2003 YAMAHA YZF-R1 lock

INSTRUMENT AND CONTROL FUNCTIONS
3-16
3
EAU04911
Fuel tank breather hose Before operating the motorcycle:

Check the fuel tank breather hose
connection.


Check the fuel tank breather hose
for cracks or damage, and replace
it if damaged.


Make sure that the end of the fuel
tank breather hose is not blocked,
and clean it if necessary.


Make sure that the end of the fuel
tank breather hose is positioned
outside of the cowling.
EAU01084
Catalytic converter This motorcycle is equipped with a cat-
alytic converter in the exhaust cham-
ber.
EW000128
WARNING
_ The exhaust system is hot after op-
eration. Make sure that the exhaust
system has cooled down before do-
ing any maintenance work. _
EC000114
CAUTION:_ The following precautions must be
observed to prevent a fire hazard or
other damages.

Use only unleaded gasoline.
The use of leaded gasoline will
cause unrepairable damage to
the catalytic converter.


Never park the motorcycle near
possible fire hazards such as
grass or other materials that
easily burn.


Do not allow the engine to idle
too long.
_
1. Fuel tank breather hose
1. Fuel tank breather hose
U5PWE1.book Page 16 Monday, July 8, 2002 10:28 AM

INSTRUMENT AND CONTROL FUNCTIONS
3-17
3
EAU04493
Seats Rider seat
To remove the rider seatPull up the rear corners of the rider seat
as shown, remove the bolts, and then
pull the seat off.To install the rider seat
Insert the projection on the front of the
rider seat into the seat holder as
shown, place the seat in the original
position, and then install the bolts.Passenger seat
To remove the passenger seat
1. Insert the key into the seat lock,
and then turn it counterclockwise.
2. While holding the key in that posi-
tion, lift the front of the passenger
seat and pull it forward.
1. Bolt (× 2)
1. Projection
2. Seat holder
1. Passenger seat lock
2. Unlock.
U5PWE1.book Page 17 Monday, July 8, 2002 10:28 AM

INSTRUMENT AND CONTROL FUNCTIONS
3-18
3
To install the passenger seat
1. Insert the projections on the rear
of the passenger seat into the seat
holder as shown, and then push
the front of the seat down to lock it
in place.
2. Remove the key.NOTE:_ Make sure that the seats are properly
secured before riding. _
EAU04489
Helmet holders The helmet holders are located on the
bottom of the passenger seat.
To secure a helmet to a helmet
holder
1. Remove the passenger seat. (See
page 3-17 for passenger seat re-
moval and installation proce-
dures.)
2. Attach the helmet to a helmet
holder, and then securely install
the passenger seat.
EWA00015
WARNING
_ Never ride with a helmet attached to
a helmet holder, since the helmet
may hit objects, causing loss of
control and possibly an accident. _
ECA00128
CAUTION:_ Some helmets may contact the muf-
fler when secured to the right side
helmet holder because of their size
or shape. Be sure that your helmet
does not contact the muffler when it
is secured to the helmet holder. _To release a helmet from a helmet
holder
Remove the passenger seat, remove
the helmet from the helmet holder, and
then install the seat.
1. Projection (× 2)
2. Seat holder
1. Helmet holder (× 2)
U5PWE1.book Page 18 Monday, July 8, 2002 10:28 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-6
6 2. Remove the bolts and screw, and
then loosen the quick fastener
screws 1/4 turn counterclockwise.
3. Slide the cowling backward at the
area shown.4. Disconnect the turn signal light
lead coupler.
5. Remove the screws, and then take
the cowling off.
To install the cowling
1. Install the screws.
2. Connect the turn signal light lead
coupler.
3. Place the cowling in the original
position.
4. Install the screw and the bolts,
tighten the quick fastener screws,
and then install the quick fasteners.
NOTE:_ To install the quick fastener, push the
center pin out so that it will protrude
from the fastener head, insert the fas-
tener into the cowling, and then push
the protruding pin in until it is flush with
the fastener head. _
1. Quick fastener screw (× 6)
2. Screw
3. Bolt (× 2)
1. Turn signal light lead coupler
2. Screw (× 2)
1. Quick fastenerAfter removal
Before installation
U5PWE1.book Page 6 Monday, July 8, 2002 10:28 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-7
6
EAU04555
Cowling B
To remove the cowlingRemove the bolts, loosen the quick fas-
tener screws 1/4 turn counterclock-
wise, and then take the cowling off.To install the cowling
Place the cowling in the original posi-
tion, and then tighten the quick fastener
screws and install the bolts.
EAU04531
Panels A and B
To remove one of the panelsLoosen the quick fastener screws 1/4
turn counterclockwise, remove the
screw, and then take the panel off.
To install the panelPlace the panel in the original position,
tighten the quick fastener screws, and
then install the screw.
1. Quick fastener screw (× 4)
2. Cowling B
3. Bolt Right side
1. Bolt
2. Quick fastener screw (× 3)
3. Cowling BLeft side
1. Quick fastener screw (× 2)
2. Screw
E_5pw_Periodic.fm Page 7 Monday, July 8, 2002 10:58 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-25
62. Remove cowling B. (See page 6-7
for cowling removal and installa-
tion procedures.)
3. Loosen the locknut at the crank-
case.
4. To increase the clutch lever free
play, turn the adjusting nut in di-
rection
a. To decrease the clutch
lever free play, turn the adjusting
nut in direction
b.
5. Tighten the locknut.
6. Install the cowling.
EAU01357
Adjusting the brake pedal
position The top of the brake pedal should be
positioned approximately 38–42 mm
below the bottom of the footrest brack-
et as shown. Periodically check the
brake pedal position and, if necessary,
have a Yamaha dealer adjust it.
EW000109
WARNING
_ A soft or spongy feeling in the brake
pedal can indicate the presence of
air in the hydraulic system. If there
is air in the hydraulic system, have a
Yamaha dealer bleed the system be-
fore operating the motorcycle. Air in
the hydraulic system will diminish
the braking performance, which
may result in loss of control and an
accident. _
1. Locknut
2. Clutch lever free play adjusting nut
(crankcase)
a. Distance between brake pedal and footrest
bracket
U5PWE1.book Page 25 Monday, July 8, 2002 10:28 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-28
6 Observe these precautions:


