2003 YAMAHA YZF-R1 lock

PERIODIC MAINTENANCE AND MINOR REPAIR
6-30
6
NOTE:_ Using the alignment marks on each
side of the swingarm, make sure that
both chain pullers are in the same posi-
tion for proper wheel alignment. _
EC000096
CAUTION:_ Improper drive chain slack will over-
load the engine as well as other vital
parts of the motorcycle and can lead
to chain slippage or breakage. To
prevent this from occurring, keep
the drive chain slack within the
specified limits. _3. Tighten the locknuts, and then
tighten the axle nut to the specified
torque.
EAU03006
Lubricating the drive chain The drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly wear
out, especially when riding in dusty or
wet areas. Service the drive chain as
follows.
EC000097
CAUTION:_ The drive chain must be lubricated
after washing the motorcycle or
riding in the rain. _1. Clean the drive chain with kero-
sene and a small soft brush.
ECA00053
CAUTION:_ To prevent damaging the O-rings,
do not clean the drive chain with
steam cleaners, high-pressure
washers or inappropriate solvents. _
2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive
chain with a special O-ring chain
lubricant.
ECA00052
CAUTION:_ Do not use engine oil or any other
lubricants for the drive chain, as
they may contain substances that
could damage the O-rings. _
Tightening torque:
Axle nut:
150 Nm (15.0 m·kgf)
U5PWE1.book Page 30 Monday, July 8, 2002 10:28 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-36
6
EAU04876*
Replacing the fuses The main fuse and the electronic fuel
injection fuse are located under the rid-
er seat. (See page 3-17 for rider seat
removal and installation procedures.)
The fuse box, which contains the fuses
for the individual circuits, is located un-
der panel B. (See page 6-7 for panel
removal and installation procedures.)
If a fuse is blown, replace it as follows.
1. Turn the key to “OFF” and turn off
the electrical circuit in question.2. Remove the blown fuse, and then
install a new fuse of the specified
amperage.
EC000103
CAUTION:_ Do not use a fuse of a higher amper-
age rating than recommended to
avoid causing extensive damage to
the electrical system and possibly a
fire. _3. Turn the key to “ON” and turn on
the electrical circuit in question to
check if the device operates.
4. If the fuse immediately blows
again, have a Yamaha dealer
check the electrical system.
1. Headlight fuse
2. Signaling system fuse
3. Ignition fuse
4. Radiator fan fuse
5. Odometer and clock fuse (backup fuse)
6. Turn signal lights and hazard fuse
7. Spare fuse (× 3)
1. Main fuse
2. Electronic fuel injection fuse
3. Electronic fuel injection spare fuse
Specified fuses:
Main fuse: 50 A
Headlight fuse: 20 A
Signaling system fuse: 10 A
Radiator fan fuse: 15 A
Ignition fuse: 15 A
Electronic fuel injection
fuse: 15 A
Turn signal lights and
hazard fuse: 10 A
Odometer and clock fuse
(backup fuse): 10 A
U5PWE1.book Page 36 Monday, July 8, 2002 10:28 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-39
6
EAU03497
Replacing a turn signal light
bulb 1. Remove the turn signal light lens
by removing the screw.
2. Remove the defective bulb by
pushing it in and turning it counter-
clockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screw.
ECA00065
CAUTION:_ Do not overtighten the screw, other-
wise the lens may break. _
EAU04574
Replacing the license plate
light bulb 1. Remove the license plate light unit
by removing the screws.
1. Screw
1. Screw (× 2)
U5PWE1.book Page 39 Monday, July 8, 2002 10:28 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-43
6
EAU04915
Rear wheel To remove the rear wheel
EW000122
WARNING
_

It is advisable to have a Yamaha
dealer service the wheel.


Securely support the motor-
cycle so that there is no danger
of it falling over.
_1. Loosen the axle nut and the brake
caliper bolts.
2. Lift the rear wheel off the ground
according to the procedure on
page 6-40.3. Remove the axle nut, and then re-
move the brake caliper by remov-
ing the bolts.
ECA00146
CAUTION:_ Do not apply the brake after the
brake caliper has been removed,
otherwise the brake caliper pistons
will be forced out. _4. Loosen the locknut on each side of
the swingarm.
5. Turn the drive chain slack adjust-
ing bolts fully in direction
a.6. Push the wheel forward, and then
remove the drive chain from the
rear sprocket.
NOTE:_ The drive chain does not need to be
disassembled in order to remove and
install the rear wheel. _
1. Axle nut
2. Drive chain slack adjusting bolt
3. Locknut
1. Bolt (× 2)
2. Brake caliper
3. Brake caliper bracket
U5PWE1.book Page 43 Monday, July 8, 2002 10:28 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-47
6Engine overheating
EW000070
WARNING
_

Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.


