µµÎ
Î
Î
Î
T echnical Inf ormation
Specif ications
338
Dimensions
Weights
Air Conditioning Capacities
Excluding the oil remaining in the engine. Including the coolant in the reserve tank and that remaining in the
engine.
Reserve tank capacity: 4.5 US qt (4.3
)
196.7 in (4,995 mm)
71.7 in (1,820 mm)
54.5 in (1,385 mm)
114.6 in (2,910 mm)
61.0 in (1,550 mm)
60.6 in (1,540 mm)
HFC-134a (R-134a)
24.7 26.5 oz (700 750 g) ND-OIL8 18.0 US gal (68
)
1.61 US gal (6.1)
2.27 US gal (8.6)
4.9 US qt (4.6
)
5.6 US qt (5.3
)
3.2 US qt (3.0)
9.1 US qt (8.6)
1.11 US qt (1.05
)
1.16 US qt (1.10)
2.6 US qt (2.5)
6.9 US qt (6.5)
0.172 US gal (0.65
)
Length
Width
Height
Wheelbase
Track
Gross vehicle weight rating See the certification label attached
to the driver’s doorjamb.
Refrigerant type
Charge quantity
Lubricant type Fuel tank
Engine
coolant
Engine oil
Automatic
transmission
fluid
Differential
oil
Windshield
washer
reservoir
1:
2: Approx.
Front
Rear Change
Total
Change
Including filter
Without filter
Total
Change
Total
Change
Total
U.S. Cars
Canada Cars
1
2
µ
The treadwear grade is a compara-
tive rating based on the wear rate of
the tire when tested under controlled
conditions on a specif ied government
test course. For example, a tire
graded 150 would wear one and one-
half (1 1/2) times as well on the
government course as a tire graded
100. The relative perf ormance of
tires depends upon the actual condi-
tions of their use, however, and may
depart signif icantly f rom the norm
due to variations in driving habits,
service practices and dif f erences in
road characteristics and climate.
The tires on your car meet all U.S.
Federal Saf ety Requirements. All
tires are also graded for treadwear,
traction, and temperature perform-
ance according to Department of
Transportation (DOT) standards.
The f ollowing explains these
gradings.
Quality grades can be f ound where
applicable on the tire sidewall
between the tread shoulder and the
maximum section width. For
example:
The traction grades, f rom highest to
lowest, are AA, A, B, and C. Those
grades represent the tire’s ability to
stop on wet pavement as measured
under controlled conditions on
specif ied government test surf aces
of asphalt and concrete. A tire
marked C may have poor traction
perf ormance.
Warning: The traction grade
assignedtothistireisbasedon
straight-ahead braking traction tests,
and does not include acceleration,
cornering, hydroplaning, or peak
traction characteristics.
All passenger vehicle tires must
conf orm to Federal Saf ety
Requirements in addition to these
grades. T readwear
Unif orm T ire Quality Grading T readwear 200
Traction AA
Temperature A Traction AA, A, B, C
DOT T ire Quality Grading (U.S. Cars)
T echnical Inf ormation340
µ
µ
µ
µµ
µ
µ
µµ
µ µ
The tires that came on your car have
a number of markings. Those you
should be aware of are described
below.
Whenever tires are replaced, they
should be replaced with tires of the
same size. Following is an example
tire size with an explanation of what
each component means.
Vehicletype(Pindicates
passenger vehicle).
Tire width in millimeters.
Aspect ratio (the tire’s section
height as a percentage of its
width).
Tire construction code (R
indicates radial). Load index (a numerical code
associated with the maximum
load the tire can carry). Rim diameter in inches.
Speed symbol (an
alphabetical code indicating
the maximum speed rating).
Tire Identif ication Number (TIN) is
a group of numbers and letters that
look like the f ollowing example TIN.
This indicates that the tire
meets all requirements of
the U.S. Department of
Transportation.Manuf acturer’s
identification mark.
Tire type code. Date of manuf acture.
P
225
55
R 94
V 16
DOT
B97R
FW6X2202
T echnical Inf ormation
Tire Inf ormation
Tire Labeling
Tire Size
T ire Ident if icat ion Number
342
P225/55R16 94VDOT B97R FW6X 2202
