2004 Citroen C3 PLURIEL stop

Downloaded from www.Manualslib.com manuals search engine 372
AXLES
SUSPENSION
STEERING
REAR AXLE
Tightening torques (m.daN).
(1)
Rear axle fixing screw: 10 ± 1
(2)Antiroll bar:
(3)Rear axle crossmember:
(4)Rear suspension arm rubber mounting yoke:
(5)Rear suspension arm rubber mounting:
(6)Yoke / suspension arm fixing screw: 7,6 ± 0,5
(7)Rear suspension arm:
(8)Stub axle bearing nut: 20 ± 2 greased
(9) Damper:
(10)Damper upper fixing: 4,5 ± 0,4
(11)Damper lower fixing: 9,3 ± 1
(12)Suspension spring:
(13)Travel stop:
(14)Secondary brake cable guide and its support:
Antiroll bar
Diameter (mm)
HFX KFV
C3KFU NFU 8HX25,5
(tubular)
8HW 8HV 8HY
C3
PlurielKFV NFU 8HX26
(tubular)
B3CP0AFP
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 374
AXLES
SUSPENSION
STEERING
SUSPENSION
Front axle
(1) Nut fixing suspension leg on body: 6,5 ± 0,6
(2)
Damper
(16)Cup
(17)Damper nut.: 6,5 ± 0,6
(18)
Damper cup
(19)Ball bearing
(20)Spring thrust cup
(21)Travel stop cup
(22)Suspension spring
(23) Damper rod rpotector
(24)Travel stop
B3BP180D
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 375
AXLES
SUSPENSION
STEERING
SUSPENSION
Rear axle
(25)
Rear axle fixing screw: 10 ± 1
(26)
Antiroll bar:
(27)
Rear axle crossmember:
(28)
Rear suspension arm silentblock mounting yoke:
(29)
Rear suspension arm silentblock:
(30)
Suspension arm fixing screw on yoke:7,6 ± 0,5
(31)
Rear suspension arm:
(32)
Stub axle bearing nut : 20 ± 2 greased
(33)
Damper :
(34) Damper upper fixing screw: 4,5 ± 0,4
(35)
Damper lower fixing screw:9,3 ±0,9
(36)
Suspension spring:
(37)
Travel stop:
(38)
Secondary brake cable guide support:
Antiroll bar
EnginesDiameter (mm)
C3
AllTypes25,5
(tubular)
C3 Pluriel 26 (tubular)B3CP09UP
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 395
AXLES
SUSPENSION
STEERING
22/1 Steering ratio
MANUAL STEERING SPECIFICATIONSXSARA
Manual steering (continued)
Number of teeth
Pinion Steering rack
travel
(mm)
73,56 teeth
(RH helix)29(13)
Yellow thicknessmm4,3
Left hand driveSteering rackSteering stop
colour codeNumber
of steering
wheel turns
Length of the steering track rods (Preadjustment)= 371mm (Between balljoint centres)or391mm (Between the centre of the pivot balljoint and the contact face of the steering rack balljoint).

Downloaded from www.Manualslib.com manuals search engine 416
BRAKES
BRAKE SPECIFICATIONS
Braking circuit with ABS REF
(a) Hydraulic circuit(b)Electrical circuit
(1)Master cylinder in tandem(2)Braking servo(3)Brake caliper (or drum at the rear)(4)Hub equipped with a bearing with an integral magnetic wheel(48 pairs of poles)(5)Wheel sensor(6)Brake fluid level sensor(7)Hydraulic block plus ECU(8)Stoplamp switch(9)Instrument panel(10)Diagnostic socket(11)Builtin systems interface (BSI)
B3GP02RP
C2

Downloaded from www.Manualslib.com manuals search engine 420
BRAKES
B3FP16ED
HANDBRAKE (Adjustment)
Adjustment (continued).
A
: Drum brakes.B:Disc brakes.(10)Nut for adjusting cable tensions.
Remove:
The rear wheels.
The drums
(according to version).
Release the handbrake.Use a gauge set to measure at
«a»the travel of the lever
from its stop.
Adjust the nut
(10)to obtain a travel of less than or equal
to 1 mmat «a».
Refit the brake drums without tightening them (according
to version).
Action the handbrake lever 8 times with an effort of 40 m.daN.
With the handbrake released, check the travel of the
lever at
«a», using a gauge set.NOTE:The travel should be less than 1 mmand more
than 0,05 mm.
Refit:
The brake drums. The wheels.
The central console.
Check the operation of the handbrake.
C2

Downloaded from www.Manualslib.com manuals search engine 430
BRAKES
BRAKE SPECIFICATIONS
Braking circuit with ABS REF
(a) Hydraulic circuit
(b)Electrical circuit
(1)Master cylinder in tandem
(2) Braking servo
(3)Brake caliper (or drum at the rear)
(4) Hub equipped with a bearing with an integral magnetic wheel
(48 pairs of poles)
(5) Wheel sensor
(6) Brake fluid level sensor
(7) Hydraulic block plus ECU
(8)Stoplamp switch
(9)Instrument panel
(10)Diagnostic socket
(11)Builtin systems interface (BSI)
B3GP02RP
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 435
BRAKES
B3FP16ED
HANDBRAKE (Adjustment)
Adjustment (continued).
(10)
Nut for adjusting cable tensions
Remove:
The rear wheels.
The drums
(according to version).
Release the handbrake.Use a gauge set to measure at
«a»the travel of the lever
from its stop.
Adjust the nut
(10)to obtain a travel of less than or equal
to 1 mmat «a».
Refit the brake drums without tightening them (accor
ding to version).
Action the handbrake lever 8 times with an effort of
40 m.daN.
With the handbrake released, check the travel of the
lever at
«a», using a gauge set.NOTE:The travel should be less than 1 mm and more
than 0,05 mm.
Refit: The brake drums.
The wheels.
The central console.Check the operation of the handbrake.
C3 C3 PLURIEL