When checking the fluid level,
make sure that the top of the brake
fluid reservoir is level.


Use only the recommended quali-
ty brake fluid, otherwise the rubber
seals may deteriorate, causing
leakage and poor braking perfor-
mance.


Refill with the same type of brake
fluid. Mixing fluids may result in a
harmful chemical reaction and
lead to poor braking performance.


Be careful that water does not en-
ter the brake fluid reservoir when
refilling. Water will significantly
lower the boiling point of the fluid
and may result in vapor lock.


Brake fluid may deteriorate paint-
ed surfaces or plastic parts. Al-
ways clean up spilled fluid
immediately.


As the brake pads wear, it is nor-
mal for the brake fluid level to
gradually go down. However, if the
brake fluid level goes down sud-
denly, have a Yamaha dealer
check the cause.
EAU03976
Changing the brake fluid Have a Yamaha dealer change the
brake fluid at the intervals specified in
the NOTE after the periodic mainte-
nance and lubrication chart. In addition,
have the oil seals of the master cylin-
ders and calipers as well as the brake
hoses replaced at the intervals listed
below or whenever they are damaged
or leaking.

Oil seals: Replace every two
years.


Brake hoses: Replace every four
years.
1. Minimum level mark
Recommended brake fluid: DOT 4RearRear
U5PWE1.book Page 28 Monday, July 8, 2002 10:28 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-29
6
EAU00744
Drive chain slack The drive chain slack should be
checked before each ride and adjusted
if necessary.
To check the drive chain slack
1. Place the motorcycle on a level
surface and hold it in an upright
position.NOTE:_ When checking and adjusting the drive
chain slack, the motorcycle should be
positioned straight up and there should
be no weight on it. _
2. Shift the transmission into the neu-
tral position.
3. Move the rear wheel by pushing
the motorcycle to locate the tight-
est portion of the drive chain, and
then measure the drive chain
slack as shown.
4. If the drive chain slack is incorrect,
adjust it as follows.
EAU03608
To adjust the drive chain slack
1. Loosen the axle nut and the lock-
nut on each side of the swingarm.
2. To tighten the drive chain, turn the
adjusting bolt on each side of the
swingarm in direction
a. To loos-
en the drive chain, turn the adjust-
ing bolt on each side of the
swingarm in direction
b, and then
push the rear wheel forward.
a. Drive chain slack
Drive chain slack:
40–50 mm
1. Axle nut
2. Drive chain slack adjusting bolt
3. Locknut
4. Alignment marks
U5PWE1.book Page 29 Monday, July 8, 2002 10:28 AM