2004 CHRYSLER 300 M buttons

Canadian Programming/Gate Programming
Canadian frequency laws, and the technology of some
entry gates, require you to press and release the hand
held transmitter button every two seconds during pro-
gramming
Continue to press and hold the Universal Transceiver
button while you press and release the hand held trans-
mitter button until the frequency signal has been learned.
The Universal Transceiver light will flash slowly and
then rapidly when the programming is successful.
NOTE:When programming such a garage door opener
or gate, unplug the device to prevent possible damage to
the garage door or gate motor.
Operation
Press and hold the desired button on the Universal
Transceiver until the garage door or other device begins
to operate. The light in the display shows that the signal
is being transmitted. The hand held transmitter may also
be used at any time.
Reprogramming A Single Button
1. Press and hold the Universal Transceiver button to be
reprogrammed. Do not release until step 4 has been
completed.
2. When the indicator light begins to flash slowly (after
20 seconds) position the hand held transmitter 1 to 3
inches (3 to 8 cm) away from the button to be trained.
3. Press and hold the hand held transmitter button.
4. The Universal Transceiver indicator light will begin to
flash, first slowly, then rapidly. When the indicator lights
begin to flash rapidly, release both buttons.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79
3

Security
If you sell your vehicle, be sure to erase the frequencies.
To erase all of the previously trained frequencies, hold
down both outside buttons until the green light begins to
flash.
This device complies with part 15 of FCC rules and with
RS-210 of Industry Canada. Operation is subject to the
following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may be
received including interference that may cause undesired
operation.
NOTE:Changes or modifications not expressly ap-
proved by the party responsible for compliance could
void the user’s authority to operate the equipment.
HomeLinkis a trademark owned by Johnson Controls,
Inc.
GARAGE DOOR OPENER — IF EQUIPPED
Equipped in vehicles that have the optional Electronic
Vehicle Information Center (EVIC)
The HomeLinkUniversal Transceiver replaces up to
three remote controls (hand-held transmitters) that oper-
ate devices such as garage door openers, motorized
gates, or home lighting. It triggers these devices at the
push of a button, located on the overhead console. The
universal transceiver operates off your vehicle’s battery
and charging system; no batteries are needed.
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

2. Erase the factory test codes by pressing and holding
channels button one and three, of the universal trans-
ceiver, until CLEARED CHANNELS displays (about 20
seconds). Release the buttons.
3. Choose one of the three universal transceiver buttons
to program. Place the hand-held controller at the lower
left corner of the display and approximately 1 to 3 inches
away from the surface of the universal transceiver keep-
ing the display in view.4. Using both hands, simultaneously press and hold the
button on the hand-held transmitter and the button you
would like to program on the universal transceiver. The
display on the universal transmitter will show TRAIN-
ING. When the display indicates TRAINED, release both
buttons. Your universal transceiver is now programmed.
After a button has been trained, it will display TRANS-
MIT when pressed.
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

5. To program the other buttons, repeat steps 3 and 4. Be
sure to keep your hand-held transmitters in case you
need to reprogram the universal transceiver.
NOTE:If you do not successfully program the
HomeLinkUniversal Transceiver to learn the signal of
the hand-held transmitter, refer toProgramming Mul-
tiple Security Code Systems (Rolling Code)later in
this text or call toll-free for customer assistance at
1-800-355-3515 or on the internet at
www.homelink.com.
NOTE:In Canada, D.O.C. regulations require many
hand-held transmitters to stop transmitting after two
seconds. On these hand-held transmitters, transmission
will stop even though the light on the hand-held trans-
mitter stays lit.
If you have one of these hand-held transmitters, you
should press and release the hand-held transmitter
button every two seconds without releasing the uni-
versal transceiver button.
Release both buttons when the display indicates
TRAINED.
Reprogramming a Single Universal Transceiver
Button
1. Press and hold the desired universal transceiver but-
ton for about 20 seconds.
2. When the display indicates TRAINING, position the
hand-held transmitter one to three inches away from the
universal transceiver surface.
3. Press and hold the hand-held transmitter button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83
3

