to the following consequences:
Oil heating up abnormally,
Oil leaks.
A level that is too low will result in the destruction of the gearbox.
Engines: KFV NFU RFN RHZ
C3 XSARA XSARA PICASSO
B2CP3AZD

Downloaded from www.Manualslib.com manuals search engine 416
BRAKES
BRAKE SPECIFICATIONS
Braking circuit with ABS REF
(a) Hydraulic circuit(b)Electrical circuit
(1)Master cylinder in tandem(2)Braking servo(3)Brake caliper (or drum at the rear)(4)Hub equipped with a bearing with an integral magnetic wheel(48 pairs of poles)(5)Wheel sensor(6)Brake fluid level sensor(7)Hydraulic block plus ECU(8)Stoplamp switch(9)Instrument panel(10)Diagnostic socket(11)Builtin systems interface (BSI)
B3GP02RP
C2

Downloaded from www.Manualslib.com manuals search engine 421
BRAKES
B3FP15XC
BLEEDING AND FILLING THE BRAKING SYSTEM
Tools.
[1]
Generic bleeding apparatus :«LURO»Bleeding, refilling.
Draining.
Drain the brake fluid reservoir (1)to the maximum(if necessary, use a clean syringe).
Disconnect the connector (4).
Uncouple the pipe (2).
Unscrew the shaft (3).
Remove the reservoir (1).
Empty the brake fluid reservoir (1).
Clean the brake fluid reservoir (1).
Refit:
The brake fluid reservoir
(1).
The shaft (3).
Couple the pipe (2).
Reconnect the connector (4).
Filling the braking system.WARNING:Use only those hydraulic fluids that are approved and recommended.
Fill the brake fluid reservoir (1).
Bleeding the braking system.WARNING:During the bleeding operation, take care to maintain the level of brake fluid in the reservoir
and to top it up, using only brake fluid that is clean and clear.
C2

Downloaded from www.Manualslib.com manuals search engine 423
BRAKES
B3FP160C
BLEEDING AND FILLING THE BRAKING SYSTEM (Continued)
With the bleeding apparatus.
Connect the bleeding apparatus [1]on the brake fluid reservoir (1).
Adjust the apparatus pressure to
2 Bars.
For each circuit:
Connect a transparent tube onto the bleed screw, submerge the other end of the tube in a clean container.
Open the bleed screw, wait until the fluid is flowing out without air bubbles. Close the bleed screw.
Remove the bleeding apparatus
[1].
Check the brake fluid level
(should be between «MINI»level and «MAXI»level).
Fill if necessary with the approved and recommended synthetic brake fluid.
Without the bleeding apparatus.
NOTE:Two operators are necessary.
For each circuit:
Apply the brake pedal to place the circuit under pressure.
Connect a transparent tube onto the bleed screw, submerge the other end of the tube in a clean container.
Open the bleed screw, wait until the fluid is flowing out without air bubbles.
Close the bleed screw. Remove the tool
[1].
NOTE:Recommence the process a second time if that is necessary.
Check the brake fluid level
(should be between «MINI»level and «MAXI»level).
Fill if necessary with the approved and recommended synthetic brake fluid.
C2