2004 Acura TL Owner's Manual

Doing any of the f ollowing af ter
pressing the MEMO button will
cancel the storing procedure.Not pressing a memory button
within 5 seconds.
Readjusting the seat position.
Readjusting the outside mirror
position.
Each memory button stores only one
driving position. Storing a new
position erases the previous setting
stored in that button’s memory. If
you want to add a new position while
retaining the current one, use the
other memory button. To select a memorized position, do
this:
Make sure the parking brake is set
(M/T) or the shif t lever is in Park
(A/T).
Press the desired memory button
(1 or 2) until you hear a beep, then
release the button. The system will move the seat and
outside mirrors to the memorized
positions. The indicator in the
selected memory button will f lash
during movement. When the
adjustments are complete, you will
hear two beeps, and the indicator will
remain on.
You cannot select a memorized
position if the transmission is in
Reverse. Shif t to another gear,
then select.
If the parking brake is not set, you
must press and hold the memory
button until the adjustment is
complete.
1.
2.
Notes f or vehicles with M/T
Driving Posit ion Memory Syst em
Inst rument s and Cont rols
Selecting a Memorized Position
94
MEMORY BUTTONS

To stop the system’s automatic
adjustment, do any of these actions:Press any button on the control
panel: MEMO, 1, or 2. If desired, you can use the
adjustment switches to change the
positions of the seat or outside
mirrors af ter they are in their
memorized position. If you change
the memorized position, the
indicator in the memory button will
go out. To keep this driving position
f or later use, you must store it in the
driving position memory.
Adjust the outside mirrors. Shif t out of Park. Push any of the adjustment
switches f or the seat.
Driving Posit ion Memory Syst em
Inst rument s and Cont rols95

Both f ront seats are equipped with
seat heaters. The ignition switch
must be in the ON (II) position to
usethem.PushtheHIsideof the
switch to rapidly heat up the seat.
After the seat reaches a comfortable
temperature, push the LO side of the
switch. This will keep the seat warm.The HI or LO indicator stays on until
youturnitoff bypushingthe
opposite side of the switch lightly.
In HI, the heater turns of f when the
seat gets warm, and turns back on
after the seat’s temperature drops. It
continues to cycle as long as you
leave it set on HI. The HI indicator
stays on as a reminder that you have
the heater on.
In LO, the heater runs continuously.
It does not cycle with temperature
changes.
Follow these precautions whenever
you use the seat heaters:
Use the HI setting only to heat the
seats quickly. Select the LO
setting when the seats f eel warm.
The HI setting draws large
amounts of current f rom the
battery.
Do not use the seat heaters, even
on the LO setting, if the engine is
lef t idling f or an extended period.
Thiscanweakenthebattery,
causing hard starting.
Because of the sensors f or the side
airbag system, there is no heater in
the passenger’s seat-back.
Seat Heaters
Inst rument s and Cont rols96
SEAT HEATERS

Your vehicle’s windows are electri-
cally-powered. Turn the ignition
switch to ON (II) to raise or lower
any window.
Each door has a switch that controls
its window. To open the window,
push the switch down and hold it.
Release the switch when you want
the window to stop. Close the
window by pulling back on the
switch and holding it.The driver’s door armrest has a
master power window control panel.
To open any window, push down on
the appropriate switch and hold it
until the window reaches the desired
position. To close the window, pull
back on the window switch. Release
the switch when the window gets to
the position you want.
Power Windows
Inst rument s and Cont rols97
DRIVER’S WINDOW
SWITCHMAIN
SWITCH
Closing a power window on
someone’s hands or fingers can
cause serious injury.
Make sure your passengers are
away from the windows before
closing them.

µ
The master control panel also has
these f eatures:
To open either f ront
window f ully, push the window
switch f irmly down to the second
detent, then release it. The window
automatically goes down all the way.
To stop the window f rom going all
the way down, pull back on the
window switch briefly.
To close either f ront window f ully,
pull back the window switch f irmly
to the second detent, then release it.
The window automatically goes all
the way up. To stop the window f rom
going all the way up, push down on
the window switch briefly. To open or close either f ront window
partially, push down or pull back on
the window switch lightly to the first
detent and hold it. The window will
stop when you release the switch.
The f ront passenger’s window switch
also has the AUTO f eature.
If either f ront window runs into any
obstacle while it is closing
automatically, it will reverse
direction, and then stop. To close the
window, remove the obstacle, then
use the window switch again.
Auto reverse stops sensing when the
window is almost closed. You should
always check that all passengers and
objects are away from the window
bef ore closing it.The MAIN switch controls power to
the passenger’s windows. With this
switch of f , the passenger’s windows
cannot be raised or lowered. The
MAIN switch does not af f ect the
driver’s window. To cancel this
feature, push on the switch again to
getittopopup.KeeptheMAIN
switch of f when you have children in
the vehicle so they do not injure
themselves by operating the
windows unintentionally.
The indicators inside the switches
come on when you turn the ignition
switch to ON (II).
Power Windows
Inst rument s and Cont rols
AUTO
Auto Reverse
98