4. When the display indicates TRAINED, and the previ-
ous programming for the button has now been erased
and a new device has been programmed to the button.
This procedure will not affect any other programmed
buttons.
Operation
To operate, simply press the desired universal transceiver
button. The display shows that the appropriate channel
signal is being transmitted and the programmed device
should operate. For convenience, the hand-held transmit-
ter of the device may also be used at any time.
NOTE:If your hand-held transmitter appears to pro-
gram the universal transceiver, but your garage door
does not open, and your opener was manufactured after
1995, your garage door opener may have a multiple
security code system (rolling code system).
Multiple Security Code Systems (Rolling Code
System)
On garage door openers with a multiple code feature
(rolling code), the garage door opener transmitter code
changes after each use to prevent the copying of your
code.
Multiple security code (rolling code) garage door
openers and other devices which arecode protected
and manufactured after 1995, may be determined by
the following:
•
Reference the device’s owner’s manual for verification.
•The hand-held transmitter appears to program the
universal transceiver but does not activate the device.
To program a garage door opener with the multiple
security code (rolling code) feature, follow these
steps (The aid of a second person may make the
following programming procedures quicker):
1. Program your hand-held transmitter to the universal
transceiver by following the procedures previously de-
scribed in this section. (If you have already completed
this programming, proceed to the next step).
2. Locate the programming button on the garage door
opener motor head unit. The exact location and color of
the button may vary by garage door opener brand. If
there is difficulty locating the programming button,
reference the garage door opener owner’s manual or
contact HomeLinkat1-800-355-3515or on the internet
atwww.homelink.com.
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

3. Press the programming button on the garage door
opener motor head unit (which activates the program-
ming light).
4. Firmly press and release the programmed universal
transceiver button. Press and release the universal trans-
ceiver button a second time to complete the program-
ming process. (Some garage door openers may require
you to do this procedure a third time to complete the
programming.)
Your garage door opener should now recognize your
universal transceiver. You may use either your universal
transceiver or your original hand-held transmitter to
open your garage door.
For Your Security
If you sell your vehicle, be sure to erase the frequencies.
To erase all of the previously programmed frequencies,
hold down channel one and three buttons until
CLEARED CHANNELS is displayed.
NOTE:Individual channels can not be erased. You
must erase all three channels.
What May Cause The Universal Transceiver Not
To Work
•
The universal transceiver may not have been pro-
grammed correctly. Try reprogramming.
•The batteries in the hand-held transmitter may be
weak. New batteries may be required in your hand-
held transmitter.
•Place the hand-held transmitter at a different distance
from the universal transceiver (approximately 1 to 3
inches) (approximately 3 to 8 centimeters) and repro-
gram.
•The frequency of the programmed device’s hand-held
transmitter must be between 286MHz and 399MHz,
set by FCC part 15.205. (The back side of the hand-held
transmitter may indicate its frequency.)
•If you are unable to program the universal transceiver
after repeated attempts, you may contact HomeLink
at1–800–355–3515or on the internet at
www.homelink.com.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85
3

7. Repeat step 6 working clockwise around the vehicle
(Left Front, Right Front, Right Rear, Left Rear, Spare) until
all five TPM sensor positions are trained.
8. Return magnet to storage location.
If the display reads TRAINING COMPLETE, pressing
either the STEP, C/T, RESET, or MENU buttons will exit
the training mode.
If the display reads TRAINING ABORTED, move the
vehicle ahead at least 1 foot (30 cm) and complete steps
1–8 again.
For further assistance, questions, or comments about the
tire pressure monitor system, please call1–877–774–8473.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97
3

SETTING THE ANALOG CLOCK
To set the analog clock at the top center of the instrument
panel, press and hold the plus (+) or minus (-) buttons
until the setting is correct.
ELECTRONIC DIGITAL CLOCK
When the radio is on, pressing the TIME button will
allow you to select between displaying actual time con-
tinuously or information related to the mode which the
radio is in (i.e. in Radio mode, the radio frequency is
displayed.)
When the radio is off, time will not be displayed unless
the TIME button is pressed, and then the time will only
be displayed for 5 seconds. This function will operate
with the ignition switch in either the on or off positions.
You can ask your dealer to enable the digital clock to be
displayed continuously when the radio is off and the
ignition switch is on.
Clock Setting Procedure
1. Turn the ignition switch to the ON or ACC position.
Using the point of a ballpoint pen or similar object, press
either the hour (H) or minute (M) buttons on the radio.
The display will show TIME.
2. Press the H button to set hours or the M button to set
minutes. The time setting will increase each time you
press a button.
RADIO GENERAL INFORMATION
Radio Broadcast Signals
Your new radio will provide excellent reception under
most operating conditions. Like any system, however, car
radios have performance limitations, due to mobile op-
eration and natural phenomena, which might lead you to
believe your sound system is malfunctioning. To help
you understand and save you concern about these “ap-
parent” malfunctions, you must understand a point or
two about the transmission and reception of radio sig-
nals.
118 UNDERSTANDING YOUR INSTRUMENT PANEL