D01556
WRONG
D01563
01±16
±
INTRODUCTION REPAIR INSTRUCTION
AVENSIS REPAIR MANUAL (RM1018E)
(±) terminal cable is disconnected. If necessary, be
sure to initialize the system.
(b) HANDLING OF ELECTRONIC PARTS (1) Do not open the cover or case of the ECU unlessabsolutely necessary (If the IC terminals are
touched, the IC may be rendered inoperative by
static electricity).
(2) To disconnect electronic connectors, pull the con- nector itself, not the wires.
(3) Be careful not to drop electronic components, such as sensors or relays. If they are dropped on a hard
floor, they should be replaced and not be reused.
(4) When cleaning the engine with steam, protect the electronic components, air filter and emission±re-
lated components from water.
(5) Never use an impact wrench to remove or install temperature switches or temperature sensors.
(6) When checking the continuity at the wire connector, insert the tester probe carefully to prevent terminals
from bending.
4. REMOVAL AND INSTALLATION OF FUEL CONTROL PARTS
(a) PLACE FOR REMOVING AND INSTALLING OF FUEL SYSTEM PARTS (1) Work in a place with good air ventilation and without anything that could ca\
use combustionaround you such as a welder, grinder, drill, electric motor or stove.
(2) Never work in a place such as a pit or nearby a pit, as there is a possi\
bility that vaporized fuel will collect in those places.
(b) REMOVING AND INSTALLING OF FUEL SYSTEM PARTS (1) Prepare a fire extinguisher before starting operations.
(2) To prevent static electricity, install a ground on the fuel changer, vehicle and fuel tank, and donot spray much water so as to prevent slipping.
(3) Never use any electric equipment like an electric motor or a working lig\
ht, as they may create
sparks or a high temperature.
(4) Never use an iron hammer, as it may create sparks.
(5) Dispose of shop rags containing fuel deposits separately.
5. REMOVAL AND INSTALLATION OF ENGINE INTAKEPARTS
(a) If any metal tip is mixed in the inlet pass, this may give a bad effect to the engine and turbocharger.
(b) When removing and installing the inlet system parts,
close the opening of the removed inlet system parts and
the engine with a clean waste cloth or gum tape.
(c) When installing the inlet system parts, check that there is no mixing of a metal tip.
http://vnx.su
L1L2
D02612
L2
L1
D01201
L2
L1
D01202
±
INTRODUCTION REPAIR INSTRUCTION (1NZ±FE/2NZ±FE)
01±5
1ZZ±FE,3ZZ±FE ENGINE REPAIR MANUAL
(RM923E)
NOTICE:
Do the torque checking with the lower limit value of the torque toleranc\
e.
(4) Depending on the seal lock agent to apply, there may be a case where it is necessary to leave
it for a specified time until it hardens.
(b) Gaskets: When necessary, use a sealer on gaskets to prevent leaks.
(c) Bolts, Nuts and Screws:
Carefully observe all specifications for bolt tightening torques. Always\
use a torque wrench.
(d) Torque When Using Extension Tool with Torque Wrench:(1) In case of tightening by extending the entire lengthof the torque wrench combined with SST or tool, if
you tighten until the reading of the torque wrench
reached the specified torque value, the actual
torque becomes excessive.
(2) In this text, only the specified torque is described.
In case of using SST or extension tool, find the read-
ing of the torque wrench by the formula.
(3) Formula T'=T x L2/(L1 + L2)
T'Reading of torque wrench Nm kgf cm ft lbf
TTorque Nm kgf cm ft lbf
L1Length of SST or tool (cm)
L2Length of torque wrench (cm)
10. REMOVAL AND INSTALLATION OF FUEL CONTROL PARTS
(a) Place for Removing and Installing Fuel System Parts:
(1) Place with good air ventilation and without anything flammable such as welder, grinder, drill, elec-
tric motor or stove in the surroundings.
(2) Never work in a place like a pit or nearby pit as there is a possibility that\
vaporized fuel fills those places.
(b) Removing and Installing of Fuel System Parts:
(1) Prepare a fire extinguisher before starting the operation.
(2) For prevention of the static electricity, install a ground on the fuel changer, vehicle and fuel tank,and do not spray much water so as to prevent slipping.
http://vnx.su
