2003 YAMAHA GRIZZLY 660 light

4-17 1. Lights switch
2. Engine stop switch
3. Start switch “”
4. Horn switch “”
1. Contacteur d’éclairage
2. Coupe-circuit du moteur
3. Contacteur du démarreur “”
4. Contacteur de l’avertisseur “”
1. Interruptor de luces
2. Interruptor de paro del motor
3. Interruptor de arranque “”
4. Interruptor de la bocina “”
EBU00053
Handlebar switches
EBU00735
Light switch
Turn the switch to the “” position to switch on
the low beam and the taillight.
Turn the switch to the “” position to switch on
the high beam and the taillight.
Turn the switch to the “OFF” position to switch off
the headlight and the taillight.CAUTION:
Do not use the headlight with the engine
turned off for more than thirty minutes. The
battery may discharge to the point that the
starter motor will not operate properly. If this
should happen, remove the battery and re-
charge it.
EBU00606
Engine stop switch
Make sure that the engine stop switch is in the
“” position. The engine stop switch controls ig-
nition and can be used at all times to stop the en-
gine, especially in an emergency. The engine will
not start or run when the engine stop switch is
turned to “”.
U5KM60.book Page 17 Thursday, June 21, 2001 2:40 PM

4-19 1. Lights switch
2. Engine stop switch
3. Start switch “”
4. Horn switch “”
1. Contacteur d’éclairage
2. Coupe-circuit du moteur
3. Contacteur du démarreur “”
4. Contacteur de l’avertisseur “”
1. Interruptor de luces
2. Interruptor de paro del motor
3. Interruptor de arranque “”
4. Interruptor de la bocina “”
EBU00607
Start switch “”
The starter motor cranks the engine when this
switch is pushed.CAUTION:
See starting instructions prior to starting the
engine. (See page 6-3 for details.)
EBU00059
Horn switch “”
Press the switch to sound the horn.
U5KM60.book Page 19 Thursday, June 21, 2001 2:40 PM

4-25 1. Differential gear lock switch “4WD”/“LOCK”
2. Lever
1. Contacteur de blocage du différentiel “4WD”/“LOCK”
2. Levier
1. Selector de bloqueo del diferencial “4WD”/“LOCK”
2. Palanca
Differential gear lock switch “4WD”/“LOCK”
To lock the differential gear in 4WD, make sure the
on-command four-wheel-drive switch is set to
“4WD”, stop the ATV, move the lever to
position
b, and then set the switch to “LOCK”.
When the differential gear is locked, the differential
gear lock indicator light (“DIFF.LOCK”) will come
on along with the indicator “” in the speedometer
unit display. To release the differential gear lock,
stop the ATV and set the switch to “4WD”.
DIFF.
LOCK
U5KM60.book Page 25 Thursday, June 21, 2001 2:40 PM

4-27
WARNING
_ Always ride at a slow speed when the ATV is in
4WD-LOCK, and allow extra time and distance
for maneuvers.
All wheels turn at the same speed when the dif-
ferential is locked, so it takes more effort to
turn the ATV. The amount of effort is more the
faster you go. You may lose control and have
an accident if you cannot make a sharp
enough turn for the speed you are traveling. _ NOTE:_

When the switch is set to “LOCK”, the differ-
ential gear lock indicator light will flash until
the differential gear is locked.


When the indicator light is flashing, turning
the handlebar back and forth will help the dif-
ferential gear lock to engage.


Riding before the differential gear lock is
properly engaged (e.g., when the indicator
light is flashing) will cause the engine speed
to be limited until engagement is complete.


When the ATV is in 4WD-LOCK, the maxi-
mum traveling speed is limited to 35 km/h.
_
U5KM60.book Page 27 Thursday, June 21, 2001 2:40 PM

4-37 1. Drive select lever
1. Levier de présélection
1. Palanca de selección de marcha
1. Recoil starter
1. Lanceur à réenroulement
1. Arranque por tracción de cable
EBU00608
Drive select lever
The drive select lever is used to shift your machine
into the low, high, neutral, reverse and park posi-
tions. (Refer to pages 6-11 ~ 6-15 for the drive se-
lect lever operation.)
EBU00975
Recoil starter
Firmly grasp the handle and pull slightly until en-
gagement can be felt. Then pull forcefully, being
careful not to pull the rope all the way out.
WARNING
_ Always shift the drive select lever to “P” park
position before starting the engine, otherwise
the ATV could start to move unexpectedly,
which could cause an accident. _
U5KM60.book Page 37 Thursday, June 21, 2001 2:40 PM

4-53
EBU00748
Auxiliary DC jack
The auxiliary DC jack is located at the front right
side of the ATV. The auxiliary DC jack can be used
for suitable work lights, radios, etc. The auxiliary
DC jack can only be used when the main switch is
in the “ON” position.
1. Turn the headlight switch to the “OFF” posi-
tion.
2. Start the engine. (See pages 6-3 ~ 6-9.)
3. Open the auxiliary DC jack cap and insert the
accessory power plug into the jack.
4. When the auxiliary DC jack is not being used,
cover it with the cap. Maximum rated capacity for the auxiliary DC
jack:
DC 12 V, 120 W (10 A)
1. Auxiliary DC jack cap
1. Capuchon de la prise pour accessoires
1. Tapa de la toma de CC auxiliar1. Auxiliary DC jack
1. Prise pour accessoires
1. Toma de CC auxiliarU5KM60.book Page 53 Thursday, June 21, 2001 2:40 PM

4-55
CAUTION:

Do not use accessories requiring more
than the above maximum capacity. This
may overload the circuit and cause the
fuse to blow.


If accessories are used without the engine
running or with the headlight turned on,
the battery will lose its charge and engine
starting may become difficult.


Do not use an automotive cigarette lighter
or other accessories with a plug that gets
hot because the jack can be damaged.
U5KM60.book Page 55 Thursday, June 21, 2001 2:40 PM

5-1
EBU00113
PRE-OPERATION CHECKS
Before using this machine, check the following points:
ITEM ROUTINE PAGE
BrakesCheck operation, free play, fluid level and fluid leakage.
Fill with DOT 4 brake fluid if necessary.5-7 ~ 5-9,
8-91 ~ 8-105
FuelCheck fuel level.
Fill with fuel if necessary.5-11 ~ 5-13
Engine oilCheck oil level.
Fill with oil if necessary.5-15 ~ 5-17,
8-33 ~ 8-43
Coolant reservoirCheck coolant level.
Fill with coolant if necessary.8-55 ~ 8-65
Final gear oil/
Differential gear oilCheck for leakage.5-19 ~ 5-21,
8-43 ~ 8-53
ThrottleCheck for proper throttle cable operation. 5-23, 8-89
Wheels and tiresCheck tire pressure, wear and damage.5-27 ~ 5-33,
8-113 ~ 8-115
Fittings and FastenersCheck all fittings and fasteners. 5-23
LightsCheck for proper operation. 5-25, 8-127 ~ 133
Axle bootsCheck for damage. 8-67
U5KM60.book Page 1 Thursday, June 21, 2001 2:40 PM