After removing the radiator cap retaining bolt, place a thick rag, like a towel, over the radiator cap, and then
slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape. When the hiss-
ing sound has stopped, press down on the cap while turning it counterclockwise, and then remove the cap.
_CT-2AENOTE:_ If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolant
as soon as possible. _
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.Add coolant. (See NOTE.)
Start the engine. If the engine overheats again,
have a
Yamaha dealer check
and repair the cooling system.
There is
leakage.
There is
no leakage.
U5PWE1.book Page 47 Monday, July 8, 2002 10:28 AM

SPECIFICATIONS
8-4
8
Battery
Model GT12B-4
Voltage, capacity 12 V, 10 Ah
Headlight typeHalogen bulb
Bulb voltage, wattage × quantity
Headlight 12 V, 60/55 W × 2
Tail/brake light L.E.D.
Turn signal light 12 V, 10 W × 4
Auxiliary light 12 V, 5 W × 2
License plate light 12 V, 5 W × 1
Meter lighting L.E.D.
Neutral indicator light L.E.D.
High beam indicator light L.E.D.
Turn signal indicator light L.E.D.
Fuel level warning light L.E.D.
Oil level warning light L.E.D.
Engine trouble warning light L.E.D.
Engine speed indicator light L.E.D.
Fuses
Main fuse 50 A
Headlight fuse 20 A
Signaling system fuse 10 A
Radiator fan fuse 15 A
Ignition fuse 15 AOdometer and clock fuse
(backup fuse) 10 A
Electronic fuel injection fuse 15 A
Turn signal lights and
hazard fuse 10 A
U5PWE1.book Page 4 Monday, July 8, 2002 10:28 AM

INDEXAAir filter element, replacing ..................... 6-17
Anti-theft alarm ...................................... 3-11BBattery ................................................... 6-34
Brake and clutch levers, checking and
lubricating ............................................ 6-31
Brake fluid, changing ............................. 6-28
Brake fluid level, checking...................... 6-27
Brake lever............................................. 3-13
Brake light switch (rear), adjusting ......... 6-26
Brake pads, checking............................. 6-26
Brake pedal............................................ 3-14
Brake pedal, lubricating.......................... 6-32
Brake pedal position, adjusting .............. 6-25CCables, checking and lubricating............ 6-31
Care.........................................................7-1
Catalytic converter ................................. 3-16
Clutch lever ............................................ 3-13
Clutch lever free play, adjusting ............. 6-24
Conversion table ......................................8-5
Coolant .................................................. 6-13
Changing .......................................... 6-14
Checking .......................................... 6-13
Coolant temperature warning light............3-4
Cowlings and panels, removing and
installing ................................................6-5
DDimmer switch ....................................... 3-11
Drive chain, lubricating .......................... 6-30
Drive chain slack ................................... 6-29
Adjusting .......................................... 6-29
Checking .......................................... 6-29EEngine break-in ....................................... 5-3
Engine idling speed ............................... 6-19
Engine oil and oil filter cartridge ............... 6-9
Engine speed indicator light..................... 3-4
Engine stop switch................................. 3-12
Engine trouble warning light .................... 3-4
EXUP system ........................................ 3-24FFront fork, adjusting ............................... 3-19
Front fork, checking ............................... 6-33
Fuel ....................................................... 3-15
Fuel consumption, tips for reducing ......... 5-3
Fuel level warning light ............................ 3-3
Fuel tank breather hose ......................... 3-16
Fuel tank cap ......................................... 3-14
Fuses, replacing .................................... 6-36HHandlebar switches ............................... 3-11
Hazard switch ........................................ 3-12
Headlight bulb, replacing ....................... 6-37
Helmet holders ...................................... 3-18
High beam indicator light ......................... 3-4
Horn switch ........................................... 3-12
IIdentification numbers ..............................9-1
Ignition circuit cut-off system ..................3-25
Indicator and warning lights......................3-2KKey identification number .........................9-1LLicense plate light bulb, replacing...........6-39
Luggage strap holders ...........................3-23MMain switch/steering lock .........................3-1
Model label ..............................................9-2
Multi-function display................................3-6NNeutral indicator light ...............................3-4OOil level warning light ...............................3-3PParking.....................................................5-4
Part locations ...........................................2-1
Pass switch ............................................3-11
Periodic maintenance and
lubrication chart .....................................6-2
Pre-operation check list ............................4-1
U5PWE1.book Page 1 Monday, July 8, 2002 10:28 AM