If your vehicle’s battery is
disconnected or goes dead, or a f ront
window f use is removed, the AUTO
f unction could be disabled. If the
AUTO f unction is disabled, do the
f ollowing:The power window system has a key-
of f delay f unction. The windows will
stilloperateforupto10minutes
after you turn off the ignition.
Opening either f ront door cancels
the delay function. You must turn
the ignition switch to ON (II) again
bef ore you can operate the windows.
Start the engine. Push down on
the f ront window switch until the
window is f ully open.
Pull back on the f ront window
switch to close the window
completely, then hold the switch
f or a second or two more.
If the power windows do not operate
properly af ter resetting, have your
vehicle checked by an Acura dealer. 1.
2.
Power Windows
Inst rument s and Cont rols99

You can open all of the windows and
the moonroof f rom outside with the
remote transmitter.You can open and close the windows
and moonroof with the key in the
driver’s door lock. Turnthekeyclockwiseagain,and
hold it. All f our windows and
moonroof start to open. To stop
the windows and the moonroof ,
release the key.
Turn the key clockwise, then
release it. Insert the key in the driver’s door
lock.
To open: To open the windows and
moonroof f urther, turn and hold
the key again (within 15 seconds).
NOTE: If the windows and moonroof
stop bef ore the desired position,
repeat steps 2 and 3. To close the windows and
moonroof f urther, turn and hold
the key again (within 15 seconds). Turn the key counterclockwise
again, and hold it. All four
windows and moonroof start to
close. To stop the windows and
moonroof , release the key. Turn the key counterclockwise,
then release it. Insert the key in the driver’s door
lock.
To close:
Press the UNLOCK button once
to unlock the driver’s door.
Press the UNLOCK button a
second time, and hold it. The
passenger’s doors unlock, and all
f our windows and moonroof start
to open. To stop the windows and
moonroof , release the button.
To open the windows and
moonroof f urther, press the
button again and hold it. If the
windows and the moonroof stop
bef ore the desired position, repeat
steps 1 and 2.
You cannot close the windows or the
moonroof with the remote
transmitter. 1.
2.
3. 1.
2.
3.
4.
1.
2. 3.
4.
Power Windows, Moonroof
Inst rument s and Cont rols
Opening the Windows and
Moonroof with the Remote
Transmitter
Opening/Closing the Windows
and Moonroof with the K ey
100
UNLOCK BUTTON
Close Open

If the moonroof runs into any
obstacle while it is closing
automatically, it will reverse
direction, and then stop. To close the
moonroof , remove the obstacle, then
use the moonroof switch again.
Auto reverse stops sensing when the
moonroof is almost closed. You
should always check that all
passengers and objects are away
f rom the moonroof bef ore closing it.
To close the moonroof f ully, push
the switch firmly forward. The
moonroof automatically close all the
way. To stop the moonroof f rom
closing f ully, pull back the switch
brief ly.
Make sure everyone’s hands are
away f rom the moonroof bef ore
opening or closing it. To open or close the moonroof
partially, pull back or push f orward
the moonroof switch lightly and hold
it. The moonroof will stop when you
release the switch.
To tilt the moonroof , press straight
up on the center of the switch. To
stop the moonroof f rom tilting f ully
open, press the switch a second time. To slide the moonroof open, pull
back the moonroof switch f irmly.
The moonroof automatically opens
all the way. To stop the moonroof
f rom opening f ully, push the switch
f orward brief ly.
Moonroof
Inst rument s and Cont rols
Auto Reverse
101
MOONROOF SWITCH
Opening or closing the
moonroof on someone’s hands
or fingers can cause serious
injury.
Make sure all hands and fingers
are clear of the moonroof
before opening or closing it.